Search Documents

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

By J E. Everett, M L. James

When iron ore is crushed and split into lump and fines components, there are systematic differences between the lump and fines grades. Generally the lump product is richer in iron and lower in the other minerals, compared to the fines product. The grade differences between lump and fines, together with the lump percentage, are referred to as the ælump algorithmÆ. Mine estimates of grade, based on exploration or blasthole drilling, relate to head grade. The ælump algorithmÆ predicts lump and fines product grades from the head grade. This knowledge is important when developing mine plans. Different ore types can be expected to have systematically different lump algorithms. Previously, lump algorithms for specific ore types have been estimated by running the crusher with a single ore type over a sample period. This method is costly, interferes with production, and yields results of limited statistical power. It has been found that weighted-least-squares (WLS) multiple regression can be used to ascribe lump algorithms to different ore types, provided sample periods have sufficiently varied ore type mixes. This study discusses the method and its application to the analysis of Mining Area C crusher production records to estimate the separate lump algorithms, which could be applied to the different ore types. The analysis has enabled the set up of lump algorithms in the production system, to improve the grade control of lump and fines product. Some other relevant applications of the WLS multiple regression approach are also considered.

Jan 1, 2005

Mineral policy is now generally regarded as a function reserved to government. Government is reponsible for the economic health and progress of nations, and must therefore interest itself in minerals as a basic national resource. Government should therefore identify objectives which it sees as suitable and necessary for the mineral industry so that the industry can play its part in achieving national goals. It should provide the legislative framework and policy guidelines to enable these objectives to be achieved. The essential objective of a national mineral policy should be rational development of the nation's minerals resources. To achieve this, it need not be too formal; broad guidelines are enough. But it must be dynamic, to keep pace with the changing circumstances of the mineral industry in the world scene and the changing requirements of government. It should be flexible, recognising that there is no such thing as a "typical" mineral deposit; above all it should represent the outcome of a continuing dialogue between government and industry. Both government policy and corporate planning need to be formulated on the practical understanding of the potential economic value of the mineral sector and what it can contribute to the nation's prosperity. There needs to be a common understanding of the wide range of the costs of risks that may arise through the exploration and development stages and of the uncertainties affecting ventures at the production stage. There needs to be a common understanding that the size and importance of the mineral sector is determined in the long run by the level of investment in exploration. The development of a continuing understanding between government and industry should lead to the formulation of ground rules which ensure the continuance of a strong industry able to adapt to the changing world scene and make its contribution to national growth and wellbeing.

Jan 1, 1986

Following plant trials in 1972 Mount Lyell installed an AMDEL On Stream Analysis system for measuring copper and density on the flot- ation feed and final plant tailing streams, in August 1973. As a result of poor performance of the final tailing system these probes were changed over to the rougher tailing stream, back to the final tailing stream and finally to the final copper concentrate stream where the system is currently performing satisfact- orily. The history of the development of the system to its current operational status is Described.

Jan 1, 1978

By M Thomas, M Caccetta, C Laukamp, A Hacket, M Jones, A Rodger, M Verrall, R Hewson

A mineral systems approach was used to interpret precompetitive airborne mineral mapping geoscience data for iron oxide copper gold (IOCG) exploration in the Starra area, Eastern Succession, Mount Isa Inlier. Selected minerals were chosen to map possible source rocks/fluids as well as intersecting structural/fluid pathways that could have transported mineralising fluids into domains of contrasting rocks/fluids where there was potential for physicochemical gradients to precipitate metals. Ferric and ferrous iron contents and white mica abundance were useful mineral criteria to identify theMount Dore Granite of theWilliams-Naraku Batholith as a potential source of æoxidisedÆ fluids rich in Fe, K and potentially Cu-Au. The Mount Dore Shear Zone (MDSZ) intersects the western margin of this granite with the highest contents and changes in composition of the white mica are peripheral to this contact within the granite. This together, with the fact that the entire N-S length of the MDSZ in the study area (~16 km) is abundant in white mica are evidence of K-rich fluids had preferentially moved along this pathway. To the south, the MDSZ intersects a domain comprising massive ironstone bodies as well as numerous graphitic horizons. This interpreted æreducedÆ domain is well mapped using the æopaqueÆ mineral products, as well as by white mica, which is pervasively developed and extends 2 km either side of the MDSZ fault into the meta-sedimentary sequences. The chemistry of this white mica also changes progressively away from the MDSZ, becoming more Si-rich (longer wavelength) towards the contact with massive ironstone bodies in the west and the graphitic units in the east, both of which represent sites of known Cu-Au mineralisation. Beyond these contact zones of interpreted æoxidised fluidsÆ with reduced rocks/fluids, there is either a rapid change to Si-poor white mica and/or no white mica developed, ie major æchemicalÆ gradient change. These mineral mapping results provide evidence for a direct link between possible source rocks and sites of IOCG metal deposition as well as extending the associated alteration zonation which had previously been mapped/published at the metre-scale to the kilometre-scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By G D. Price

The Golden Blocks Goldfield is located in the Slaty Creek area,North West Nelson, about 20 km west of Collingwood. Alluvial gold was discovered in Slaty Creek in 1861. Gold was mined from quartz veins up to 1.5 m thick at nine mines from the 1890s until the closure of the Aorangi Mine in 1911. Total production from the Golden Blocks Goldfield is estimated at 46 000 ounces of gold. The Aorangi Mine was the largest mine, with a recorded production of 27 978 ounces of gold at an average grade of 36 g/t. Quartz veins containing gold and sparse sulphide mineralisation occur in a slightly metamorphosed, complexly deformed over-turned sequence of Lower Ordovician sandstones and shales. Primary gold mineralisation is associated with intensely deformed zones that occur near or at carbonaceous shale and sandstone contacts. Some eighty-five percent of all gold production (39 000 ounces) came from four mines confined to the stratigraphically lowest, most widespread shale unit. The quartz veins exhibit textures consistent with a hydraulic fracturing mode of vein formation with fissure infill vein types predominating over replacement textures. Stylolites of carbonaceous material and recrystallization features within the veins suggest multiple phases of deformation. The lack of wall rock alteration, and low primary fluid inclusion temperatures of 200¦ - 265¦ indicate that the ore fluids were associated with a low temperature epithermal system. A model consistent with similar mineralisation styles observed in Ordovician sediments from Pacific Rim occurrences is presented. The high grades (up to 100 g/t) mined from the upper levels of several mines suggests supergene enrichment processes associated with the Upper Cretaceous weathering surface. The Golden Blocks Goldfield has had no modern exploration. The most recent exploration was undertaken in the early 1980s. There are known acid intrusives in the area, with potential for the application of new models of intrusive-related gold mineralisation.

Jan 1, 2004

The efficiency with which it is expected that a particular coal may be burnt in a power station boiler significantly affects the value of the coal. Consequently many laboratory tests have been developed to provide data on the combustibility of coal. Computer modelling of coal combustion has also provided insight into limits on coal burn- out. Such modelling suggests that burnout of bituminous coal in a power station boiler will be strongly influenced by physical limits on the diffusion of oxygen to the individual coal particles. Coal chemical reactivity appears to be relatively less important. As a consequence of the diffusional limits, significant improvement in burnout is achieved either by producing less large p.f. particles or by providing sufficient furnace residence time to burn the large particles. Field data from a variety of power stations supports these cn.clusions. Burnout was also found to correlate well with volatile content for a number of coals from widely different sources. This is expected as the high vola- tile coals produce less residual char to be burned by the relatively slow heterogeneous Combustion.

Jan 1, 1987

The word "mine" means different things to different people. To a professional in the mining industry, it may mean trucks and shovels, overburden dumps, headframes, mill buildings, and the other conventional nuts and bolts that constitute an operating mine. To an environmental- ist it may mean bulldozed trees and tailings dams. To a mining engineer who has spent a significant proportion of his career in mine and prospect evaluation, it can mean a hole in the ground with a liar at the top. The liar in this case is frequently not so through design but through ignorance. The purpose of this paper is to contribute in a small way to en- lightening that ignorance. In doing so, it will foster more effective deployment of the pool of risk capital available to the industry.

Jan 1, 1982

By K Kellett, A V. Metzner

From its discovery in 1845 ion exchange has continually improved technically to an extent where it is now in wide use commercially in many industries including mining and environmental. Purity Systems Inc. (PSI) has made advances in the development of metals capture materials such that metals recovery using the PSI patented technology is now a viable economic process for many previously rejected applications. PSI, in conjunction with Ammtec Limited, have developed cost effective advanced processes and systems.The presentation will introduce the chemistry behind the materials and its relevance to the chelation and ion exchange methods. The applicability of the PSI resin technology to copper, cobalt and nickel recovery and the engineered systems options available will be discussed as well as piloting at Titan Resources NL Radio Hill mine at Karratha in Western Australia.

Jan 1, 2002

By J Canterford

There is an apparent push to develop and commercialise "new and innovative" process flow sheets. A not-too-difficult reality check clearly demonstrates that the success rate of this push is not particularly significant and in fact could be regarded as a waste or misappropriation of R&D funding and the associated brain power. As Julian Sumner Miller would comment "why is this so?" To put it bluntly, many of the so-called innovative developments are equivalent to gold plating the dunny door - visually interesting but of very limited practical value. This presentation encapsulates some personal lessons learnt over the past 45 years.CITATION:Canterford, J, 2013. Developing a ænew and innovativeÆ process flow sheet - Traps for all players of all ages, in Proceedings MetPlant 2013 , pp 1-5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

There are serious problems in forecast- ing accurately and achieving this goal depends on good quality information, correct assumpt- ions and sound analysis. planner. The forecaster must focus attention on a number of key areas of interest. These areas include major economic trends and changing GNP structure, consumption time series, end-use consumption patterns and substitution potential, accurately updating data bases (up to 5 years ahead), random factor estimation and examination of both long term and secondary mine potential. While metal price forecasting has suffered due to recent uncertainties, with increased importance on planning tools and cost analyses, it is still a necessary function. Forecasting is subject to the real world and the metal industry is made up of imperfect markets in a dynamic state. The real world provides the challenge to improve the accuracy of forecasting.

Jan 1, 1983

This paper describes the characteristics of blasting which set it apart from other methods of breaking rock. The mechanism of rock breakage and the influence of rock proper- ties are then discussed. The strain and fragmentation produced by a cylindrical charge does not change once the charge is longer than 16 blasthole diameters. The influence of bench geometry, charge length and drill diameter are then examined. It is shown that spherical charges have advantages over long slender cylindrical charges. By selection of the appropriate drill diameter, explosive and charge configuration the optimum blasting practice for a given rock to give suitable fragmentation and muckpile profile for sub- sequent handling can be found. The fragmentat- ion depends not only on rock and explosive properties but also on the pattern which dictates how effectively the cracking is utilised. The size distribution of the fragments is given by the Rosin - Rammler equation. Undesirable cracking of the rock in the final wall can be controlled by the careful design of blasts as they approach the final wall. Finally, it is concluded that because of the distance to which blasting can fracture and then displace rock it is suited for the breakage of large volumes of rock.

Jan 1, 1978

By A G. Greenwood

Research into cemented rock fill at Mount Isa Mines Limited since 1992 is described. The key mechanisms controlling segregation during stope filling with cemented rock fill are described and include the gravity flow mechanism which is described in detail. Examples are provided to demonstrate these mechanisms. Comparisons are made between Mount Isa MinesÆ cemented rock fill and slurry-based cemented rock fills. Recent backfill stability modelling using a three-dimensional finite element program is described.

Jan 1, 1998

By C Ferron, R Massimi

There is approximately 240 000 tonnes of arsenic trioxide dust stored in underground chambers at the Giant Mine in Yellowknife, Northwest Territories, Canada. To minimise the amount of arsenic released to the environment, a number of closure alternatives are being considered. One alternative is to mine the dust, encapsulate it and dispose the mixture into a secured landfill. The potential leaching behaviour of the encapsulated dust was examined in a laboratory programme. Cylinders of arsenic trioxide dust mixed with cement/aggregate and bitumen were prepared. The dust content varied between zero per cent and 60 per cent of dry weight charge. The cement cylinders were tested for strength, leaching and freeze/thaw durability. The bitumen cylinders were tested for leaching only. The results show that increasing dust content in the cement cylinders negatively impacts the strength and the freeze/thaw durability of the samples. A contributing factor is likely the high water to cement ratio in the samples. Leaching tests show that arsenic release from cement cylinders increase with increasing dust content. Arsenic concentrations in leachates do reach a plateau at a certain point in time. Arsenic release from bitumen cylinders was significantly lower compared to cement cylinders. Arsenic concentrations eventually were less than 0.05 mg/L in samples containing up to 25 per cent arsenic trioxide dust. Arsenic leaching rates were found to decrease by an order of magnitude over the course of three months.

Jan 1, 2003

By Boyd G

Deep mining in the Collie Basin has suffered with high levels of water flow and sediment in-rushes throughout its 90 year history. Current day experience in working conventional bord and pillar by mainly mechanised means is that advance to the dip is impeded at about the 150m depth of cover by excessive water flow and pressure bursts. Extensive analysis of exploration borehole data and reconstruction of depositional environments helped define important hydrogeological characteristics of roof and floor aquifers, aquitards and aquicludes. Hydraulic parameters were estimated with some accuracy using indirect methods, and later confirmed by pump testing. Groundwater flow modelling showed that mine scheduling would have to be a balance between down dip and lateral development if aquifer pressure heads were to be decreased to suitable levels. Since pressure reduction in aquifers immediately above and below the mine opening was. identified as the key aim in groundwater control, a series of trial in-pit dewatering holes were installed, and demonstrated pressure heads could be reduced at rates compatible with a mine extraction sequence which, in turn, controlled the rate of down dip mine advance. A case history of the successful application of in-pit dewatering systems within difficult hydrological conditions for mining is described, with emphasis on the close collaboration required between hydrologists, mine planners and operations personnel.

Jan 1, 1988

The application of new and currently practised mining techniques in new areas and at greater depths necessitates considerable and immediate research effort. This effort is aimed at identifying the factors which make a particular method suitable and economically viable in a given geological, structural and operational environment. These factors, together with greatly enhanced knowledge of a deposit at the exploration and planning stage, allow selection of the most appropriate and efficient mining method in a new area such that coal resource recovery is maximised in a cost effective manner. Current research and future requirements for research into mining methods and associated equipment and mine services are reviewed.

Jan 1, 1981

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971