Search Documents

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

By Agrawal R. D, Kapoor M. L

Activity of FeO in the ternary system MgO-FeO-CaO in contact with metallic iron has been measured at 1000 K employing the cell.PtIFe, (Mg, Fe, Ca)OIZr02 - CaOIFe, FeOlPt. Measured data are used to study the phase stability relations in the system MgO-FeO-CaO and an isothermal section at 1000 K through this system is drawn.

Jan 1, 1987

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

By E M. Rykaart

The design of soil covers as part of the remediation initiatives for mine waste facilities is common practice and more and more engineers are faced with designing these facilities. The design issues associated with these soil covers are complex and requires a good understanding of unsaturated flow. More engineers are making use of numerical models to predict how cover designs would perform, and this has been necessitated by the high non-linearity associated with solving unsaturated flow problems. There are numerous numerical models available to the prospective users and they are all simplifications of reality using different assumptions. The users of these models often do not understand the limitations of the models but rather select a model based on ease of use, and that lends to increasingly erroneous designs being proposed for construction. This paper describes a comparative evaluation of a cover design using four different codes available today; SoilCover, SWIM, HYDRUS-2D and HELP. The paper does not propose to measure these codes up against each other and make statements about which is better than the other but rather illustrates how the assumptions in each code affect the outcome. The data set used for the comparative study is a well calibrated data set that that has been collected over a long period in time and that has been collected according to strict controls. The authors present the pitfalls of numerical modelling of the surface flux boundary conditions, as well as present guidelines towards appropriate use of these modelling tools.

Jan 1, 2003

By A B. Richards

Effective control of blast vibration and flyrock requires that significant factors be identified and quantified, that the blast be designed to ensure both blasting efficiency and compliance with applicable limits, and that the blast design be effectively implemented by field personnel. Significant factors contributing to ground vibration and airblast are: charge mass; distance and direction relative to the blast; drilling design: burden, spacing; stemming height and material type; hole diameter and depth; and initiation sequence and direction.In addition, airblast may be strongly influenced by shielding and meteorological conditions. Ground vibration is also influenced by the transmission characteristics of the ground and soil. Flyrock throw is determined by charge mass, burden, stemming height, blasthole diameter and depth. The contribution of each of the factors has been quantified and models developed to enable the environmental outcomes of blast design to be predicted. Environmental blast design is necessary to ensure compliance with regulatory limits and the implementation of æsafeÆ exclusion zones for flyrock clearance. This paper discusses the models used for environmental blast design and demonstrates the often significant effects that lapse during implementation of the design can have on predicted outcomes. In practice, drillers and shotfirers are sometimes confronted with situations that require modifications to the blast design to cope with the real site situation. Methods are presented that may be used by drillers and shotfirers to evaluate the effect of these modifications, the tolerances that must be reached during their work practice and checking procedures, and the consequences of their actions.

Jan 1, 2004

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

This paper is a tribute to the late Dr Donald Martin Hausen as a father of applied mineralogy. His dedication to promoting the field through technical societies and through his professional work was outstanding, and his activities as a humanitarian are noteworthy. Dr HausenÆs involvement in technical societies included organising and conducting the only ICAM congress that was held in the USA, co-founding and nurturing the Process Mineralogy Committee within the American Institute of Mining, Metallurgy and Petroleum Engineers, and participating in CAM, the International Mineral Processing Congress, as well as other technical societies. The Process Mineralogy Committee that he co-founded has continuously organised annual meetings in the USA by conducting a series of sessions, and 17 books on the proceedings from those sessions have been published. As an applied mineralogist Dr Hausen solved many problems in exploitation and processing of minerals, metals and materials, especially gold. He helped to find many Carlin-type gold orebodies by outlining targets using alteration halos as determined by X-ray diffractometry, and he defined mineral characteristics that affected gold metallurgy and cyanidation. It is also noteworthy that Dr Hausen and his wife, Mary, opened their arms and home to many foster children and were instrumental in their placement in many homes. They also sponsored refugees from south-east Asia, taught them English, housed them, and provided constant support until the refugees became responsible and independent US citizens.

Jan 1, 2008

By G Smart, D Ward, J Grace

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. It is an underground sublevel cave (SLC) operation mining approximately 5 Mt per annum. Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. These data form the basis for forecasting and on-going systems analysis which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions, visual grade estimates and draw point sampling are routinely recorded. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Draw point recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Statistical variance controls are also employed to analyse mine and plant performance and guide actions.

Jan 1, 2003

By Hu Y, Li D, Qu G

In this paper the structural mechanism of the gold - lixiviant complex is investigated. The results show that there are two common characteristics in the outer orbitals for all the gold lixiviants: a) a (Y -type of HOEO to form the L-*Au co-ordination bond, and b) a it type f LUEOs, with symmetry the same as that of 5d orbitals of Au, to form L

Jan 1, 1993

There is a difference in design aspects between steel linings and rubber linings for grinding mills. The basic design rules for rub- ber are described as well as the liner designs for different applications.

Jan 1, 1978

The restructuring of the minerals industry has created new challenges for the design and delivery of professional development, and difficult decisions for potential participants. New technologies offer some new methods of delivery, but fall short in providing all of the benefits of face-to-face participation. This paper is intended to be a catalyst for discussion of the issues involved in delivery and participation in cost-effective, relevant and timely professional development.

Jan 1, 2000

By North R. A

The Queensland Mining Act 1968-1972 has now been in force for almost two years. The Act was completely re-written and has made for easier working, e.g., there is no distinction now between Gold Mining Leases and other Mining Leases. For the first time in the history of Queensland, provision has been made for caveats, so that options etc. can be protected. The chief problem which has arisen so far has been the question of the Government issuing mining leases to the holder of an Authority to Prospect over areas which are included iri its Authority. Litigation has taken place and an Appeal, it is understood, will shortly be heard by the Privy Council. The provisions dealing with labour conditions have been brought up-to-date and generally speaking, they are quite clear as to the responsibility of the Lessee. The Mining on Private Land Act has been repealed and the provisions relating to mining on private land are now a part of the Mining Act itself. Previously, the holder of a- mining freehold did not have to pay royalty on

Jan 1, 1974

By Komosa T, Muir D. M

Mixtures of ammonia and cyanide at low concentrations leach gold selectively from copper-gold ores. The effects of various reagent compositions on three different ore types containing between 0.3 - 1.5 per cent Cu are reported. It is shown that the results and optimum compositions vary according to the ore, which is attributed in part to the mineralogy and adsorption of solution species on the mineral surfaces. The solution chemistry of the Cu-NH3-CN system indicates that Cu(CN)a - and Cu(CN)3 species are involved in the leaching mechanism. Rotating disc studies on pure gold and copper are reported which show that the Cu(CN)32- species leach gold at about half the rate of CN but leach copper at the same rate. The presence of ammonia retards the leaching rate further. Mixtures of Cu(CN)a3- and NH3 effectively leach gold from Telfer tailing without leaching copper. The role of ammonia appears to be to control the precipitation of copper rather than the kinetics of leaching.

Jan 1, 1991

An Innovative Process for Comprehensive Utilisation of Clay-Vanadium Ores By adopting conventional processing technologies such as flotation, gravity concentration, and magnetic separation, it is difficult to enrich vanadium mineral effectively. At present, vanadium extraction process usually has not the mineral processing enrichment procedure, but rather uses direct hydrometallurgical process: roasting - leaching - precipitating vanadium for obtaining high quality V2O5 product. But it results in problems, for instance, high consume of auxiliary materials like acid and alkali, serious pollution and high cost of vanadium extraction. In the project study on the ore of a certain clay vanadium mineral, by adopting the test process: scrubbing raw ore with reagents added in - dispersing and segregating with reagents - grading enrichment, vanadium concentrate product with higher grade was made by virtue of reagent's selective inhibiting, and the purpose of upgrading the raw material used for vanadium extraction with hydrometallurgical process is achieved. The process technology obtained from project study features simple process structure, low equipment investment, low cost of mineral processing and pollution-free to environment. It provides high efficient and practical technology for the comprehensive utilisation of clay vanadium mineral, and has a prominent prospect for its popularisation and application.

Sep 13, 2010

By M Revell

The paste fill system at BHP CanningtonÆs underground silver-lead-zinc mine is described. The first of its type in Australia, the paste fill system has been operational since December 1997. Key technical and operational learnings since the first underground stope was filled are presented. Issues addressed include plant performance, pipe wear and failure, automatic control, rheology and in situ performance.

Jan 1, 2000

Spatial data processing using geographic information systems produces qualitative results which are superior to those from other existing software tools. However, the answers to various quantitative questions in mining operations is often limited by the capacity of the GIS to process appropriate spatial data. The efficient operation of a large underground mine demands that an adequate GIS be put in place.

Jan 1, 1995

By Houghton BF

Ruapehu is an extremely active andesitic composite volcano, built in at least four cone- building episodes over the last 250 ka. The volcano was constructed by a variety of extrusive and subplinian, strombolian, phreatomagmatic and dome-related explosive eruptions from summit, flank, and satellite vents. The volcano may be subdivided into the cone itself, of volume 110 km3, and a surround- ing epiclastic ring plain of similar size. Four facies associations can be recognised at Ruapehu,-two each on the cone and on the ring plain. Neither cone nor ring plain provides a complete record of the history of the volcano. The cone is dominated by the products of extrusive eruption, as primary pyroclastic deposits are seldom preserved, being rapidly removed by erosion from the steep water- saturated and/or snow-covered flanks of the cone. The ring plain consists of the products of mostly explosive activity forming an alter- nation of primary pyroclastic fall deposits and material transported from the cone by lahars, floods and debris avalanches and then rapidly reworked in sediment-choked hyperconcentrated Streams.

Jan 1, 1987

Probably no other country or coutinent has so many rich deposits of various different minerals as Australia. Long ago in the days of my boyhood in the old land the marvellous discoveries of high percentage copper at Burra Burra, Peak Downs, Yudanamutana, and other mines, was one of the principal themes of conversation in mining circles whilst the specimens of malachite, azurite, etc, brought home by returning miners were the admiration of my boyish eyes.Later on the WalIaroo and Moonta mines still further helped to heighten the reputation of Australia as a copper-producing country. During the 21 years that the writer has been resident in the Australian colonies, other mineral deposits have sprung into prominence, and with a Mount Bischoff for tin, a Broken Hill for silver and lead, and a Mount Morgan for gold, Australia can now boast that it has had within its borders the leading mines of the world, in four different minerals, and still at least maintains that pre-eminence in gold, silver and tin. To the miner from the old land, Australian mining is at first a revelation and a wonder. In very many instances he looks in vain for the regular strike and dip of the veins he has been accustomed to'Smooth hanging and foot alls are often wanting. 'Huge irregular deposits, like those mentioned above, viz., Burra Burra, Mount Bischoff, Broken Hill, and Mount Morgan, are mysteries that will take time to fathom-if, indeed, they are ever thoroughly understood and in many a smaller deposit there is much to interest alike the professor in the college and the miner in the mine.

By A Crawford, P Manton

Telfer is a gold/copper operation, currently operating one open pit mine and one underground mine. The ore processing plant consists of two parallel trains involving semi-autogenous mill, ball mill and crusher (SABC) grinding, flotation and leaching. Due to receiving relatively high grade underground ore for over half of its total feed, Train 1 frequently experienced cleaning circuit overloading during high production periods. This resulted in losses in recovery and ineffective concentrate upgrade. As a quick and simple solution, the Train 1 copper flotation circuit was reconfigured to send concentrate from the first two rougher cells directly to the final concentrate and return the cleaner scavenger tailings to the third rougher cell. These modifications have resulted in a 1.4 per cent increase in plant copper recovery with no change in final concentrate grade. Preliminary results also indicate gold recovery has increased by more than 1 per cent since the circuit reconfiguration. Other benefits include less spillage, more friendly circuit to operate and a more consistent metallurgical performance. Focus for the next phase of optimisation is on concentrate upgrade. A number of opportunities have been identified and are currently being investigated, including staged reagent addition, single stage cleaning of the first two copper rougher concentrates, regrinding of the remaining copper rougher concentrate prior to cleaning and process control based on a machine vision system.

Jan 1, 2009

The seminar had its origins in an Inquiry into the Box Flat Disaster and one of the conclusions from this Inquiry was that there should be a better dissemination of technical knowledge and the results of research work. As a result of this Mr. W. Roach, Chief Inspector of Coal Mines in Queensland and Mr. R. Menzies, Chief Inspector of Coal Mines in N.S.W. had a meeting to see how this could be done. They concluded that it would be difficult to have the sort of regular meetings that would be possible where distance was not significant, but a seminar would be a major step toward satisfying this particular conclusion of this Inquiry. As a consequence, Mr. Roach, who is on the Committee of the Southern Queensland Branch of the Institute, suggested when the Branch programme was being planned this year that a meeting of this type should be held, and the Mine Fires Seminar which was held today is the result. We have received a great deal of support in arranging the Seminar. First and foremost I wish to acknowledge support from the National Coal Board in United Kingdom. Not only have they released Dr. Willett for a period of six to seven weeks to visit Australia, conduct the Seminar and give a series of lectures in various areas through the country, they have also borne the brunt of the financial support that has been necessary to make this possible. In addition we have received considerable support from many organisations in Australia. I 'mentioned this

Jan 1, 1973