Search Documents

By Lu T. K

A new type of rockbolting system, the self drilling rockbolt, has been studied to develop a 'single pass' bolt for use in rockbolt installation in underground engineering. This single pass bolt forms the basis of a Rapid Face Bolting system which will reduce the amount of time spent in securing a roof during the operation of a continuous miner in the development of a panel.The installation efficiency and anchorage tests were performed in the laboratory on the self drilling bolt and the traditional resin anchorage. bolt. The results of both bolts are cmmnared.

Jan 1, 1993

An account of milling "methods and costs at Mount Isa Mines Limited up to the year 1938 has been published. The present paper outlines the methods since adopted in the milling of lead-zinc ores and presents a description of the equipment now being provided for the milling of copper ore.The programme approved for the mining, milling and smelting of both lead-zinc and copper ores involves the milling 9f 50,000 tons of lead-:-zinc ore and 35,000 tons of copper ore per month.The crushed ores will be delivered to the surface from alternate levels through No. 2 Ore shaft and conveyed to their respective crude ore bins at the crushing plant. The ores will be crushed and milled in separate circuits in common buildings and the tailings will be stored on a common tailings dump. The water services to the two circuits will be separate.LEAD ZINC PLANTCrushing PlantThe crushing plant described in the previous paper was located adjacent to the Urquhart shaft. The crushing plant had grown considerably over the years by the addition of a 4ft. BY-mons shorthead crusher and a set of Traylor 72 in. x 20 in. crushing rolls and, whilst operating satisfactorily, was difficult to maintain and cramped in many places. As a satisfactory layout for the new copper crushing plant could not be made in the vicinity of the, existing plant, it was decided to construct a new plant on the western side of theconcentrator building and provide identical equipment in...

Jan 1, 1953

The increasing introduction of high capacity mechanical equipment into the coal mines of New South Wales following. tforld War II brought with it problems of roof support. Rapidly advancing headings in difficult country could not be supported with heavy, close,timbering due to the time involved in installation and the reduction of available' space for the movement of machines. _ The installation of low cost, space saving, rapidly installed roof supports became a necessity if the new mechanical equipment wa-s to be allowed to operate at maximum efficiency. As, a result of experience in the United States of America, the system of roof support using steel reinforcing bolts began to find increasing, popularity in the mechanised mines in this State. From the somewhat'crude methods of in- stallation adopted in some of the, early trials, the practice of roof bolting has advanced into a-highly technical operation, requiring care and skill to ensure optimum results.

Jan 1, 1971

This paper discusses the use of tapered roller bearings in conveyor idlers. It shows that in medium and high capacity systems, tapered roller bearings can offer significant cost and performance advantages. In the next ten years, conventional conveyors will face increased competition from unconventional belt conveyors, pneumatic systems, pipeline "slurry" systems, unit trains and so on. The conveyor industry must meet these challenges by innova- tive use of technology. Conventional belt conveyors must continue to show the lowest cost per tonne-km or lose their position in the market. Tapered roller bearings can contribute to the achievement of this goal. The concurrent resources boom and liquid fuel crises may well see a decline in the use of heavy trucks for bulk material handling over moderate distances 10 to 50 km. There appears to be a trend in the conveyor industry to go to higher speeds with improved belting in conven- tional widths. The transmission of more material over a given period of time will place more demands on conveyor idler bearings. Australia has in general followed the European practice of using deep groove ball bearings in conveyor idlers.

Jan 1, 1978

The first mining in Western Australia probably commenced some 40 000 years ago when Aborigines arrived and began quarrying stone for tools and weapons, and ochre for decoration. The earliest documented mining by European settlers took place in 1850 on a small lead vein in the bed of the Murchison River, reported by the explorer A C Gregory. However, it was the discovery of gold in the Kimberley region in 1885 that first drew wider attention to the State's mineral potential.

Jan 1, 1992

The reasons for selecting two stage pebble milling in preference to conventional methods of grinding are discussed. Commissioning of the first section was completed in October, 1969. Improvements in both the operating and engineering aspects were then incorporated in the section commiss ioned in March, 1971.

Jan 1, 1975

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

I began my interest in sample preparation when I joined the Institute of Nuclear Sciences in 1962. I worked in the fields of rock dating and stable isotope geochemistry. Preparing a sample could take several days and the analysis took another day or more, so great care was taken with each sample. In 1968 I changed to mineral exploration analysis and was surprised to find that there was much less care in how a sample was taken and prepared. Virtually every sample was processed in the same way. In the use of ring and puck mills, Australia and New Zealand were among the world leaders. It took another ten years before labs in North America changed over from disc mills. In 1975, my partner and I divided our business into two parts. He took the laboratory into his consulting laboratory business and I took the small business that we had started, making ring and puck mills. For the next six years I was RocklabsÆs only employee. In the 1980s and 1990s, sampling specialists like Francis Pitard and Dominique Francois-Bongarcon began to make a difference in the understanding of what constitutes good sampling and preparation practice. They and others took courses on the new concepts of Sampling Theory, as developed by Pierre Gy. The desire for better procedures lead to the development of new machines, including the big bowl pulverisers from Australia, jaw crushers that could crush finely like our Boyd Crusher, rotating dividers of new designs and flow-through ring and puck mills. Other machines did not fare so well, including rolls crushers, cone crushers and hammer mills.

Jan 1, 2008

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By Hare G

The emphasis in Australia, until recently, has been on large scale mining methods with drive sizes in excess of 4.5 metres square and the acceptance of high dilution ratios, even when working in relatively narrow orebodies. The rising cost of extracting and treating the recovered ore and the lower prices available in the world markets has seen a growing trend to narrow mining methods.Traditionally narrow orebody mining has been carried out using hand held drilling methods and rail mounted boggers. Recent advances in mobile equipment now offers the operator of narrow method mines the opportunity to completely mechanise the mine from the drilling, through bogging to haulage, while maintaining minimal dilution in drive sizes to two metres wide or less.

Jan 1, 1993

By A L. Hemphill

Conventional models, based on pulp kinetics, were regressed directly to steady-state data from a nine-stage platinum flotation plant, to provide a basis for optimisation studies. æFroth factorsÆ were used to characterise the froth in each stage and a ædepressant factorÆ was used for gangue minerals, to account for addition of depressant to the cleaners. These factors improved the fit, but differences between plant and model of up to 50 per cent were still present in a number of streams in the cleaning circuit. A new model was developed, which incorporated two rate constants for the recycle of particles from the froth. These parameters provided a workable approximation of the distribution of probabilities of particles being recycled in plant cells, depending upon where particles appeared at the surface. The feed streams were characterised by two pulp kinetic parameters and the above recycle parameters, for all minerals and all stages. The fit to the data was improved very significantly, when compared to the use of conventional pulp-based models with several pulp rate parameters. This relatively simple model did not require additional data from batch tests and it was suitable for plant simulations.Simulations of various strategies for plant operation were tested, allowing the simulator to vary the concentrate flows from all or some of the stages, in order to maximise platinum recovery. The simulator was imbedded in an automatic optimiser and constraints on chrome content or mass flow of final concentrate were used. The simulations of the existing circuits demonstrated that an improvement in recovery, (for a constant concentrate mass) of about 0.5 per cent was possible, by optimising all concentrate flows. A significant reduction in the flow of scavenger concentrate and an increase in the recycle flows in the cleaners were noted. The results of simulations of various changes to the circuit configuration are also discussed. An increase in recovery of 1.4 per cent (for constant concentrate mass) has been achieved in recent simulations, through circuit changes. However, it was necessary to keep the mass pull of concentrate, per unit area, within typical limits.

Jan 1, 2005

By Fourney W. L, Weaver T. A

A large number of single borehole crater-forming shots were analyzed in terms of correlating the crater parameters with explosive weight. The objective was to determine a scaling rule for which the explosive weights varies over many orders of magnitude and covers many different geologic materials. Included in the data base are type and weight of the explosive, geologic medium and degree of saturation, charge depth-of-burial, crater dimensions, and crater rim (lip) measurements. An alternative scheme to the usual plot of scaled depth-of-burial versus scaled volume removed was desired. The proposed technique uses a plot of the logarithm of the explosive weight, Y, versus the logarithm of the slant length, R', calculated from the known depth-of-burial of the explosive and the measured crater radius. A plot of Log Y in kilotons versus Log R' in meters from all the crater tests in this data base resulted in a straight line with a of slope 0.31 and showed good correlation between the variables Log Y and Log R'. Since the crater data includes many geologic materials, different explosives (including nuclear tests), and large differences in charge weight, the straight line fit suggests that the type and strength of the geologic materials play a subordinate role to explosive energy in crater formation.\

Jan 1, 1990

By Delahey G, Dunne R

At New Celebration Gold Mine the advent of treating primary sulphide ores resulted in decreased gold recoveries of four to ten per cent. The grind coarsened due to an increase in ore hardness and gold in the residue was found to be associated with pyrite. Finer grinding improved recoveries but was impractical as production rates would have decreased to unacceptable levels. An alternative approach that has proved to be viable combines both gravity separation, to recover the coarse gold bearing sulphides, and then regrinding the concentrate in a tower mill prior to releaching in the cyanide leach circuit. The tailings treatment plant was commissioned in December 1990 and details of the first 18 months' operations are Provided.

Jan 1, 1993

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

Author Biography William Poole was born in Sydney, NSW in August 1868. He was educated at Sydney Grammar School. William spent two and a half years as a cadet in the Railway Construction Branch of the NSW Department of Public Works doing office and field work. He then undertook a civil engineering course at Sydney University. Following this he was employed for six years as assistant and resident engineer at the Water Conservation Branch, NSW and was in responsible charge of various field operations, surveys, river gaugings and works of constructions including a large timber weir and also a concrete weir on the Macquarie River, NSW. He then undertook a mining and metallurgical course at Sydney University and became a graduate (BE) with honours in civil engineering, mining engineering and metallurgy. He then spent four and a half years with BHP Co, one and a half years at Broken Hill in the mining and concentration works and three years at the smelting works in Port Pirie, SA, in the latter case he was metallurgist and night superintendent and during that time had responsibility and control at night of the blast furnaces and, during the last 15 months, of the whole of these large works. The author left the Port Pirie, SA works to assume the position of Director of the State School of Mines at Charters Towers and had responsible control of the establishment and also lectured in mining, surveying and structure. William Poole was honoured to hold membership in the following organisations: Assoc M Inst C E, L S of NSW, M Aus Inst M M, Assoc Inst M & M (London).

Jan 1, 2006

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008

By Azizan A

The paper presents the results of chlorination of beneficiated rutile and struverite (a tantalum-niobium bearing, rutile type mineral in alluvial tin deposits) by carbon tetrachloride in the range 623¦K to 773¦K. The chlorination of rutile could reach near completion at 773¦K in about an hour. The process was found to follow a modified pore-blocking law, with the basic reaction constant K varying inversely with the particle size, so that the basic process may be a reaction under interface control (chemical control) as modified by the pore blocking effect. The pore blocking factors for the various experimental conditions were evaluated and the predicted curves showed good agreement with the experimental data. In the case of Struverite, a similar kinetic behaviour was observed but the chlorination process was relatively slower than that in rutile. It was also observed that in struverite, niobium got chlorinated faster, followed by tantalum and titanium, indicating a good possibility of separation by chlorination using carbon tetrachloride.

Jan 1, 1996

In the 100 years since the formation of The Australasian Institute of Mining and Metallurgy there have been significant changes in all aspects of the mining industry.A number of the changes have been driven by technical evolution or necessity, others have been driven by developments in the application of the products produced from the mining of minerals. Other changes have been driven by shifts in community values.

Jan 1, 1993

By Lo YC, Pate WT

In recent years there has been a great deal of interest in ways to optimise the performance of mineral processing plants. This paper describes a methodology developed for optimisation of autogenous and semiautogenous mills. The methodology involves plant sampling, batch testing, modelling, computer simulation, control strategy evaluation and implementation. The models have been tested in plant operations to verify the research findings and predictions. Two example applications of this approach to plant optimisation are presented. Benefits reported in these two examples are in the range of four - eight per cent increase in size reduction efficiency.

Jan 1, 1993