Search Documents

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A B. Bayooke, A C. Robertson

In terms of underground tunnelling in metres advance per capita, Australasia compares well with the best world performers. This is because of the large number of metalliferous mines, coalmines and civil tunnelling projects, with the Australian tunnel advance for civil and mining projects exceeding 625?km/a. In terms of hard rock quarry extraction, Australia produces approximately 200?Mt/a of aggregates, roadbase, fill material and specialist rock products from its quarries, which equates to approximately 8?t/capita. Australian mining and tunnelling contractors are also of world standard and are used to excavating in a variable range of ground conditions in a competitive environment. One author has been involved in tunnel and underground space planning and quarrying in Australia for the past 25 years and predicts that, over the next 20 years, there will be a major swing towards underground space for commercial uses. This paper identifies the potential uses of underground commercial excavation and the planning and geotechnical challenges for the future. Underground quarrying creates new opportunities to extend existing quarries within their urban footprint with minimum impact on the surrounding community. Investigations by the authors reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. However, cities such as Helsinki have been planned in detail to utilise the rock resources beneath them. Brisbane is used as a case study for a practical application of commercial underground space and underground quarrying in Australia.CITATION:Bayooke, A B and Robertson, A C, 2014. Geotechnical challenges for underground commercial space and quarrying in Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 µm. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 µm. The circuit product P80 ranged between 42–55 µm. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 µm respectively. Furthermore, 33% of the magnetite (below 35 µm) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 µm with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

By J I Stewart

The Copper Canyon deposits, occur in proximity to the regionally distinctive formational boundary between the Staveley Formation and Marimo Shale. The mineralisation here is associated with breccias, veins, and alteration zones near the base of the Marimo Shale unit and in the underlying evaporitic dolomite-dololutite dominant Staveley Formation. The Marimo Shale unit, in its basal 60 metres, is highly carbonaceous and hosts ubiquitous but minor diagenetic (?) copper-pyrite, and on occasion, extensive albite-microcline alteration centres, pyritic (cobaltiferous)-quartz veins, and microcline-quartz_+plagioclase veins or veinlet arrays. The most significant mineralisation, such as at the Greenrnount prospect, consists of a shallowly dipping package of alteration zones overprinted by multiple generations of pink-orange microcline-quartz-chalcopyrite-pyrite-(arsenopyrite) and albite-calcite- phlogopite veins. Accessory mineralogies in most of these mineralisation styles consist of tourmaline, monazite, rutile, and apatite. Chalcopyrite (and secondary chalcocite) and gold are associated with each generation of alteration but are best developed in the later stages of veining. In the underlying Staveley Formation, which is a conformable transition between the Corella Formation limestones and the Marimo Shale, chalcopyrite (cobaltiferous)-pyrite mineralisation occurs as disseminations in pre- and syntectonic breccias, and with disaggregated silica pseudomorphs (after thinly bedded evaporitic sulphate beds) and associated dolomitised limestone-calcilutite. Although this mineralisation may be partly diagenetic in origin the 200 in thick evaporitic packages are also host to a locally widespread (2 to 4 km long and 200 to >500 metres wide) and pervasive 'redrock' styled microcline-dolomite¦hematite alteration. Within this gross alteration package there also seems to be a consistent association with narrow (10 to 100 metres wide), linear (stratabound) semi-massive magnetite-hematite-microcline and quartz-chalcedony replacement zones. Like much of the nearby Corella Formation the Staveley Formation, under the Marimo Shale, has undergone dissolution, paleo-solution karsting (breccias) and tectonic brecciation such that the precursor lithological details have been progressively obliterated. The post-diagenetic to post-tectonic fluid pathway development and metasomatic alteration history of this important lithostructural package of rocks has been traced from preliminary studies only. The ability to do so is largely due to the absence of significant regional and contact metamorphic overprinting, and the local preservation of precursor sediment profiles. It is proposed that both the base of the Marimo Shale and parts of the underlying evaporitic-limestone-dololutite have acted as conformable fluid pathways for hydrothermal and (perhaps) diagenetically derived, Cu-Au-(¦Co ¦As) K-Na-Ti-REE bearing, fluids and brines.

Jan 1, 1994

By D J. Bradshaw, E M. Wightman, B Newcombe

Flash flotation plays an integral role in many of the gold and sulfide mineral concentrators around the world, and yet despite this widespread use, very little information on this unit process is available in the published literature. For operations to maximise the performance of their flash flotation circuits, understanding how these cells operate, the nature of the particles they target and how to predict whether a flash flotation cell should be used on a specific ore type is of vital importance. This paper provides a summary of the key findings of a large flash flotation research project based in the operating environment of a refractory gold concentrator. The influence of key flotation performance criteria including gas dispersion, residence time and particle segregation within the cell will be discussed and recommendations for process improvements will be made throughout. The nature of the particles within the flash cell will be examined, as will the impact on the type of particles that are passed to downstream processes when the flash flotation cell is taken off-line. The development of a laboratory method to determine whether an ore is suitable to undergo the flash flotation process is also presented for its potential to aid in flow sheet development and optimisation for new ores.CITATION:Newcombe, B, Bradshaw, D J and Wightman, E M, 2012. Into the belly of the flash à Insights into the mechanisms at work within a flash flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

By Glasson K. R

The history of Ore Reserve classification and reporting in Australia is largely a history of the Australian mining industry itself. In the late 1800s, when the industry was dominated by small scale, high grade underground mines, Reserves (if estimated) were based on hand sampling and geological inference, and reporting of Reserves was either non-existent or of extremely variable quality. By the mid-20th century, the industry was dominated by large underground base metal and gold mines. Reserve estimation was coming under the control of skilled geologists and mining engineers, however Reserve classification and reporting standards continued to vary in type and quality from mine to mine. Today, large scale, low grade mining operations predominate, and Reserve estimates are generally based on extensive drilling results processed (with geological control) by computer. Through the efforts of a Joint Committee established by The Australasian Institute of Mining and Metallurgy and Australian Mining Industry Council, Reserve and Resource classification and public reporting has been standardised and controlled by adoption of the ""Australasian Code for the Reporting of Identified Mineral Resources and Ore Reserves"" released in 1989. The Code, which will continue to be modified and improved by the Joint Committee, has also been used as a basis for guides to reporting in other countries, and there is now some hope that this difficult and vexing topic may finally become subject to international standards and controls.

Jan 1, 1992

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Collier

From 1972 until 1989 when operations were suspended Bougainville Copper Limited (BCL, owned 53.58 per cent by Rio Tinto Limited) operated a large open pit mine and processing facility at Panguna on Bougainville Island, Papua New Guinea producing copper concentrate containing significant quantities of gold and silver.BCL has a stated vision of recommencing operations at Panguna. In 2008, Rio Tinto, on behalf of BCL, conducted a multi-disciplinary study to assess the technical and financial viability of redeveloping the Panguna operation. One of the key outputs of the study was a Joint Ore Reserves Committee (JORC) Code compliant mineral resource statement based on the existing block model and fundamental data, archived since mine closure. Historical data (including the resource block model and drill hole data) was recovered from computer archives by a former Panguna mine employee familiar with the various obsolete data formats, thus maintaining an unbroken chain of custody of the data by Rio Tinto since operations were suspended. No additional data were collected as part of this study.The extensive data and documentation archive facilitated a sufficiently detailed evaluation of the fundamental data and model to support an updated resource statement. Table 1 of the JORC Code was used to guide the model validation process.Reconciliation of blasthole and metallurgical plant data with the reserve model, indicated that the copper and gold drill hole composite database was significantly biased towards underestimation in several key domains due to a combination of the following: mineralisation loss during core loss, core loss (minor), vertical drill holes failing to intersect sufficient subvertical mineralised fractures and veins, drill hole spacing too wide, and variable diamond drill hole core size. The resource model evaluation was based on three material types (all previously mined at Panguna), that were defined based on cut-off grade and rock type parameters: direct feed ore – material for delivery directly to the plant, preconcentration and screening ore – subeconomic material beneficiated to produce fines of economic grade, and waste. Three pit shells and designs were generated based on three separate sets of economic parameters. These economic parameters were also used to assign material types to the block model. The three resulting models were then evaluated against the corresponding pit shells.Classification of the resource was approached conservatively due to the inherent bias in the drill hole data. Consequently only Indicated and Inferred resources were tabulated.The study highlighted the importance of maintaining detailed documentation pertaining to resource estimates and operational history, particularly reconciliation, and the value that can be added by a simple, low-cost data compilation exercise.

Aug 22, 2011

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By B Green

With a focus on safe productive tonnes, there has been an ongoing drive to increase the productivity of the mining fleet across BHP Billiton. In response, a team from the Iron Ore business was formed to review all aspects of the end-to-end drill and blast process and to challenge conventional practices that limit production efficiency. As a result of the outcomes of this work, a number of initiatives were identified to improve operational practices that have also delivered significant cost savings.One such initiative was to increase pattern size to a minimum of 1 Mt where practicable, thereby creating ‘megablast’ as a new standard across all mines. To achieve blasts of this size, the team had to overcome the complex problem of integrating wall control into the megablasts.With traditional blasting techniques, the key strategy, which is also historically inefficient but was thought to be integral to having stable, safe walls, was to utilise the trim blasting/modified production blasts technique (ie narrow blasts along the pit wall designed to ‘peel off’ the material while minimising the effects of vibration and charge confinement on wall integrity).Small traditional trim patterns comprise three to four rows of production holes and one or two rows of batter/buffer holes of reduced diameter that require the firing face to be completely exposed before blasting. This is an extremely slow process that requires a lot of resources for very little tonnage while adding additional expense to the final cost per tonne.This paper will show how the megablast approach was developed to control damaging vibration and confinement effects, flyrock and fragmentation while having the largest possible blast that includes wall control. The new practice is based on a theory that involves the initiation point and control row being the second row of holes from the pit wall itself. Adjusted charges in vented batter and buffer holes help to achieve an optimal toe design, and at the same time create a zone of broken ground that absorbs damaging vibrations formed by the attached production blast of any size, whether it is a straight wall or a multi-angled complex pit shell design.Using the new style of blasting has allowed an increase in the size of the patterns from an average of 300 kt to over 1 Mt whilst maintaining pit wall integrity. Case studies will be presented showing drill, charge and tie-in designs with the presentation having additional blast videos, including overall shots of blasts and in-close footage of what happens behind the blast at the crest of the planned catchment berm.The paper will also demonstrate the flow-on effect of using this style of blasting to reduce operational costs associated with other downstream processes, such as the reduced requirements for pattern preparation, an increase in productive digging, reduced maintenance costs and a decrease in fuel burn for equipment.CITATION:Green, B, 2015. Megablasts – enabling technologies in BHP Billiton Iron Ore, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 599–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015