Search Documents

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

Laboratory scale equipment was developed to recover zinc as oxide fume from granulated lead blast furnace slag. The cyclone furnace process is characterised by high treatment rates combined with continuous and independent operation.Results were sufficiently encouraging to warrant pilot plant scale trials being undertaken.INTRODUCTIONSince granulation of lead blast furnace slag started at Port Pirie in 1921 the stockpile of this material has increased to nearly 5 million tons which averages 17·5 per cent zinc by weight. Although a number of processes for recovering the zinc have been examined, economic considerations indicate that a slag fuming process is likely to be most suitable.In the conventional slag fuming process zinc is extracted by injecting pulverized coal and air into a molten slag bath. By maintaining a suitable air to coal ratio the oxidised zinc contained in the slag is reduced to metal. Volatilization of the zinc is followed by reoxidation in the gaseous phase with the addition of further air above the bath. The zinc oxide fume so produced is collected by normal gas cleaning methods.By examination of the thermodynamics of this process Bell, Turner, and Peters (1955) determined the zinc oxide activity of the slag over the duration of the fuming cycle.A combination of high temperature and high carbon monoxide/carbon dioxide ratio was found necessary for rapid zinc elimination.Since melting of the slag is an essential step in the slag fuming process, only two treatment methods appeared possible at Port Pirie until recently...

Jan 1, 1964

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

Tailings management trade-off studies are done for all mining projects. There is wide variability in these studies as their approach, details and outcomes are determined by the experience and focus of the project team. While some of these approaches may consider the whole life cycle of the project others may focus only on capital and operating costs and direct environmental impacts. A complete life cycle approach is not standard practice. This paper describes an approach to implementation of formalised life cycle assessment (LCA) following ISO 14044 to tailings management trade-off studies. The paper describes the implementation of the methodological framework for the LCA, ie goal and scope definition, life cycle inventory analysis, life cycle impact assessment and life cycle interpretation. This standardised approach to implementing tailings management trade-off studies following the LCA approach will contribute to the state-of-the-practice in sustainable mine development.

Jan 1, 2009

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

By A Geldenhuis, M Hagger, J Maree

Disposal of mine water is a worldwide problem occurring in the coal and gold as well in the metal ore mining areas. Since southern Africa is a (semi) arid region, mining effluents should be treated to qualities such that they can be used for agricultural purposes or that they can be discharged in river system. Studies have shown that partly treated acid mine water can be used for irrigation. A copper mine in Botswana plans to use 5 M/d of treated mine effluent for the irrigation of agricultural product. The results of this study showed that when applying the biological sulfate removal technology the produced sulfide precipitated the metals in the mine effluent, such as nickel, Zn and Mn, to metal sulfide (MeS).

Jan 1, 2003

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

INDEX OF CONTENTS.1. Historical.2. Manufacture.3. Heat Treatment.4. Fatigue, Failures.5. Consideration of the Establishment o£ a Central Testing or Proving Station.HISTORICAL.Since the introduction of improved high air pressure drilling machines in the early part of the century, efforts have been made to develop the quality of the rock drill bit, in order to take advantage of the greater increase of power output per unit weight of the machines (1). This resulted in the change from solid to hollow steel in the second decade of the present century (2).As the greatest sufferers from the dread disease of silicosis (3), it seemed appropriate that the South African gold mines should be the first to use hollow drill steel. Since then solid drills have become practically obsolete for mining purposes.Water is used with hollow steel drills not only to keep the cutting end cool, but also to assist in preventing the formation of undue dust during drilling. It is of interest to note, however, that water fed through hollow steel or sprayed into the air is only partially effective in removing fine dust particles a few microns in diameter, which particles are said to be the most potent in producing silicosis (3a).So far as the composition of "straight" carbon steel drills is concerned, a commission appointed by the Johannesburg mines carried out a very exhaustive series of tests on drill steels.These drills were manufactured from steel made by all the standard methods, including Swedish, Bessemer, crucible, openhearth, and, to a limited extent, electric furnace steel. It should be remembered that the commissioners' report was issued in 1913, when hollow drill steel had not yet been introduced. Only solid steel drills were then in use.

Jan 1, 1947

By G B. Smith, G M. Marshall, A Querzoli

The South Australian mining regulatory framework has adopted a performance based approach to the management of risk. This approach has been in place in South Australia for more than 10 years and is increasingly being implemented in mining jurisdictions in Australia and around the world. Performance based regulation focuses on setting appropriate environmental outcomes to be achieved based on an assessment of the potential impacts associated with the development, operation and closure of mining projects. Measurable compliance criteria, including completion criteria, are set to demonstrate achievement of the outcomes. It is the responsibility of the proponent to propose designs and strategies that will achieve the regulated environmental outcomes and to demonstrate the implementation of their designs and strategies will achieve the outcomes into the future. Tailings Storage Facilities (TSFs) are significant elements of many major mines and each is unique with site specific factors such a materials to be stored, design, size, location, climate, sensitive receptors, operating history of the facility (i.e. changes to design), site culture and company capability amongst a range of other factors. Consequently a fit-for purpose approach is a key principle of best practice regulation of tailings management as it takes the site specific factors into account in setting appropriate outcomes for mitigating the identified impacts associated with a proposed development. Achievement of those outcomes through fit-for purpose, well designed management strategies would ensure safe, stable and economic storage of tailings in a manner that complies with all legislative requirements and presents negligible public health and safety risks. Tailings storage must also have acceptably low social and environmental impacts, both on and off site, during operation and indefinitely post closure. Achievement of environmental outcomes during operations and at mine completion can then be demonstrated to the regulator and community through public reporting of compliance with measurement criteria which establish the appropriate level of impact for each individual operation. A number of new mining proposals including tailings storage facilities (TSF) have recently been assessed and approved in South Australia. The location, size, design, sensitive receptors, public interest and therefore risk profiles of these TSF’s have varied substantially between these new mining proposals. These considerations were reflected in the assessment of the TSFs and the resulting mining lease conditions of approval including the environmental outcomes to be achieved over the life of the facilities. This paper and the accompanying presentation will provide case studies of recently approved TSFs within South Australia and the regulatory framework for each case.CITATION:Smith, G B, Querzoli, A and Marshall, G M, 2018. Tailings regulation – a South Australian perspective, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 166–177 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By K Evtiminova, G Jobson, M Nolte, S Meik

Chelopech Mining EAD (CMEAD) is a wholly owned subsidiary of Dundee Precious Metals Inc (DPM) and operates the Chelopech underground mine and processing facility located in Bulgaria. The final product sold is a flotation concentrate containing copper minerals with associated gold and silver. The increase in production from 0.6 to 1.0 Mt/a by 2009 occurred with the original (1975) secondary/tertiary crushing, and primary/secondary ball mill circuits. As part of the mine/mill upgrade project to 2.0 Mt/a, a new single stage semi-autogenous (SAG) mill and ancillary equipment was installed, replacing the original circuits, with commissioning occurring during the first half of 2011. Aspects of the design, commissioning and operation of the new comminution facility are the subjects of this paper.An extensive program of comminution characterisation test work was completed in 2004/2005, which indicated moderate hardness and competency characteristics. The characteristics were considered suitable for a range of comminution approaches which were assessed with respect to power requirements and capital and operating costs. Retention of the existing primary crushing facility, and installation of a new single stage SAG mill located within the existing mill building, was selected as the design for the expansion.An extended ramp-up schedule for the overall concentrator upgrade turned out to be necessary as the comminution and flotation circuits were completed prior to several downstream unit processes (concentrate filtration and tailings thickening), which were required to reach the design mill feed throughput rate on a sustainable basis. This resulted in the opportunity to gradually increase the SAG mill ball charge as necessary, to obtain the throughput corresponding to the various downstream processing constraints.A relatively fine cyclone overflow stream particle size distribution is a feature of the Chelopech comminution circuit that has not been fully overcome with increasing ball charge conditions. However, design throughput has been met even under the finer product size conditions and will be consistently achieved following the commissioning of two further process improvement projects scheduled for late 2012.CITATION:Jobson, G, Nolte, M, Evtiminova, K and Meik, S, 2012. The modernisation and upgrade of concentrator operations at the Chelopech Mine, Bulgaria - Design, installation and operation of the 250 tonnes per hour comminution circuit, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P Aspinall

Safe work Australia (SWA) has a number of proposed amendments to existing Workplace Exposure Standard (WES) values that may dramatically change how mining workplaces using personal gas monitoring instruments will operate. In consultation with leading gas monitor manufacturers and distributors, an assessment of common Australian alarm settings values and analysis of potential frequency of increased alarm likelihoods has been conducted. This assessment explores the relationships between current monitoring practices, using instruments as health and not just safety tools and identify what will be needed to minimise worker ‘alarm fatigue’ and for common tasks to continue safely. This paper provides the necessary information to aid industry and hygienists to be ‘future ready’ given the likely impact that order of magnitude reductions in time weighted average (TWA) values for NO2, SO2, H2S and other common gases will have on current working practices. Reductions to gas alarm values will provide significant challenges to existing work methods and will require, practical application of the pending future values. Improvements and awareness of instrument capabilities by safety and hygiene professionals will better utilise gas monitors real-time data monitoring capacity and no longer be just ‘safe or not-safe’ instruments. The presentation seeks to promote the practical steps required in setting alarms based on risk consequence and likelihood, increase general awareness of the tools and data available in modern instruments and will enable industry professionals to better manage the challenges of any potential future changes.

Apr 16, 2024

The Pongkor Gold Mine employs 678 staff. The mine is owned by the Indonesian state company PT Antam Tbk and is located 100 kilometres south west of Jakarta, in Java, Indonesia. Mine and infrastructure development started in 1992 following intensive geological exploration over 15 years. First gold production was in June 1994. The mine comprises three main orebodies: Ciguha, which is nearly mined out, dips at 75¦ from surface to 150 m. Kubang Cicau, dipping at 80¦ from surface to 230 m, and averages 3.5 metres thick at a grade of 10 g/t Au and 128 g/t Ag; and Ciurug, dipping at 60¦ from surface to 300 m and averages eight metres thick at a grade of 14 g/t Au and 172 g/t Ag. Present global ore reserves are 4.6 million tons at a grade of 12.3 g/t Au and 133.6 g/t Ag. Exploration is continuing for new veins. Initial mining was by manual cut and hydraulic fill at Ciguha, followed by Kubang Cicau. In 1996, it was proposed to convert Ciurug to a mechanised cut and fill operation. Two single boom jumbos and three load-haul-dumps (LHDs) were purchased with the assistance of a gold loan from NM Rothschild and Sons. Implementation of this upgrade was delayed by both a national economic crisis and an invasion of the concession by illegal miners. It was not until May 1999 that raise bore vent rises and access drift infrastructure commenced. Major underground development started in 2000 and is continuing. Production cut and waste fill stoping started in July 2001. The change from manual to mechanised methods has required a total change in work practices and attitudes. However, the process has resulted in a production increase from 600 tpd to 1200 tpd. A three-month compliance test (a condition of the financing loan) was successfully completed, from July to September 2001, with an average production of 700 tpd at Ciurug and 500 tpd from Kubang Cicau.

Jan 1, 2002

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By R P. Bewick

Many future and current block and panel caves extract ore from veined rock masses. These rock masses are composed of open joints forming blocks or rock with healed networks of veinlets. These two types of discontinuities pose a challenge for rock mass characterisation and classification due to difficulties in distinguishing actually open joints from healed but weak veins when diamond core drilling and excavation blasting practices disturb the rock mass. The inability of separating characteristics of open joints and healed veins has often resulted in an underestimation of the rock mass quality and as a consequence led to inappropriate assessments of rock mass response to mining (ie rock mass behaviour) and consequently deficient excavation stability assessments and ground support designs. In this paper, guidelines are provided to improve the characterisation and classification of veined rock masses. It is shown how veined rock masses can be mischaracterised resulting in often incorrect forecasting of rock mass behaviour. Following this, the classification of veined rock masses is examined. It is shown how the primary classification systems (ie Q – Barton, Lien and Lunde, 1974; rock mass rating (RMR) – Bieniawski, 1976) may not lead to reliable ratings in veined rock masses if care is not taken to differentiate between open joints and veins of varying strength. Examples are provided to illustrate how the Q and RMR systems are insensitive to veining. Finally, an example of characterising a veined rock mass for design purposes is presented.CITATION:Bewick, R P and Kaiser, P K, 2016. Characterisation and classification of veined rocks for rock mass behaviour assessment, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 825–834 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M R. Drumond

The present work presents a new theoretical interpretation of the flotation process, which can also be applied to other mineral processing physical unit operations. This interpretation is part of the æModelo OperacionalÆ (Operational Model) that was developed as an attempt to establish a new theoretical basis for mineral processing unit operations. In the case of flotation, a book was edited by one of the authors in Brazil (Mass Concentration by Froth Flotation, in Portuguese and Spanish).The model establishes a link between a natural phenomenon (migration of particles from the pulp to the froth) and a real industrial phenomenon (mass concentration by operational interference). In this model, flotation is viewed as a phenomenon of macromolecular mass transport (of particles) between froth and slurry phases. Mechanisms for mass transport and particle flow between phases as a function of the hydrophobic potential in each phase are discussed. By establishing the so-called equilibrium distribution curve between phases it is possible to calculate macroscopic balances that are related to metallurgical results, which in turn are a function of the operational line that is required by the process itself. The number of cleaning stages and their efficiencies can also be determined by simple laboratory-scale experiments.

Jan 1, 2005

By K Knorr, S Birch

The mineralogy of new certified-reference-materials (CRM) for X-ray fluorescence from Western Australia (ASCRM 030 to 035) was analysed by X-ray diffraction using the BRUKER energy dispersive one-dimensional detector LYNXEYE-XE. The samples were studied using standard-less quantitative phase analysis, based on the Rietveld method. This method delivers the relative amount of crystalline phases. All materials were found to be high-grade iron ore predominantly consisting of hematite and goethite and very low amounts of magnetite. In addition, the gangue mineralogy was characterised. It consists of low-per cent amounts of carbonate (siderite/calcite), quartz, kaolinite, chlorite and gibbsite.Furthermore, all samples were analysed with the external standard method. This is an elegant way to probe for amorphous content without adding an internal standard. All six samples were found to contain up to 16 per cent amorphous or nano-crystalline material.CITATION:Knorr, K and Birch, S, 2013. Mineralogy of new Australian x-ray fluorescence standards, in Proceedings Iron Ore 2013 , pp 269-274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and SnAg deposits ofBolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolome, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolome area.

Jan 1, 1995

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023