Search Documents

Good morning ladies and gentlemen, and may I thank you for inviting me once again to address your conference. I would first like to welcome you all, especially international delegates and conference speakers. ItÆs a pleasure to be with you all and I hope that you have the time to enjoy the many beautiful sights that the Coromandel and Bay of Plenty have to offer.   Holding your conference in Waihi is particularly apt, especially bearing in mind the conference theme û 'Mining in the Community'. There can be few venues in the world that can boast a world class gold deposit of the likes of Martha Hill located right here in the centre of a rural service town. ItÆs a deposit that has a mining history active now in its third century and that to date has yielded some 7.5 million ounces of gold and 50 million ounces of silver. I doubt that when John McCombie and Robert Lee discovered gold at Martha Hill in 1878 that they had any inkling that their endeavours would be the foundation for a mine that would become such an inseparable part of the economic and social fabric of Waihi for the next 130 years.   This is now my fifth appearance at a New Zealand minerals conference, I especially value such occasions as it allows me to comment on your industryÆs performance over the past year, share my thoughts on matters affecting your industry, and also to give you some feedback from central government.

Jan 1, 2006

By P J. Terbrugge

The concept of vertical pit mining has been developed as an alternative mining method for the exploitation from surface of small, vertical or near-vertical, massive orebodies down to depths of some 200 m, where ore extraction from conventional open pit excavations is rendered uneconomic due to high associated waste:ore mining ratio. Systematic lateral support maintains vertical pit sides, thereby minimising waste mining volumes. Stability analysis techniques have been developed for design of this lateral support, with the support quantum, primarily comprising long cable anchors, dependent upon country rock strength characteristics and pit configuration. Where the cost of support is less than the cost of the comparable conventional pit waste excavation, vertical pit mining becomes an economically viable alternative, additionally providing the benefit of reduced environmental impact and rehabilitation requirements for the mining area. The technique has been successfully applied for the mining of a chrome deposit in Zimbabwe to an 80 m depth, believed to be unique in the world, and a full feasibilty study for a 3000 m2 diamond pipe has been carried out for mining to 200 m depth.

Jan 1, 2000

By S Vink, A Wolhuter

Increasingly the community and government regulators are calling for æzero dischargeÆ mines. Some mining companies are beginning to explore ways in which they can transition to zero discharge. When striving to attain zero discharge, mines must consider multiple variables in addition to water quantity. These include climate regime, water quality and regional water budgets. This paper explores the drivers behind the concept of zero discharge mines and will use examples to illustrate the feasibility of attaining this goal.CITATION:Wolhuter, A and Vink, S, 2013. Is zero discharge a viable or useful concept in mine water management?, in Proceedings Water in Mining 2013 , pp 329-334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By P J. Ellen

The selection of the ore haulage system is a key decision made in the development of an underground mine. The haulage system is one of the components that define a mineÆs ability to respond to changes in mining inventory and market conditions. The complexity of this decision for Telfer Deeps was affected by the realisation during the feasibility process that the true scale of the potential underground mineralisation at Telfer was still to be quantified. This paper provides an overview of the process used in the Telfer Project Feasibility Study to select an ore haulage system for Telfer Deeps. The purpose is to highlight the value of impartially approaching tasks of this type with a robust process. The process should be able to respond to issues identified as the task progresses towards the objective of finding the best solution for an ore haulage system for the mine. For Telfer Deeps, this process resulted in the selection of a haulage system built around a shaft. The systems considered during the feasibility are discussed and the components of the haulage system constructed for Telfer Deeps are described.

Jan 1, 2005

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P Holtham, K Duffy, L Pyle, W Valery

The mining industry is becoming increasingly focused on pre-concentration due to its potential economic and environmental benefits, particularly for the more complex, low-grade, high throughput operations now being developed. Advances in technology have seen bulk ore sorting (BOS) trialled at several operations. However, BOS should not be seen as a ‘silver bullet’, it can offer significant benefits, but only under the right conditions. Deposits with interspersed mineralogy or disseminated, fine-grained minerals can be difficult for BOS. Large batches of barren or low-grade material are required for BOS to be effective. Hatch has recently completed several studies for clients who believed that bulk sorting was the most suitable pre-concentration technique for their operation, based only on an assumed sorter recovery or on laboratory trials of the chosen sensor. However, minimal consideration had been given to the heterogeneity of the deposit, the achievable separation batch size or sensor repeatability. Evaluation of BOS needs to consider both heterogeneity and sensor suitability. The valuable or gangue mineral must be present in such a way that it can be separated effectively in the large bulk sorting batch sizes, without competing minerals or changing ore characteristics affecting the metal upgrade or recovery. Also, the sensor chosen must be able to detect either the valuable mineral, a proxy for the valuable mineral, or a gangue mineral for rejection with sufficient accuracy and precision (repeatability). This paper presents three recent case studies, emphasizing markers which indicated that bulk sorting was unsuitable for the project whilst highlighting the pre-concentration technologies which were applicable (including particle sorting, and coarse particle gravity separation). The modelling methodology, equipment sizing and forward work plans developed to verify these alternative solutions are also presented, demonstrating the key factors contributing to a thorough scoping assessment.

Aug 24, 2022

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By Gerasimenko MP

The authors consider the features and advantages of a new promising trend in mineral processing - column flotation. Design aerohydrodynamic and process characteristics of pilot-scale columns are studied. Optimum process parameters for various ores and operations are studied. Flow patterns in cells of various cross-sections are investigated and the relationship between Peclet criterion and specific capacity of cell is determined. On this basis options were developed for optimisation of hydrodynamic characteristics of large capacity cells, including longitudinal sectionalising of the collection zone. It is shown that advantages of high column cells (10 - 13 m) produced in the West can be implemented in a sectionalised machine of smaller height (5 - 6 m). Investigations on the influence of slurry and air bubbles flow patterns indicated that to increase flotation rate of particles of various flotabilities it is expedient to combine co- and counter-current flows of phases in a single column. The proposed designs allow tailings to repeatedly return tailings to the collection zone and alternate co- and counter-current slurry and air flows. For the first time columns with alternating slurry flows (combination of co- and counter-current flows) are developed and commercialised. Unique multi-sectional cells having a number of essential advantages compared to monocells are developed. Design features of the cell allow: implementation of different flotation process flowsheets in a single unit, improved beneficiation process results, reduced specific power requirement, and elimination of sludging of the aerator and cell bottom part. Operational problems restricting introduction of column cells are connected with the aeration unit. The new cells are supplied with pneumohydraulic and stepped airlift spargers, allowing control of bubble size distribution with a service life of not less than three years. Successful operation of the new generation of columns with cell volumes of 15, 25, 40, and 80 cu m and the height of 5 - 6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants in this country illustrated their considerable process and operational advantages and verified the proposed options and relationships. A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calculating the design of commercial-scale columns is developed.

Jan 1, 1993

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

The homologous series of saturated fatty acids investigated in this study generally show a steady gradation of properties with chain length. The solution pKa values were assumed constant at 4.9, however reported pKa values could be lower or higher. Hematite flotation response and surface pressure for aqueous solutions of these fatty acids were measured as a function of pH. For the shorter chain fatty acids, the undissociated acid was shown to be the predominant surface active species with flotation, supplemented by the physical adsorption of acid anions as the chain length increased. The reduced solubility of the longer fatty acid carbon chains made these reagents ineffective as flotation agents. The maximum flotation response of hematite using tetradecanoic acid corresponded with the precipitation edge of the reagent. The results show that the values of surface pressure of the surfactants are not always a good indication of their effectiveness as flotation collectors.

Jan 1, 2005

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By S Coward, S Jackson, S Moayer, J E. Vann

The variability and uncertainty of mineralisation, coupled with subsequent uncertainty in mining and processing, is often paid scant regard or overlooked during the evaluation of mining projects. In many instances, when the project transitions to the operational phase, the reality of feed or product variability and the consequences of unquantified uncertainties throughout the value chain become obvious. The outcome is the familiar picture of frequent ramp-up underperformance and failure to deliver on planned targets and objectives.Both mine and exploration geologists are expected to generate mineral deposit models that are based on an integration of diverse sources of data. These multifaceted deposit models already play a pivotal role in the design, development and optimisation of mining project value, and the trend to a fully digitally engineered future means that this importance is increasing. It is therefore vitally important that tools be made available to the geologist (as well as mining engineers and metallurgists) that enable them to characterise and assess variability and uncertainty via appropriate deposit models and thus articulate their impact on potential project configurations and decisions. Scenario-based project evaluation (SBPE) provides a framework for full and proper analysis of the downstream impacts of inherent deposit variability and uncertainty on project performance.SBPE has been developed by the authors over several years and aims to propagate geological uncertainty and variability through the mining value chain. The outcomes of SBPE can be tested against future external scenarios capturing financial, economic and socio-political factors that also drive project performance. Stochastic representations of the orebody (via conditional simulation (see Chilès and Delfiner, 1999)) that explicitly incorporate variability and represent uncertainty are propagated through the value chain on a block-by-block basis (ie on a much more granular basis than traditional project evaluation approaches).Conventionally, metallurgical processes are modelled with deterministic equations (eg regression models) based on limited data. The SBPE approach allows for the modelling of process performance uncertainty using geometallurgical sampling fully. Multiple outcomes of SBPE are passed through financial modelling, which can also incorporate stochastic components, thus allowing full quantification of the risks and opportunities of a set of project alternatives. The value of the SBPE system is that once a base case has been established, multiple engineered alternatives coupled with external scenarios are easily evaluated and compared in terms of incremental value.A new case study of SBPE is presented that shows how, by analysis of the various aspects of variability and uncertainty, project managers are able to focus on the areas that have the greatest ability to reduce risk and/or add significant value. This can lead to sufficient flexibility being built into operations that allow operators to cope with the real orebody delivered to the plant.CITATION:Jackson, S, Vann, J E, Coward, S and Moayer, S, 2014. Scenario-based project evaluation – full mineral value chain stochastic simulation to evaluate development and operational alternatives, in Proceedings Ninth International Mining Geology Conference 2014 , pp 21–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

The latent conditions clause in various general conditions of contract have traditionally proved to be a source of significant disputes in tunnelling contracts, even when extensive geotechnical investigations have been carried out at the tunnel site and a report of these investigations provided with the tender documents, informing the contractor of the nature and extent of subsurface conditions likely to be met with during execution of the works. This paper discusses the contractual aspects of the new latent conditions clause in the recent Australian Standard AS 2124-1986, General Conditions of Contract, in relation to tunnelling contracts. A comparison of this new clause is made with other latent conditions clauses in general conditions of contract in use in Australia and other commonwealth countries. It is seen that the new latent conditions clause in the recent Australian Standard 2124-1986 has, by providing for a reasonable apportionment of risks, attempted to minimize contractual disputes relating to latent conditions in tunnelling contracts and to provide a satisfactory basis for quick and efficient settlement of such disputes should they arise during execution of these contracts.

Jan 1, 1987

Approximation of Surface Area of Fines in Blast Induced Fragmentation The surface area of fragmentation, especially in the finer size fractions, is a useful property to characterise the mechanisms of rock breakage. In the past, researchers have made assumptions with regard to the shape of fragments in order to estimate surface area, such as that all fragments are the same shape or all fragments are spheres. Often these assumptions were developed with inappropriate measures and returned considerable variability and error for the calculation of surface area. This paper reports a model to estimate fragmentation surface area from sieve sized raw data and a density measurement, with experimental validation down to a size fraction of -45 + 38 ?m in a range of rock types. After characterisation of particle shape, a range of fragment shapes was found to be in each size fraction. Nevertheless, in the ?2 sieve series the average fragment mass, volume and the size fraction standard deviations could be predicted reasonably accurately. Ellipsoid geometry was used to describe particle shape. Using these parameters and the number of fragments (also predicted) in each sieve size the individual surface area of each fragment was simulated.

Sep 13, 2010

By S Doudle

The Iluka Resources Ltd Jacinth-Ambrosia heavy mineral sand mine (South Australia) is located in an undisturbed semi-arid landscape consisting of sparse trees, shrubs and grasses. The soil interspaces are covered with biocrusts, a living soil cover also found worldwide in arid regions. Biocrusts are composed of lichens, cyanobacteria, algae, mosses, liverworts, fungi and bacteria, and live on and within the first few millimetres of the soil surface. Biocrust organisms bind soil particles, sequester carbon and many fix atmospheric nitrogen making them important structural and functional components of ecosystems. Despite their important role in ecological processes, biocrusts are susceptible to disturbance; nevertheless they can recover provided sufficient inoculum is present. Cyanobacteria are the early colonisers and they capture atmospheric and landscape resources and establish conditions that subsequent successional seres can capitalise on. Research conducted in countries including China, Spain and South Africa has been focused on methods to either encourage rapid regeneration of cyanobacterial remnants or to introduce new material from cultured cyanobacteria. We have been investigating the extent and diversity of biocrusts across the 4500 ha mine lease and their potential to improve mining rehabilitation outcomes. Approximately 46 per cent of the soil surfaces are colonised with biocrusts and 33 taxa have been identified. Laboratory experiments were designed to mimic massive soil disturbance and treated with a range of water qualities. Within 22 days, treatments irrigated with fresh water were colonised by new cyanobacterial filaments with a mean surface coverage of 65 per cent. Secondary tests revealed that differences in the photosynthetic yield of the crust were dependent on the salinity levels of the irrigation water used. In 2011 this program is expanding from the laboratory into field scale trials designed to assess both the potential and practicalities of up scaling these techniques to provide crushed biocrusts and cyanobacterial bio-inoculum for use in mine rehabilitation.

Oct 5, 2011

By P Wood

Loy Yang Power (LYP) owns and operates a 2160 MW brown coal fired, base load power station in the Latrobe Valley, Victoria, Australia (Loy Yang A). It also owns and operates a brown coal mine that supplies fuel to its own power station and a nearby 1000 MW power station owned by International Power (LoyYang B). The mine supplies 32 Mt of coal per annum from an open pit, which is currently about 4 km long by 2 km wide and 180 m deep. LYP has 500 employees and a substantial amount of work is also carried out by contractors and consultants. GHD Pty Ltd(GHD) has been contracted to provide mine planning and earth sciences expertise. GHD is an international professional services company that operates globally in many market sectors including mining, industry and the environment. The company has major offices in Melbourne and also within the Latrobe Valley. This paper sets out the experiences that GHD and LYP have gained in establishing a unique alliance arrangement for GHD to provide a range of mine planning, earth science, dam surveillance and environmental services to LYP. The underlying philosophy of the alliance is to closely align the objectives of the two companies such that GHDÆs recompense for service delivery is proportional to the benefit achieved by LYPÆs business. Quality of service, whole of life costs and risk management are important aspects and are reflected in key performance indicators against which GHDÆs performance is measured. Currently GHD provide 20 000 hours of labour to LYP per annum, which are delivered by up to 120 staff who possess the required diversity of skills. The paper explains how the contract was initially let as a conventional service agreement and explains why the contract was transformed into an alliance. It then illustrates the operation of the alliance with reference to the 2006 work program. The paper concludes with thoughts on how the arrangement can be further developed for the future to the benefit of both parties.

Jan 1, 2006

The drill steel' sharpening shop, which stands adjacent to the Chaffers shaft, is built to the dimensions of 110 ft. 9 in. by 58 ft. wide, and is air conditioned in order to maintain reasonable working conditions during the summer months.Figure 1 is a plan of the shop, showing the disposition of the machines and equipment.LIST OF STEEL SHOP EQUIPMENTAir Conditioning Plant comprising:-1 Spray and Eliminator Type Air Cooler, 6' ft. x 7 ft. x 6 ft. with 80 fine sprays.1 No. 36 Keith type ER. Ball Bearing upcast multivane centrifugal fan.20,000 cfm. a in. WG. at 450 r.p.m.Fan motor, A.G.E. S.C. 10 h.p. 1,160 r.p.m.1 Water Pump. 2?!-3-in. Thompson Class G. Single Stage Centrifugal Pump.1 Pump Motor, A.G.E. S.C. 70 h.p. 1,160 r.p.m.Drill Steel Sharpening Equipment:-2 Holman Sharpening Machines, No. 11.1 Ingersoll Rand Sharpening Machine, No. 54.5 Ingersoll Rand Sharpening Machines, No. 50.2 Holman Hot Millers, Type DM. Double Spindle Machines.2 Morgan Hot Millers, Type 1.6 Reamers consisting of motors with Ingersoll Rand Chuck fitted to the shaft and carrying a reamer of i-in. square Ultra Capital Steel Motors, A.G.E. S.C. 1 h.p. 1,160 r.p.m.4 Double-sided Drill Sharpening Furnaces, oil fired with L.P. "Major" 2-in. non-rotary whirl type burners.Combustion Chamber, 2 ft. 4 in. x 6 in. x 12 in. Oil consumption, 3·3 to 3·8 gallons per hour.Furnace Lining, Standard Kyanite.Firebricks, 9 in. x 3 in. x 4 in.2 Moving Frame type double-sided tip hardening furnaces, oil fired using High Pressure Air reduced to 3 lb. per square inch.Combustion Chamber, 3 ft. 5 in. x 5 in. x 16 in.Burners, "Major" L.P. 2-in. non-rotary whirl type.Oil consumption, 3·3 to 3'8 gallons per hour.Furnace lining-bottom and sides, 60 only 9 in. x 3 in. x 4 in. Kyanite bricks.

Jan 1, 1941

By K Bojarska

Examination of wastes aimed at evaluation of their usefulness for utilisation needs applying modern chemical testing methods. The XRD-XRF-ICP-GC/MS set of test methods constitutes an integrated testing system enabling ecochemical examination of wastes. As far as the problem of time-consuming operations is concerned, the offered system fits in a market-oriented field of activity of accredited chemical laboratories. Within a reasonable period of time, it allows to obtain information about mineralogical and chemical properties of wastes. It provides full range of information beginning from mineral composition (XRD) through chemical composition including the number of elements and organic compounds (XRF-ICP-GC/MS) up to the contents relating to the amounts of ingredients, both organic and inorganic in the leaching tests (ICP-GC/MS). The XRD-XRF-ICP-GC/MS testing system proves to be of particular importance in obtaining reliable results enabling to perform precise assessment (from ecochemical point of view) of wastes to evaluate their usefulness for utilisation in building materials, in civil engineering and reclamation works.

Jan 1, 2003

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961