Search Documents

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By W Valery, A Jankovic

The ball mill in closed circuit with hydrocyclones is an industry standard, and well known methodologies exist for equipment sizing, selection and design. However, the potential to improve the capacity of ball mill circuits by replacing cyclones with screens has been recognised for many years and recently has been successfully realised, thanks to developments in fine screening technology. Proper methodology for equipment sizing and selection is required to capitalise on this opportunity, but there is currently insufficient information and few guidelines available on how to design such a circuit. This paper discusses the differences between ball mill circuits closed with cyclones and with screens. A methodology is described for equipment sizing and selection for a circuit closed with screens, and the laboratory testing requirements are described for low grade base metal ores and magnetite ores. An economic evaluation is also presented for a case study demonstrating the potential benefits of closing a ball mill circuit with screens.CITATION:Jankovic, A and Valery, W, 2013. Energy efficient ball mill circuit - Equipment sizing considerations, in Proceedings MetPlant 2013 , pp 285-295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By P D. Franzmann, D J. Readett, J Peterse

A better connection between laboratory- and pilot-scale test results, and heap bioleaching performance can be achieved by generating reliable information on the fundamental microbial, chemical and physical processes that occur in heaps and incorporating this information into a comprehensive and robust model. More efficient heap bioleaching, particularly of chalcopyrite, has the potential to add value to the mining industry as well as deliver attractive environmental and social benefits to the communities within which those companies operate.The results of fundamental chemical and microbiological studies of the leaching mechanism, the temperature dependence of chalcopyrite bioleaching, and the optimisation of leaching conditions are described with examples from full-scale heaps. The development and application of a number of novel techniques and tools has assisted our understanding of heap subprocesses mineralogy, hydrology, chemistry and microbiology. The heap bioleaching model HeapSim, which embodies a large number of effects not previously accounted for in other models, continues to be refined and has been applied successfully to the study of several heap bioleach systems.

Jan 1, 2004

The earth is a planet limited in size and limited in total resources. For the forseeable future, it is the only available habitat for mankind. Therefore, it follows that the more we know about our planet the better we can utilize its space and its resources for our well-being now and in the future. But, to accomplish this, we need reliable basic information. Geosciences provide such information. Recently, Dr. M. King Hubbert took note of the important effect of the geosciences on society, on how we think, and how we live. In the first century of modern geology, 1780- 1880, the influence of geology was primarily on how we think, i.e. changing our concept of the earth from one with a short catastrophic history to one that developed gradually over enormous spans of time. In the second century, 1880-1980, the emphasis was on how we live, on expanding the knowledge base so that we could more easily find and utilize the earth's resources. Now, in the third century, i.e. from 1980 towards the year 2000 and beyond, we should concentrate on both how we think and how we live; i.e. how we can better estimate potential global' resources and how we can manage these resources for maximum benefit to mankind. Like other sciences, the geosciences build upon what has already been done. Progress is achieved by using the thoughts, measurements, and observations of past workers, adding to these the insights from new experiments and from new concepts. Geology has its own methodology and approaches; but more than most sciences, it calls also upon the tools of physics, chemistry, mathematics, engineering, and biology to help solve its problems. Today's increasing population, increasing industrialization, and increasing complexity of modern society demand more detailed geoscience information so as to better use the land, reduce geological hazards, provide an inventory of resources, facilitate waste disposal, and prepare for long-term effects such as changes in climate and sea level.

Jan 1, 1986

By I Levy

At our Monkland Mine at Gympie, we operate a deep, narrow vein gold mine using hand held equipment, rail mounted haulage and narrow shafts. This is in many respects the old-fashioned way and is well suited most of the orebody geometry exposed to-date. We have also commenced some long hole stoping and we use alimaks for some jobs. The heart of our particular mining style is the employment and retention of experienced miners with remuneration based on productivity. We do our planning/monitoring/supervision down to the level of daily individual productivity. In focussing on cycles per se, we have chosen not to talk about drill and blast cycles or cycles for mine development, stope preparation or drawdown and haulage. Instead we have stepped right back from the operation as presently run and have adopted a very broad view of the mining cycle. We will in this presentation intertwine the ebb and flow of, exploration, project sponsorship, development, production and cash returns to owners. The time line considered spans both history and predicted future.

Jan 1, 1998

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By B Yang, L Wang, C Y. Ng

Flotation process intensification is often achieved through changing chemical reagent scheme or flotation machine or both, which likely brings a hefty burden to the flotation plants in terms of capital or operating expenditure. A novel approach to flotation process intensification is the use of acoustic sound, which has been demonstrated to be effective in improving the flotation of various mineral systems with different type of flotation cells. This approach was based on the dynamic stabilisation effect of acoustic sound on the flotation froth. The present work aims to understand the influence of various experimental conditions on the effectiveness of the approach. First, the effects of sound frequency and amplitude were studied with column flotation of silica particles. Results showed that the flotation performance was improved only within a certain range of frequencies and above certain amplitude. The study was then extended to the mechanical flotation of quartz particles with various size ranges and at two solids concentrations. With sound, the recoveries of different size fractions within the range of 20–212 μm were all increased. In particular, the recovery of 150–212 µm particles was increased from 0 per cent to approximately 25 per cent, demonstrating the potential for extending the upper limit of particle size in flotation by using acoustic sound. Furthermore, mechanical flotation of chalcopyrite particles at various collector dosages (50–150 g/t) was carried out with and without sound. Results showed that the increment of the final flotation recovery was increased with sound at different collector dosages. Overall, acoustic sound has the potential to be used as an effective and versatile method for flotation process intensification.

Aug 24, 2022

In both surface and underground coal mines, the detection of geological structures ahead of workings is recognised as being fundamental to the efficient operation of the mine. Mining into zones of unexpected structures has a drastic effect on a mine's productivity. For the prediction of structures, geophysical methods can be applied from the air, from the ground surface, from boreholes and from underground workings. There are several improvements to report in the geophysical methods being developed for these purposes. These include developments in three-dimensional seismic reflection surveying, cross-hole seismic reflection methods and radar systems. The recent development of the radio imaging method for use in underground mine workings will complement existing in-seam seismic methods. Geophysical techniques for use in horizontal boreholes are also under development.

Jan 1, 1988

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010

Pilot-Plant Testing of Ammoniacal-Cyanidation for Gold Recovery from Copper Gold-Bearing Ore The results of pilot-plant tested ammoniacal-cyanidation of gold recovery from copper gold-bearing ore are presented in this paper. This ore is from a deposit of Russian Federation with gold and copper grade 9.5 g/t and 0.4 per cent, respectively. Copper is largely present as malachite and azurite. The presence of chalcopyrite and bornite is also observed. In order to recover gold, gravity is recommended. Two options of ammoniacal-cyanidation using leaching of gravity tails, CIP and filtration, were tested. It was found that ammoniacal-cyanidation using filtration of leaching tailings and recycled solutions is the most optimal option. The proposed flow sheet provides for 89.7 per cent gold recovery from gravity tailings at the consumption of NaCN 0.9 kg/t and (NH4)2CO3 7.5 - 9 kg/t. Compared to conventional cyanidation, this technology decreases the consumption of sodium cyanide from 4 up to 0.9 kg/t at the same gold recovery. It can be recommended for the treatment of copper gold-bearing ores with the similar composition.

Sep 13, 2010

By Palmer DJ

Mercury is introduced into EZ's electroly tic zinc/sulphuric acid plant complex at Risdon, Tasmania, in zinc sulphide concentrate. Mercury is volatilised during the roasting operation and then distributed in the sulphuric acid plant effluents and product acid. Following an investigation of the factors determining the mercury distribution, a plan was formulated to-provide an environmentally accep- table degree of mercury containment at Risdon. This paper discusses details of the various control measures investigated and out- lines the reasons for selecting the particular procedures finally adopted for the Risdon plant.

Jan 1, 1980

By Gibbs R

The objective of this paper is to provide a broad qualitative perspective of the needs and costs of infrastructure associated with typical mining projects. Infrastructure may be defined as anything necessary for the development and operation of a project, which is peripheral to the basic extraction, handling and processing of material. As depicted in Figure 1, infrastructure acts as the link between the technological heart of a project and the outside world.

Jan 1, 1990

By P N. Duan, Z G. Liu, M S. Chu, X X. Xue, B Liu, G J. Cheng, T Jiang, J X. Liu

High-chromium vanadium-titanium magnetite has not been exploited and made full use of on a large scale so far due to the immature utilisation technology and the reality that the utilisation efficiency of valuable metals still urgently needs to be improved. In the present paper, the isothermal reduction kinetics and mechanism of high-chromium vanadium-titanium pellets were studied at 800–1100°C. The mineral composition transformation of pellets before and after reduction was analysed by means of X-ray diffraction (XRD), and the microstructures were examined by scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) to reveal the elemental distributions. The effect of reduction temperature on the volumetric swelling degree and cold crushing strength was also studied. It was found that reduction temperature has a large effect on the reduction rate of pellets, and the increase in reduction rate is more obvious in the range 1000–1100°C than 800–1000°C. The volumetric swelling degree of pellets increased with increasing reduction temperature, while the cold crushing strength decreased. The transformation of mineral species can be expressed as Fe2O3 ? Fe3O4 ? FeO ? Fe, Fe2O3·3TiO2 ? Fe3O4· (2FeO·TiO2 ) ? 2FeO· TiO2 ? FeO·TiO2, (Fe0.6Cr0.4)2O3 ? FeO· Cr2O3 ? Cr2O3 , and Fe2O3· VO/V2O3 ? VO. The apparent activation energy of the reduction reaction was calculated to be 44.3 kJ/mol, and the reduction rate is controlled by the combined effect of interfacial chemical reaction and gas diffusion through the porous product layer. The rate controlling steps were further studied by calculating the resistance percentages. The interfacial chemical reaction was found to be predominant in the initial reduction stage, with the percentage effect of gas diffusion through the porous product layer gradually increasing during reduction.CITATION:Cheng, G J, Xue, X X, Liu, J X, Liu, Z G, Chu, M S, Jiang, T, Liu, B and Duan, P N, 2015. Reduction kinetics and mechanism of pellets prepared from high-chromium vanadium-titanium magnetite concentrate, in Proceedings Iron Ore 2015, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By Dhar B. B, Gupta R. C

Grinding of iron ore is an essential step to utilise ore fines for pelletisation needed for DRI units. While preparing iron ore pellets for DRI production, the iron ore needs extensive grinding which is highly energy consuming step causing the process to become non-viable in some cases. In the present paper an attempt has been made to evaluate grinding performance of thermally treated ore compared to normal ore grinding. Such thermal pre-treatment has been found to reduce the energy requirement with lower consumption rate of grinding media. It has been observed that by applying thermal shock the ore is rendered weak with improved grindability. The stresses generated due to thermal treatment may extend existing micro-cracks in the ore and in some cases it may even nucleate fresh cracks. Experimental studies carried out on thermally treated hematitite ore reveals that the heating to 400¦C followed by water quenching can cause a reduction of 45 per cent in grinding energy. The paper gives the details of the experiment and the Results.

Jan 1, 1999

By Torres F, Cerda I, Gimenez P, Gonzalez G, Castelli L

Slurry density measurement, specially in cyclone feed streams, is fundamental to grinding circuit control. With the purpose of increasing the availability of such a measurement, the design of a soft-sensor in an actual grinding plant is addressed in this paper. The system is designed to substitute the momentary unavailability of the real density sensor, either because it has failed or because it has been removed for any other reason. The ARMAX model structure is determined using the stepwise regression method. Starting with a list of the candidate variables, the method selects, one by one, and in a systematic manner the variables which best model the measurement to be replaced, choosing them from the set of presumably correlated candidate variables. In this paper not only the single measurements are included in the list of candidates, but also combinations of such measurements having physical significance. A phenomenological model has been built with the purpose of determining these combinations. It turned out that in most of the cases the components of combined measurements having physical significance were selected by the stepwise regression method, instead of the single measurements. Actual grinding plant data is used to determine the model structure, to estimate the model parameters and to test the predictive capability of the developed soft-sensors. Good results are shown to be obtained during periods of up to 30 hours of the density soft-sensor operation.

Jan 1, 1995

By A Tinnelly

Land disturbed by alluvial gold mining should be restored to a capability or productivity as good as that which existed prior to disturbance.   Effective rehabilitation requires detailed planning prior to mining and must also be closely integrated with the mining operations.   The main constituents of a rehabilitation plan: description of existing site conditions, choice of final land use, establishment of final landform, water management and erosion control, soil reconstruction, revegetation and management of rehabilitated land are briefly described.

Jan 1, 1989