Search Documents

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

By W Potma, C Brauhart, S Halley, S Urbisinov, A Scogings

Truly integrated, quantitative, 3D GEOmetallurgical (or mineral system) characterisation, classification and 3D modelling should provide a cradle to grave unifying link across the exploration and mining value chain. All too often, spatially representative (quantitative) characterisation and modelling of a mineral system is delayed until feasibility stage, incurring a significant opportunity cost. The application of robust GEOmet characterisation methods early in the project lifecycle (at exploration stage) improves ground selection, exploration, and Mineral Resource estimation outcomes, long before there is a need for metallurgical test work. The value of this early provision of quantitative 3D mineralogy models is compounded at project feasibility stage, and continues to accrue over the entire project lifecycle, delivering cost savings, improved decision making and early warning of issues and opportunities.CITATION: Potma, W, Halley, S, Scogings, A, Urbisinov, S and Brauhart, C, 2018. Putting the ‘GEO’ back in front of GEOmetallurgy: importance of early implementation of quantitative mineral system characterisation, classification and modelling, in Proceedings Complex Orebodies Conference 2018, pp 55–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Krawcz, S Wasilewski, W Mironowicz

Barometric pressure and its variation in deep underground workings have a considerable effect on ventilation conditions. Pressure changes which create transient states of air flow and air parameters in workings are especially significant. Experiments have shown that pressure changes have a remarkable effect on air parameters at mine workings and hence, attempts to evaluate the scale of this phenomenon are of value. Continuous monitoring of the barometric pressure on the surface of mines allows for the detection of changes in pressure which undoubtedly influence alternations of pressure in the underground areas of mines. Very important factors are the internal disturbances of pressure within a mine ventilation system due to variable conditions of fan operation and the operation of a winding machine where a mine cage moving in a shaft causes piston like disturbances. Local transient disturbances caused by temporary opening/closing of air stoppings due to personnel or underground transport traffic are of importance. The results of over two years of observations of barometric pressure and its influence on pressure variation in underground mine workings are presented in this paper. The observations were possible through the installation of pressure sensors at selected points of the downcast shaft in a mine. Of interest are the observations of the transient states of pressure and other air parameters caused by emergency fan stoppage, movement of a mine cage and changes due to the opening of air stoppings. Data acquired during experiments of opening and closing air stoppings were used for the validation of a flow model in a long working.

Jan 1, 2005

By T Bednarz

The present work proposes a distributed collaborative immersive virtual reality framework for prospective applications in the mining industry. A human-centered approach is described, with people being placed in the central position and surrounded by tasks that are to be carried out. Those tasks can be then achieved through synchronous or asynchronous communication, interactions using properly constructed user interfaces, virtual and/or augmented realities and computer vision. Several examples of such arrangements are presented. One of the applications facilitates an e-learning experience by providing a very familiar object – a book – as a target for users to interact with. Importantly, this system has the potential to provide an ‘enhanced’ teaching medium, as humans tend to remember events/situations better when they experience those events in person, when the immersive factor is involved. The immersive virtual reality environment enables a user to interact physically with various 3D objects and experience behaviours, which in turn reinforces the idea that doing leads to learning. This prototype system can be implemented as an efficient and cost effective e-learning and training platform for different engineering domains. At another level, the same technology can be used in the tele-operation of mining equipment for the future mine.

Nov 22, 2011

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

By Mauk JL, McOnie A, Simmons SF

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water, whereas the mineral assemblage of replacement calcite-interstratified illite - montmorillonite- kaolinite forms a carapace and reflects formation from a C02-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

By P J. Howard, P Darvall, J H. Mainwaring

In less than a year, Atlas Iron’s Corunna Downs Project has moved from a new discovery to a substantial resource of high quality in an underexplored greenstone belt. Located approximately 170 km south-east of Port Hedland and 40 km south-west of Marble Bar, in the Pilbara Region of Western Australia, Atlas Iron Ltd (Atlas) has conducted extensive exploration work at Split Rock, Razorback, Runway and Shark Gully, consisting of geophysical surveying, field mapping, 464 reverse circulation and 16 diamond drill holes resulting in a current resource of 51 Mt at 57.3 per cent Fe (Atlas, 2014b).The Corunna Downs Project is interpreted to be hosted within the Cleaverville Formation of the Archaean Gorge Creek Group. Within the project area these rocks outcrop as subvertically dipping banded iron-formations (BIFs) and jaspilites, cherts, minor shales and meta-sediments forming a north–south trending plateau.Primary hematite-martite iron mineralisation is overprinted in the near surface environment by supergene goethite, and frequently capped with a thin laterite cover. The strongest enrichment areas have been discovered within topographic lows, proximal to fault zones, which coincide with a geophysical anolmaly. These characteristics were targeted, and the subsequent areas mapped in greater detail, allowing for efficient resource definition.Although first explored for iron in the late 1960s, it wasn’t until Atlas’ acquisition of the project in October 2012, that major strides were made to defining an economic resource. At present, Corunna Downs is Atlas’ best greenfields exploration discovery, both in terms of the potential scale of the resource and its blending capacity.The Corunna Downs prospect is emerging as a major new iron ore province in the Pilbara and includes 80 km of potential host stratigraphy. Corunna Downs sits strategically between Atlas’ Mt Webber and McPhee Creek tenements, and can play an important part in Atlas’ growth strategy as iron ore market conditions become more volatile and challenging.CITATION:Mainwaring, J H, Howard, P J and Darvall, P, 2015. Discovery of the Corunna Downs deposits, in Proceedings Iron Ore 2015, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The principal source of funding the working capital requirements of gold miners has traditionally been equity. However in the 1980s, with a substantial increase in activity in the exploration for, and the production of, gold the traditional sources of equity finance became no longer sufficient to meet demand. With the often high cost of raising equity, the need for developing alternative financing structures became critical, especially since the stockmarket crash of 1987 which at least until recently, adversely affected the amount of equity capital available for investment in mining.

Jan 1, 1994

Natural Gas has been available in New Zealand for twenty years. During that time the gas share of the energy market has grown and now natural gas forms a significant part of New Zealand's energy scene, helping consumers to achieve a higher standard of living, and reducing dependence upon imported oil. Natural gas is now used for petrochemical manufacture and power generation in addition to direct supply to consumers. As concern for the environment continues to build, natural gas will have an increasingly important role to fill in these markets. This paper sets out the background to the development of natural gas in New Zealand and identifies the current markets. It then looks at those matters which are likely to influence the role of natural gas in the 1990s.

Jan 1, 1990

By G Reynolds, L Lu

Queensland Pacific Metals (QPM) is developing its flagship Townsville Energy Chemicals Hub (TECH) facility to produce nickel and cobalt sulfates from imported high-grade nickel laterite ore for nickel-cobalt-aluminium and nickel-cobalt-manganese Li-ion batteries. The TECH facility is expected to use a patented leaching, recovery and recycling process called the DNi Process™. It uses the nitric acid leaching process for extracting nickel, cobalt and other valuable metals from laterite ore. Apart from the nickel and cobalt sulfates, the TECH Project will also produce high purity alumina, hematite (~640 ktpa) and other by-products. The hematite by-product precipitated from the DNi Process™ (hematite precipitate hereafter), is high in Fe and particularly low in impurities. QPM is working to identify potential applications for these high-purity by-products to generate additional revenue and to achieve its zero-waste ambition. As such, QPM has engaged CSIRO to evaluate various agglomeration options to produce low-cost, hematitic products suitable as ironmaking feed materials. This paper will first reveal the unique characteristics of the hematite precipitate arising from the TECH Project and then examine the sintering and pelletising processes for preparing the hematite precipitate as an ironmaking feed.

Sep 18, 2023

By T Wootton

The Barrytown ilmenite pilot plant was commissioned in two stages using Westport Titanium Project heavy mineral concentrate. The wet concentrator was commissioned on the 17 December 1989 and produced magnetic concentrate from this date.   The Drymill was commissioned on the 27 January 1990 and produced product grade ilmenite successfully from the onset.   The commissioning period was exceptionally short by normal standards and few problems were encountered. This paper concludes with general observations of operations of the pilot plant.

Jan 1, 1990

By J J. Grobler

The George Fisher Underground Mine at Mount Isa applies the long hole open stoping methodology. During the reconciliation process of transverse stopes in the George Fisher North mine it was identified that excessive underbreak was regularly experienced, with the major contribution coming from the toe area inside the stope.While over break and the resultant dilution was well investigated and well understood, limited work was done on underbreak improvement. It was decided that a re-engineering process would be followed in an attempt to improve results. The prevailing stoping practices were scrutinised and the possible causes were listed.Some of the identified causes were design, drilling accuracy, equipment condition, mucking practices and direction of firing. It was identified that in most instances the underbreak was initiated in the slot area of the stope during the first firings. Once this happened, it was impossible to get good recoveries on the rest of the stope. The slot area was carefully scrutinised and the blasting practices were changed individually.During the following two years several different strategies were trialled to increase the toe recoveries. The results indicated an overall improvement of six per cent reduction in underbreak on average, by ensuring drilling accuracy and changing the direction of firing. The economic significance of these results outweighed the time and additional work load expended to establish the cause of the problem. This paper outlines the continuous improvement process undertaken to identify and rectify the major contributing factors to the problem. It also presents a set of recommendations to be followed in order to achieve positive results.

Mar 21, 2011

By G R. Howard, G Back

Management of information systems for data collection is essential to maintain data integrity and continuity, and manage loss control on a large world-class mine such as Telfer Gold Mine. This paper aims to describe the individual systems and protocols of geological data capture at Telfer, then focus on Quality Assurance Quality Control data as an example of loss control in practice. Loss control systems are required to provide capacity, flexibility, structure and management tools to enhance data interrogation. The data that have been collected can then provide geological, financial, environmental, and contractual information to optimise management of business best practice. Telfer Gold Mine is a wholly owned and operated subsidiary of Newcrest Mining Limited. The mine is located in a remote area of NW Western Australia, and has been operating for 20 years. Geological data have been collected at Telfer since 1973. The data include drilling, assay, geological, survey, structural and geophysical data. Data management has evolved through many systems with data stored on many different hardware and software platforms. Commencing in 1995, collation, standardisation and validation of the historic data was completed. This has resulted in the first Access based drill hole database incorporating all available drilling data. This drill hole database, now hosted in SQL Server, is the hub for all geology related data management systems. The Telfer Gold Mine Geology Department has developed a series of inter-related database systems in order to manage the core geology business issues. Databases relating to drill hole planning, drill contract management, geological logging, accounting (standard costing, forecasting, invoice reconciliation), quality control (QAQC), and environment rehabilitation have all been developed to manage loss control. Management effort to provide adequate data systems and protocols has driven the system from concept to utilisation. The improved productivity, data integrity and data analysis capabilities provided by the new database systems at Telfer have allowed for greater confidence in decision making. Systems such as the drill hole and QAQC databases, when utilised in the proper manner provide up-to-date data analysis for resource audits and contract negotiations. The loss control systems are essential to maintain confidence in data integrity and hence directly effect the future of mining at Telfer.

Jan 1, 2000

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomogr`aphic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First- arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

The modern Golden Cross mine entered the production phase in January 1992. The project is designed to produce over 100 000 oz/yr of gold and over 300 000 oz/yr of silver during a mine life of eight years. An open pit and an underground mine are operated producing around 850 000 t/yr of ore, to feed a conventional carbon-in-leach processing plant. Golden Cross is owned in joint venture by Coeur Gold New Zealand Limited (80%) and Viking Mining Company Limited (20 %).   Since the start of production several major aspects of the design have altered. The underground mine began as a mechanised cut and fill operation. The cut and fill stoping progresses in 3.3 m flatback lifts with maximum stoping width of 6 m. Where the ore zone is wider than 6 m a post pillar cut and fill method is used. In 1993 a new bench mining plan was introduced between the 270 and 260 levels. Flatbacking continued in the footwall drives in anticipation of variability of the ore width and orientation. The development of levels below the main service 200 level has indicated a possibility of bulk mining the ore block rather than flatbacks. This could lower mining costs but also introduce higher dilution rates. Development is in the advanced stages for trialing this method.

Jan 1, 1994

Two events during the past decade have combined to effectively alter the role of the geologist working in Papua New Guinea. The gold boom of the 1980s resulted in a substantial increase in the general awareness at village level of mining companies, gold and landowner issues, and as a consequence of the Bougainville tragedy, landowners are also very much aware of the potential problems of a mining operation in their area. Landowners know they have the power to remove a company from a project area, and government has shown itself to be virtually powerless and unable to help the company effectively. During a considerable proportion of a project's development time, the project geologist is viewed in the eyes of the local community as the 'company'. Good landowner relationships are nurtured over a reasonable time period and the input of the geologist is significant in determining the eventual fate of company-landowner relationships. The initial impressions of the company, gathered by the local community, will have a far reaching impact on the nature and direction of their future exchanges with the company.

Jan 1, 1991

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

Geological information is essential for a diversity of public and other purposes, including land use planning, hazard mitigation, and the exploration and sustainable use of natural resources. This is especially important in New Zealand, where the complexity of the geology is due to its position on an active plate boundary - the ultimate cause of earthquakes, mountain building, subsidence and volcanic activity. The geological setting also controls the origin and distribution of New Zealand's varied mineral and energy resources. Providing information about the origin, quality and quantity of mineral resources has long been seen as a key function of national geological organisations such as the Institute of Geological and Nuclear Sciences. Such information is essential for wise land-use decisions under the Resource Management Act. One of the major goals of the Institute is to quickly and effectively disseminate research results to interested users. The most effective and internationally accepted method of presenting geological data is by means of geological maps, which show the distribution of rock types and structural features at the surface. Most countries have ongoing gelogical mapping programmes, and in recent years the need for up-to-date, reliable information has led to a trend to accelerate basic geological mapping (eg US National Geological Mapping Act 1992; Australian National Mapping Accord 1990; Plan 2000 in the UK). Over the last 25 years, the Institute of Geological and Nuclear Sciences and its predecessors (NZ Geological Survey and DSIR Geology and Geophysics) have concentrated on detailed mapping of priority areas selected on the basis of economic and scientific interest. This has included remapping of Nelson-West Coast and Coromandel, regions with high mineral potential, for which 1:63 360 or 1:50 000 maps have been prepared.

Jan 1, 1994

The efficient design of carbon-in-pulp (C.I.P.) plants involves the integration of both process engineering and design engineering.Many recently constructed plants have not recognised the above interrelationship, and as such have incurred higher capital and operating costs than were in reality necessary. This has been compounded in some cases by slavishly following the design of plants where process conditions are different for the ore characteristics in question, thus perpetuating design errors that finally become industry "accepted practice".In the paper that is to be presented the unit operations of crushing, grinding, classification, leaching, adsorption, desorption and electrowinning in C.I.P. plants will be discussed with reference to the integration of process and design engineering.

Jan 1, 1986