Search Documents

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By S Nowosad, O Langefeld

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Monger N. R

Factors leading to the decision to use Joy Continuous Miners for pillar extraction in the Burwood Colliery are outlined. A detailed description is given of the Joy 1-CM-2 Continuous Miner, including the power supply to the machine, and the method of cutting coalfrom a face. Modifications found necessary in practice are dealt with.The Joy 10 S.C. shuttle car used in conjunction with the Miner, and alterations made to this unit, are then described, together with Ancillary units for the whole installation such as transformers, motor generator set, air compressor,_ cables for power supply and water supply for dust suppression.Special arrangements were necessary to transport the Miner and Shuttle Cars through the tunnel to the Victoria Tunnel seam, and the method of overcoming the transport difficulties is discussed. Manning of the Continuous Miner unit, and final preparation andsubsequent working of the pillars is outlined. Special attention must be given to maintenance of the machines.It is concluded that the combination of Joy Continuous Miner and Shuttle Car is an excellent method for removing pillars in the Burwood Colliery.INTRODUCTIONThis paper deals with the Burwood Colliery in the RH.P. Group in which some units are engaged in the mechanical extraction of pillars with Joy Continuous Miners.In 1941, an amendment to the Coal Mines Regulation Act of N.S.W. forbade the extraction of pillars by mechanical means unless with the express permission of the Minister for Mines. As this permission was not forthcoming, no mechanical extraction of pillars took place in Australia until 1954 As it was doubtful during most of this period whether mechanical extraction would ever come about, coal generally was won with a view to maximum extraction in the first workings, thus giving rise to centre gannon bord panels and 45° angle cut throughs as shown in Fig. 1.

Jan 1, 1957

The word "optimization", refers to the search of an economic optimum, or, more precisely, to the choice of technical parameters which will define the more profitable mining project, knowing the values of the economic parameters. In fact, there is no direct way to perform this optimization, because the extremely large number of technical factors involved, from the type of working and its selectivity to the characteristics of the mill and its flexibility, makes it impossible to make a comprehensive survey of all possible projects. Beside, it would be meaningless to engage in such a task as the deposits themselves are not really known, but only estimated, with sometimes a high level of imprecision. Not to mention the numerical instability which would affect such a computation! In addition, the "best" project is not necessarily the one which strictly maximizes a given profit formula. There also exist human factors which have to be complied with, when choosing the cutoff grades for instance. Finally, there are other non-numerical factors which interfere with the choice between several projects: the shape of the bottom of a pit of the layout of the access road for instance.

Jan 1, 1986

By Budiselic C, Hefter G

The uptake of gold by activated carbon from acid chloride solutions involves the reduction of gold(IIl) to metallic gold. Deposition occurs only on the surface of the carbon at localized active sites at first, and subsequently at less active areas. The rate of uptake depends on the surface area of activated carbon, which confirms results from a recently published study (de Siegel and Soto, 1984). Increased rates of uptake were observed at higher temperatures and lower chloride concentrations due to the decreased stability of AuCI4-, the major gold(IIl) species present. Recoveries of gold approached 100 per cent for a contact time of 60 minutes at 20°C in a well stirred solution initially 5 ppm in gold(III) and containing 0.5 per cent w/v coconut-shell carbon. The presence of 0.25 Mnitric acid or 100 ppm iron(IIl) had no detectable effect on either rate or efficiency of gold uptake.

Jan 1, 1985

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004

Any engineering firm hoping to do business in the modern world must understand-and take into account-the social and economic realities of client, country, culture, and community. If these considerations are ignored, any large-scale international development project is doomed to failure even before it begins. In this changing world, the distinctions between `developed', `developing', and `less developed' nations are more and more blurred. The so-called `less-developed' and `developing' nations are rapidly acquiring technology, an educated man- agerial and technical class, manufacturing capa- bilities, a growing spectrum of developed financial and raw materials resources, and a broad range of labour skills. These nations are establishing themselves as an integral part of the modern world, on an equal footing with other nations and with justifiable expectations for an ever higher standard of living and an ever better quality of Life.

Jan 1, 1978

By A D. Wulfse, C M. D Barton

Underground fractured aquifers in the Ernest Henry deposit are to a large extent controlled by deposit scale brittle structures. The underground mine has been subdivided into nine water zones based on hydrogeological characteristics, including conductivity and connectivity, within the mining areas bound by these structures. The nine water zones and the hydrological characteristics of the associated structures are utilised for risk assessing mine development and for targeting diamond drilling dewatering activities. Wireline and conventional underground diamond drilling techniques have been used throughout the network of underground aquifers with the aim of dewatering areas within the mining footprint. These dewatering drilling campaigns have historically been highly successful at lowering aquifer water levels throughout the underground workings. As part of recent mine expansion activities, diamond drilling has intersected high pressure (>507 psi), high temperature (>50°C) and high flow water (>3 L/sec) in as yet unconstrained underground aquifers. Groundwater is typically conducted through rubble and clay rich faults, further hampering progression of drilling. Drilling through fractured aquifers at depth presents both mine planning as well as safety challenges. Recent drill holes have been delayed or abandoned when aquifers hosting this high pressure, high flow water have been intersected, risking mine planning deadlines. Recent technological innovation developed to control groundwater outflows from the diamond drill hole whilst drilling has been trialled at the Ernest Henry Mine. This case study focuses on the utilisation of alternative drill methodologies to allow the current drilling campaign to continue without delay, whilst also improving safety conditions encountered on the drill site.

Mar 22, 2022

By J Sykes, W Treasure, A Saleem, A Trench, S Ulrich, R S. Davies

Below-ground technical complexity remains a traditional source of project challenge. Above-ground challenges then augment this complexity, including in the domain of commodity marketing. All challenges must be solved to produce quality, saleable, ex-mine product. The situation is further complicated in that technical complexities are not independent of each other, so complexity is best regarded as a system rather than a series of isolated factors. Additional above-ground challenges to mining projects are also increasingly sourced from societal and environmental factors, locally and globally. These challenges not only confer project complexity, but have their source in larger, global wicked problems. Finally, financing and resourcing of projects represents an ever-present challenge for all but the highest-quality mineral deposits. CITATION: Trench, A, Davies, R S, Saleem, A, Sykes, J, Treasure, W and Ulrich, S, 2018. On the sources of complexity in contemporary and future mining projects, in Proceedings Complex Orebodies Conference 2018, pp 65–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

An automatic control system of a longwall roof support is dis-cussed. Hydraulic automatic control systems for longwall roof support have not met all requirements for such systems. Utilization of standard hydraulic elements to form a system that would-comply with all demands leads to a very complicated structure with a large number of hydraulic hoses within and between adjacent supports. So, only simplified systems have been made. This paper describes the multifunctional valve that per-mits realization of any desired logic functions, while maintaining a com-pact form, and analyses its application as a fully hydraulic automatic control system of a roof support.

Jan 1, 1985

By Johnson M, Gaudin A

With the advent of Computer aided mapping and surface modelling techniques Geologists and Engineers have had to become familiar with the capabilities and limitations of these systems to effectively use them. In this paper we will trace a short history of the rather rapid progress in this area. From this historical perspective we will make some observations and use these to guess at what the future holds. We hope that this paper will assist in clarifying the develop- ments in computer assisted mapping and modelling and promote thought on how these techniques may be best applied to the problems of the Mineral Industry.

Jan 1, 1983

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

CONTENTS:1. Introduct'iona. Previous Accountsb. Summary of Geologyc. Physiography2. Morgan Groupa. Lithologyb. Structurec. Faulting3. The Mineral Deposita. Descriptioni. Size and Shapeii. Compositioniii. Effects of Oxidationb. Relationship to Structurec. Genesis of Ored. Mount Morgan Orebodye. Sugarloaf Orebody4. Granitea. Mount Morgan Graniteb. Town Granite'c. Moonmera Granite5. Calliungal Beds6. Razorback Beds7. Acknowledgments8. References

Jan 1, 1952

By S Basu, P M. Midhun

Electro-Slag Remelting (ESR) is a process capable of producing ingots with much lower centre-line segregation and better internal soundness than conventional ingot casting processes, as well as lower inclusion and sulfur concentrations. This process is commonly used for alloyed steels intended for critical applications like components of marine turbines, supercritical powerplants and rocket motor casings. It involves melting a metal electrode using electrical resistive heating in a slag pool and re-solidification of the resulting metal droplets beneath the slag layer, forming an ingot. Conventional ESR fluxes consist primarily of CaF2, Al2O3 and CaO, along with minor concentrations of SiO2, MgO etc. The emission of fluoride vapour from the molten slag causes several environmental and health problems, triggering a need to develop and reduce the fluoride content in the ESR flux. The present study aims to develop low-CaF2 alternatives to commercial ESR fluxes without compromising on productivity and the surface quality of the refined ingot. Thus, the modification in chemical composition needs to satisfy properties like electrical resistivity, viscosity and liquidus temperature, essential for efficient ESR operation. Since electrical resistivity and viscosity are highly dependent on the ionic structure of the molten slag, it is important to understand the effect of compositional modification on the structure of the flux. The present study employs Fourier-transform infrared spectroscopy (FT-IR) and Raman spectroscopy to investigate the structural variations in the modified fluxes, especially the effect of changing SiO2 concentration, in comparison with conventional CaF2-rich fluxes. Additionally, thermal analysis (Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA)) has been carried out to characterise the melting behaviour of the fluxes. The findings are compared with simulations carried out using the FactSage™ software, ver 8.3 (GTT Technologies, Aachen, Germany). Simultaneous analysis of liquidus temperature and the structure is expected to help in identifying the practical suitability of modified ESR flux compositions for industrial implementation.

Jun 19, 2024

By D M. Menne

This paper is intended to give a general review of current gold extraction technology for free-milling or non-refractory auriferous ores. Fundamental process concepts and some of the differences between the current technologies is referred to. Typical flowsheets and layouts are provided and it is demonstrated that technology for extracting free-milling gold is relatively simple. For environmentally sensitive areas such as encountered in New Zealand relevant cyanide decay and destruction technology is also discussed. Brief mention is made of some likely future innovations. Finally reference is made of New Zealand's previous significant contribution to gold extraction technology. These contributions were pioneering ranging from the cyanide leaching of gold to adsorption by carbon and precipitation by zinc. New Zealand has not allowed its potential gold projects to develop at a rate commensurate with the rest of the world thereby stifling its renowned innovative approach in this technology. It is time for New Zealand mining to recognise its unique opportunities in developing gold extraction technology and again take a rightful place in leading the way.

Jan 1, 1986

By B L. Coulter, E Wightman, A S. Burrows

With their commitment to sustainable development in an increasingly carbon-constrained world, many resources companies are focused on reducing the energy required to create their final products. In particular, the comminution and smelting of metal-bearing ores are both highly energy-intensive processes. If resource companies can optimise the energy efficiency across these two processing stages, they can directly reduce their overall energy consumption per unit mass of metal produced and thus reduce their greenhouse gas footprint. Traditional grinding and flotation models seek to improve the efficiency of mineral processing, but they do not consider the energy used by downstream metal production, eg smelting and refining. Concentrators and smelters individually may be running efficiently, but are they optimising energy consumption of the overall system? A key step towards answering this question is to understand whether it takes less energy to remove an impurity in the concentrator or the smelter. Analysis of the complete concentrator û smelter process chain may show that there are times when the concentrator should use more energy to reduce the overall energy requirements across the mill and smelter. The new methodology discussed here will integrate downstream processing energy with mineral processing energy, to find the overall most energy efficient circuit design and operating strategy. The proposed methodology includes: determining what grade and recovery positions can be achieved in the concentrator by using different combinations and amounts of grinding and regrinding, thermodynamic calculations of the energy used to process the different concentrate grades to metal, and integrating the concentrating and smelting models to find the lowest total energy for the system. A case study which investigates the effect of increasing regrinding energy on the overall mineral processing û smelting energy consumption is presented. For the copper-nickel sulfide ore investigated the addition of regrinding results in 11 per cent less energy being used in the overall concentrator û smelter process chain per tonne of metal produced. Although regrinding is often seen as an energy-intensive process, in this case study the use of 1 kWh of energy for regrinding reduces the overall energy consumption by 12 kWh. The new mill to melt methodology will allow companies to model energy consumption from mill to smelter with a view to reducing the energy-intensity and greenhouse gas footprint of their processing and smelting operations.

Jan 1, 2009

This paper reviews the gold mining history and recent exploration activities on a number of beaches in the Catlins area of coastal South Otago. Past mining history and recent sampling indicate the presence of economically significant concentrations of placer gold, as well as anomalous PGM, and various heavy mineral species. A local source for this placer mineralisation is considered a strong possibility, along with a contribution from the Waiau River catchment via longshore drift. Blacksand beds in Jurassic sandstones of the Southland Synclinorium may represent this local source of mineralisation on the modern beaches. The possibility of placer mineralisation extending onto the inner continental shelf is also considered. Further exploratory work is justified, both for in situ Jurassic blacksand deposits, and to delineate mineralisation in the modern beach and inner shelf environment.

Jan 1, 1992

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011