Search Documents

Operations of the new copper smelter at Mount Isa commenced on the 6th February, 1953. Prior to this date a paper by R. V. Anderson (1953) outlined the smelter layout, proposed operation and expected performance.Nominally a 50-ton per day plant, output is currently at the rate of 85 long tons per day. In the first 3t years, of operation to 30th June, 1956, '71,339 tons of blister copper were produced. Operation has been stabilized' and a number of modifications to plant and operation have been made. This paper reviews the progress made to date.GENERAL LAYOUT AND EQUIPMENTThe general layout and equipment follows well-established practice as study of Figs. 1 to 4, and Appendix II will show. This diagrammatic representation of layout (Fig. 1) and flow sheet (Fig. 2) is intended for the purpose of brevity to take the place of a detailed plant description.Choice of site for the smelter was limited by the necessity for close proximity of the waste heat boilers to the powerhouse.Much excavation was necessary before foundation work commenced, but the plant is compact and further expansion is possible.CHARGE MAKE-UPRoaster charge initially comprised concentrates, purchased ores, revert materials, mine sulphide ore and barren sand. As purchased ore receipts increased and as domestic black rock oxidized ore became available, the latter two fluxes were eliminated from the charge. Fluxes at minus i-in. sizing are trucked from crushing plant or stockpile by motor lorries. Filtered mill concentrates are dropped from an overhead conveyor on to the storage patio floor adj acent to the two concentrate bins.

Jan 1, 1957

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By S C. Dominy, R C. A Minnitt

Determination of the sampling constant and liberation diameter are of importance when applying the Fundamental Sampling Error (FSE) equation to optimise sampling protocols. The method for the direct determination of the sampling constant is based on the æGy 50-pieceÆ experiment and variants thereof, which is generally known as the heterogeneity test. In the coarse gold environment, the heterogeneity test is prone to poor repeatability and bias due to the very heterogeneity that it aims to quantify. A key issue is the large sample mass that can be required in the coarse gold environment, which may reach 1 t or more. The heterogeneity test often provides an evaluation of the background gold grade heterogeneity, but understates that of the high-grade coarse-gold component. This is because the total mass of fragments is usually too small to represent the mineralisation. Despite this relatively well-known problem, heterogeneity tests are often undertaken on deposits where the presence of coarse gold is ignored, not fully realised or vastly understated. Sampling types and protocol designs are frequently based on poor quality data that do not match the characteristics of the orebody. For this style of mineralisation, an empirical approach to define ore characteristics is recommended.CITATION:Dominy, S C and Minnitt, R C A, 2012. Application of heterogeneity testing to coarse gold ores, in Proceedings Sampling 2012 , pp 143-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By T Graham

The invention of the traditional belt and idler conveyor system is attributed to Thomas Robins in 1892. This basic concept, ubiquitous in most mining operations, has not changed markedly in 125 years and still suffers from five forms of energy losses. Firstly, Wheeler, Roberts and Jones (2004) showed that indentation rolling losses, a consequence of the indentation a roller inflicts on the belt, consume 60 per cent of all energy. Secondly, Wheeler (2006) explained that bulk solid flexure resistance resulting from material interaction and movement absorbs 20 per cent. The remaining energy is lost by idler rotating resistance (5 per cent), belt flexure resistance (5 per cent) and secondary resistances (10 per cent).Traditional conveyor systems are continuous as opposed to batch systems, implying both positive and negative features. On one hand, continuous systems have high availability (available infers ‘ready to run’), but, on the other, utilisation of availability is often low; for example, when a conveyor is running empty or below capacity. This converts into reduced system OEE (overall effective efficiency). Many attempts have been made to mitigate energy losses and low OEE issues, including development of rail-based systems. The key drawbacks have been higher capital cost, low flexibility, poor availability and lack of market acceptance.A recent conceptual development known as the ‘autonomous rail conveyor’ (ARC) promises to address issues of energy loss and poor availability and provide increased flexibility by offering solutions for difficult applications. The ARC uses a series of interconnected skeletal bogies covered with a conventional conveyor belt as a load bed running on relocatable light rail. The bogeys have two axles, each driven by integrated variable speed-geared motor and brake systems, and are connected to previous/next bogeys by specialised couplers. Power is provided by a generator (located in a dedicated bogey) and ‘daisy chain’ plug in cables. Centralised redundant control is provided at a preferred point. Although the system is batch in nature, the number of carriages and trains is flexible, meaning that the system is effectively continuous. Loading is achieved by feeding the ARC from a perpendicularly oriented apron feeder, while material off-loading is accomplished by a twist-dump operation in which the belt is twisted through an angle of 50° below the horizontal, causing material to flow from the belt into a receiving conveyor.The ARC system can run multiple trains over any distance, although benefits are more significant in distances of over two kilometres. Capital and operating costs are predicted to be lower than competitive products, with planned maintenance being simple to perform.CITATION:Graham, T, 2017. The autonomous rail conveyor significantly reduces ore haulage costs, in Proceedings Iron Ore 2017, pp 467–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By B K. Da, S A. Balaji, G P. Roy, T K. Dutta

The raw material handling complex at the Durgapur steel plant provides iron ore, crushed coke and flux to two sinter plants. Either some facilities were not envisaged or not properly designed before the project stage which caused problems during operation of the plant. The absence of an in situ roll turning facility, used to increase maintenance activities for disassembly, transportation of rolls to central machine shop and assembly of rolls, led to decreased crusher availability and increased activities for the maintenance crew. The provision of a smaller vibro feeder/screen in place of a suitable sized screen caused jamming of the screen deck, adversely affecting screening efficiency and the crushing index of crushed coke. Some design modifications and developmental work was undertaken, such as the development and installation of an in situ roll turning facility in the existing limited space, achieving low feed (0.1 - 0.2 mm/rev), lower cutting speed of 30 - 40 m/minute for 350 BHN hard roll, which was also a difficult engineering challenge to bring within the tolerable limit of vibration. This was successfully achieved. Modifications to the screen deck, introduction of differential speed crushing and modification to the vibro screen and vibro feeder for uniform distribution of feed have been incorporated. These innovative design modifications to the in situ roll turning have led to a drastic decrease in maintenance activities and an improvement in the crushing index. Modifications to the screen have resulted in the elimination of jamming and improved screening. Modifications to the vibro screen before the primary crushers and to the vibro feeder before the secondary crushers have prevented excessive wear in the central portion of rolls, ultimately leading to increased roll life. Incorporation of differential speed crushing has resulted in an increased crushing index and decreased generation of micro fines. All the above modifications have led to distinct improvements in equipment availability, increased roll life and a decrease in maintenance activities and improvement in crushed coke granulametry, ultimately resulting in improved productivity and quality of iron ore agglomeration at the sinter plant. The innovative design modifications mentioned above are discussed in detail in this paper.

Jan 1, 2005

By V Morand, W R. H Ramsay

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (D1) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with D1 and the plunge of the F1 fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late D1 . d18O values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

By Jingcai Xu, Singming Gou

A sound mathematical model is an important step to predict spontaneous combustion probability so that measures against coal self-heating can be adopted in time and at comparatively low-cost. This paper analyses main factors in coal spontaneous

Jan 1, 1998

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By McDonough RJ

Mechanical agitation is the preferred system for Carbon-in-Pulp processes. Agitator design requires an understanding of the relationships between energy, shear and flow and the nature of shear rates and shear stress distribution in an agitated tank. Laser techniques are useful when studying these phenomena. The alternatives are open impeller agitation or draft tube circulation. Each has advantages and disadvantages but both require careful choice of impeller and system geometry. Overall the draft tube circulator is the more attractive in many cases. Open impeller agitators are designed in accordance with established procedures for mineral slurries taking due account of shear effects in tanks containing carbon. Preferred tank proportions are 1:1. Circulator design methods were developed in the alumina industry before being applied to CIP processes. Optimum draft tube diameter is critical to power requirements. The overall system must be designed as an axial flow pump operating in a closed circuit. Such a system exhibits quite characteristic behaviour which requires an impeller of varying pitch angle and aerofoil section for best stability and efficiency.' Tank height may be 2 or more times diameter. Resuspension of settled solids can be assisted by a series of slots in the draft tube. These slots have the secondary effect of stabilizing hydraulic behaviour and reducing installed power requirements.

Jan 1, 1982

After a five year period representing the strongest resource and commodity rally ever experienced, we are now faced with a subdued recovery following the global financial crisis. This renewed economic growth will be steady but eventually attain levels that reignite export demand out of China and other emerging nations, which are now reliant on increasing domestic demand to support their economies. This backdrop of weaker share prices and less available investment capital creates a greater imperative for company management to ensure that its share price is fully valued. The mining geologist plays an important role in achieving this outcome through direct estimation of asset value (resources) but also in strongly communicating the æupsideÆ value opportunity in both mine site and adjacent brownfields exploration and an efficient and technically sound mining operation. The contribution of mining geologists to assist in conducting analyst site visits should not be underestimated, particularly with reduced analyst coverage of the resources sector and some simplification in company analysis through ranking companies on Reserve and Resource positions.

Jan 1, 2009

E. W. Stutchbury (Internationa~ Oombustion Aust. Ltd.) : Mr. Callcott made particular mention in his paper of erosion in primary air fans which are placed after the mill discharge. He adds that subsequent reduction in plant performance and resulting increased maintenance costs occur. It is generally assumed that this statement is substantially correct as the fan handles the complete output from the mill, but with modern materials, reduction in performance and subsequent .maintenance are not now a problem. This consideration of handling the pulverised coal in the fan is more than offset by the advantage of operating the mill under suction which results in cleaner operating conditions, simpler feeder arrangements and elimination of complicated seals on the mill.and feeder unit. It should be specially noted that whereas mill exhausters in the past have used chequer plate blades (sometimes with the addition of hard facing by electrode deposit) it is modern practice to provide fan blades of up to 1 in·. thick Ni-hard suitablyheat treated, with the circumferential section of the fan also in Ni-hard. By the use of this material large power...

Jan 1, 1957

By J Dwyer, M Hill

Downer’s mining division has made an operational and financial commitment to developing engineered solutions that mitigate the risks associated with operator proximity to uncontrolled development drill boom movements, and unguarded rotating drill steels.With the potential for serious injury or fatality, these identified risks are categorised as critical. Previous attempts by the industry to engineer them out have produced limited success, with numerous incidents still occurring year on year. Ultimately, the industry (as a whole) remains reliant on procedural prevention for operator safety.Downer understood the success of such an initiative would largely depend on the effective collaboration between operational experience, technology experts and automation. With so many variables requiring consideration; such as physical operator movement, machine boom movements, variable machine positions, and underground environmental impacts – challenging traditional technologies was necessary to deliver an optimal solution.For that reason, discrete detection (similar to laser curtains or beams) was considered not fit for purpose. The use of situational mapping, using rotating lasers, however, provided the optimal solution. The lasers collect data that is then processed using a custom software application.The software application is specifically programmed for tracking and classifying objects within detection zones, using advanced algorithms and filtering. Recognition and removal of non-positive disturbances are possible without losing personnel detection capability. The detection of relevant classified objects (humans) is determined by analysis of object size, age, movement, and speed etc. When the relevant object is detected, an alarm and inhibit function is applied preventing drilling functions.Any breach of the safety zone (forward of the front jacks) will automatically disable the hydraulic boom function. This can only be reset in the cabin once the person or persons have returned past the front jacks of the development drill into the safety zone.Downer, in collaboration with partner YUMARR Automation, has successfully developed this reliable boom isolation system, and is called JumboGuard. The system has now been commissioned and installed across all Downer Mining development drill fleets, operating in Australia.CITATION:Hill, M and Dwyer, J, 2017. JumboGuard – automatic boom isolation system, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Parkhurst D. H

It is shown that a differential colorimetric technique can be used as a routine method for the estimation of titanium in beach sands, and their ore dressing products. The method will tolerate the presence of most of the other elements usually found in beach sands. The accuracy is shown to be within the limits of ±0ò31 per cent for concentrates containing more than 95 per cent titanium dioxide and ±1 per cent for tailings containing 0ò2 per cent titanium dioxide. The method is described for use with a Hilger "Spekker" absorptiometer.

Jan 1, 1957

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010