Search Documents

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Y Miyoshi, J Ishibashi

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Sea floor hydrothermal activity in the Okinawa Trough is considered a modern analog to ancient Kuroko-type volcanogenic massive sulfide (VMS) deposits. Recent scientific drilling projects at active hydrothermal fields have enabled us to conduct comparative studies on hydrothermal clay minerals between ancient and modern systems. Zonal distributions of clay minerals below the sea floor of an active hydrothermal field have been revealed, which is represented by the distinctive assemblage of clay minerals. Zone 1 consists mainly of montmorillonite and sometimes of kaolinite; Zone 2 consists of chlorite and chlorite-smectite mixed-layer mineral; and Zone 3 is represented by the co-occurrence of illite and chlorite, from shallow to deep. This zonal distribution is likely to be in accordance with that reported previously for the Kuroko-type ore deposit. Similarities are also recognised in chemical compositions of illite and chlorite, which are both abundant clay minerals in the vicinity of the ore deposit. While illite would be formed by interaction with the hydrothermal ore fluid, the formation of Mg-rich chlorite is attributed to Mg metasomatism caused by the involvement of sea water. Further studies, especially focusing on interactions between fluid and solid phases, would significantly promote our understanding of dynamic processes for the formation of VMS depositsCITATION:Ishibashi, J and Miyoshi, Y, 2015. Hydrothermal alteration process in active sea floor hydrothermal systems in the Okinawa trough, from a viewpoint of a modern analogue for the Kuroko-type volcanogenic massive sulfide deposits , in Proceedings PACRIM 2015 Congress, pp 481–486 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D A-F Batchelor

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.South-East Asia represents the world’s most productive tin province, mainly from placers. Kalimantan has been a major diamond producer, while in the 1980s a placer gold rush occurred in Indonesia and Malaysia. Reviewing extensive geological and mining data highlights phenomenal palaeo-environmental changes in the Sundaland region, interpreted to be responsible for generating ‘giant’ placers. Correlation of the Late Cainozoic stratigraphy has been facilitated from mine exposures and drill holes distributed throughout Peninsular Malaysia, the Indonesian Tin islands and Kalimantan, including contiguous marine areas with extensive shallow seismic profiling data. Knowing the association of rich placers with palaeo-environmental episodes and stratigraphical units has been helpful to facilitate their discovery. All three placer commodities responded similarly to region-wide landscape evolution following Mio-Pliocene high sea levels. Commencing with major regression, important stages comprised: a long period of landscape stability with deep weathering during the maximum Sundaland extent gradually rising sea levels/precipitation initiated slumping of mineralised regolith to form fans, later reworked by braided streams with aggradation (Old Alluvium); during episodic pluvial periods downcutting upgraded placers significant change occurred around Middle Pleistocene time with peneplanation and pedogenesis from Late Pleistocene time ‘modern’ fluviatile deposition (Young Alluvium) filled incised V-shaped valleys.Placer seams show systematic variation in stratigraphic position, in particular cassiterite especially occurs in the Old Alluvium (equivalent Upper Dahor Formation in Kalimantan). Gold is commonly richer in gravelly younger deposits, partly because of secondary precipitation within permeable alluvium. Reworked diamonds are predominantly concentrated especially in younger fluviatile alluvium.CITATION:Batchelor, D A-F, 2015. Conceptual exploration for tin, gold and diamond placer deposits in ‘Sundaland’ (Indonesia and Malaysia) by understanding the late Cainozoic stratigraphic context, in Proceedings PACRIM 2015 Congress, pp 499–506 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K Lownie, R Sani, A Sianturi

Part of the PT Freeport Indonesia (PTFI) mine production is in the process of transitioning from the deep ore zone (DOZ) mine to the deep mill level zone (DMLZ) mine. The DMLZ mine is the next lift in the caving series and lies 500 m below the current DOZ footprint.In order to reduce the need for a very expensive additional ventilation system for the DMLZ mine, it was decided to reconfigure some infrastructure and upgrade the performance of the three existing DOZ mixed flow ventilation fans in situ, reducing the new fans required to two. This was far less costly than providing complete new installations.These fans are installed in individual underground chambers in DOZ mine exhaust drifts and connected to the DMLZ mine exhaust drifts system in 7 m × 7 m airways size, through sets of 6 m diameter by 500 m high raises.The upgrade process involved replacement of motors, fan shafts and bearings. The existing 1600 kW DOZ mixed flow fans are 3500 mm diameter and operate at a speed of 595 rev/min and were originally designed to deliver 390 m3/s at 3.3 kPa. Efficiency optimisation may be required at a later date.The upgraded DMLZ fans are required to deliver 425 m3/s at 3.7 kPa and it was necessary to increase in motor size and speed to 2200 kW at 710 rev/min. This paper will discuss the fan upgrade project and in particular the integration of an unusual ventilation system, which is based on the semi parallel operation of multiple large fans.CITATION:Sani, R, Sianturi, A and Lownie, K, 2017. Operation of deep mill level zone mixed flow fans after the first fan upgrade – a parallel fans case study, in Proceedings Australian Mine Vent Conference 2017, pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By K George

The Dugald River lead-zinc-silver deposit is located approximately 60 km north-west of Cloncurry and 87 km north-east of Mount Isa. The development project is expected to turn operational in 2018. The resource is estimated to contain 61.1 Mt at 12.6 per cent zinc, 1.9 per cent lead and 34 g/t silver, with a projected mine life of 25 years. The evolution from exploration project to development project has presented multiple challenges for the technical team. Understanding and modelling the structural complexity of the deposit has been one of these challenges.Historically fault zones were logged as a lithology, with structural measurements recorded in a separate database table. When underground drill programs and development commenced in late 2012, it was recognised the deposit was more structurally complex than had been modelled. The extensive number of fault zone lithologies in core logging, made it difficult to identify fault trends and model faults in 3D software packages.In 2014, a structural project was conducted to produce a fault model for the deposit. The project highlighted that by logging the faults as a lithology, a shortage of fault characteristics was being recorded. Additionally, structural information could not be filtered to identify different fault sets due to the lack of information available to filter on. One of the major outcomes of the study was to change the methodology for the structural logging of drill core.Faults are now logged in a separate structural log. The structural log collects two types of information: interval data and point data. The interval data represents the damage zone of the fault in the surrounding rock and the point data the plane of movement for the fault. The faults are further characterised by their intensity on a scale of one to five, the type of fault structure (fault breccia, fault vein etc), the minerals present on the fault surface and structural measurements when available.The new data set allows fault data to be filtered based on fault characteristics, making implicit and explicit modelling of the faults more timely and accurate. The data set can be used to produce fault wireframes as single surfaces from the point data or hanging wall and footwall surfaces from the interval data. The logging method and how its applied in fault modelling form the focus of this paper.CITATION:George, K, 2017. A new approach to logging and modelling faults at the Dugald River Pb-Zn-Ag deposit, North West Queensland, in Proceedings Tenth International Mining Geology Conference 2017, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

A new approach to resource estimation at the exploration stage is emerging, based on the application of simple software techniques. The techniques combine the power of interactive graphics with proven database, analysis and estimation tools. With effective use of these tools the geologist now has maximum chance of deriving a reliable structural and grade model from the limited exploration data. Unlike cutoff-based polygonal methods, the resultant geological model can immediately be used to evaluate any economic scenario.These modelling techniques are embodied in MINEX-3D, an Australian software system. With the emergence of the 386-based PC and high resolution (VGA or better) graphics, MINEX-3D makes the power of this new 'desktop geological modelling' accessible to most exploration geologists.

Jan 1, 1990

By Andrew A. A, Hamilton P. J

Constraints on pore water evolution in the aquifers of a sedimentary basin may be realised through stable isotope analyses of present day waters, and their comparison with water compositions calculated to have been in isotope equilibrium with the products of diagenesis during burial. Integrated with detailed petrographic observations, and thermal, structural and stratigraphic analyses, fluid migration patterns at various stages in a basin's history can be identified. This has important implications for modelling basin hydrology, hydrocarbon distribution, and reservoir quality in the Latrobe Group, Gippsland Basin, and oil-prone successions Elsewhere.

Jan 1, 1992

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Gold was first discovered in the Shotover by Thomas Arthur in 1862. He left his job as a shearer and soon there were up to 3000 miners working over the length of the river. Some parts were extremely rich and a few early miners recovered as much as 300 ounces in a day. From these early days of hand working the operations progressed through to hydraulic elevating once water races and pipes were installed after the Skippers road was completed about 1890. The riverbed was worked in paddocks with .the gravel being sluiced to a central suction which elevated the material over a sluice box. Use of this system continued intermittently through until 1977 when Joe Schieb retired û the last of the hydraulic miners. Many bucket ladder dredges worked on the lower Shotover near Big Beach where the Sew Hoy family recovered a lot of gold. Just after 1900, at least three worked further upstream, one on the beach where Shotover Jet now operates and one further up below the Moonlight. All the sections for this were transported in over the Moonlight Track and the boiler, steam engine and bucket ladder are still sitting at the edge of the river. up near Maori Point a dredge operated from Dredge Slip upstream. Records are poor on these dredges but they all suffered from the frequent floods and large boulders which damaged the bucket line. The last dredging attempt was about 1930 when a suction dredge was constructed on Maori Beach. This failed as seems to be normal for most suction dredging ventures. The river can drop to very low levels in the middle of a dry summer, and in winter when the water is tied up in the mountains as ice and snow. During 1863 when heavy rain melted snow in the high country, the river rose 35 feet overnight and drowned many miners camped on the banks. The ever present risk of flooding dominates the method of working and plant design.

Jan 1, 1987

The efficiency of water sprays in suppressing airborne colliery dust depends on many variable factors. A survey of previous work in this field shows that swirl spray nozzles are the best dust suppressors.Investigations carried out in an experimental dust chamber show that, in spite of limitations to the application of water sprays in underground use, promising dust suppression efficiencies in mechanised mining can be obtained with swirl spray nozzles.INTRODUCTIONA dust hazard has always been associated with coal mining, and the recent growth of mechanisation has resulted in a greater production of fine coal and dust, thus increasing the hazard. A better knowledge and appreciation of the medical aspects and dust explosion factors has led to practices reducing the seriousness of the problem. However, the dust hazard still exists and its control is basically an engineering problem.Dust, as with any atmospheric pollution, may be removed from the, mine by ventilation, which is an indirect method of control. Direct methods, in which the dust is prevented from being produced and from becoming airborne, should be employed where possible. Of these direct methods the most significant is the use of water sprays.THE DUST HAZARDAn appreciation of the physical nature of the more important dust hazards is necessary before considering the removal of the hazard. The main hazards associated with colliery dusts are the health hazard and the explosion hazard. "Dust" comprises solid particles of size minus 20 mesh Tyler (833 microns).

Jan 1, 1964

By Bujtor G. J, McMahon D. W

This guide to the understanding of ore reserve estimation is the revised version of a report with a similar title circulated within the CRA Limited (CRA) group of companies in mid-1980. It is the principal result to date of an Ore Reserve Study commissioned by CRA in late 1977.This guide to the understanding of ore reserve estimationis the revised version of a report with a similar titlecirculated within the CRA Limited (CRA) group ofcompanies in mid-1980. It is the principal result to dateof an Ore Reserve Study commissioned by CRA in late1977.The study was prompted by two ore reserve situations.The Zinc Corporation and New Broken Hill Consolidated,Broken Hill, had reached the point of havingto find a replacement 'for their traditional ore reserveprocedure and Mary Kathleen had to admit publicly thatore reserve predictions would not be realized. Thesewere not however the only problems to be looked at. Asmentioned more fully later, other ore reserve situationswere known, or were met during the study, in copper,gold and nickel as well, where poor realization: expectationratios had ranged from embarrassing to disastrous.These made it clear that ore reserve estimation had to belooked at afresh.The fresh look has resulted in a broadening of theconcept of ore reserve estimation from its traditionalpurely computational basis to an approach embracingall the many things that can affect expectation andrealization as essential factors. Hence this guiderepresents a gathering together of what has been learnedand what should be known to all those concerned withore reserves in any of its diverse aspects.The study has been marked"by a number of changesof thinking. At first the aspects that appeared to requireattention were two; recognition that an ore reserve statementwas an estimate, not a precise calculation; and asearch for im improved estimation procedure adapted tolow grade ores with narrow economic margins. Threeyears later the view was that the need was to incorporateinto ore reserve estimation all relevant aspects of theproposed mining operation from choice of a samplingmethod to sales contract specifications.This study is thought to be unique in being frankabout weaknesses in ore reserve estimation and intreating failures not as natural disasters (like drought orflood, which have to be endured) but as potentiallyavoidable. It has led to three principal conclusions.

Jan 1, 1982

By Kubik K

This paper reviews the historical data on relative height changes of landmasses with respect to sea level for Pacific Rim countries.It discusses existing theories of the Greenhouse effect, and the interaction with the vertical movements of the continental plates which leads to different effects for different places. Possible future scenarios are described and directions for future research and measurement programs are given.Relative sea levels are governed not only the increase of water from deglaciation but also by a range of other factors such as variable water storage in lakes and the atmosphere, thermal expansion of the ocean, ocean currents, and the shape of the ocean and the continents. Sea floor spreading, for example, is ultimately more significant than deglaciation in sea level control but is generally much slower.

Jan 1, 1990

By Kleine T. H

Blast design involves many engineering constraints and objectives. Some of the more important include the implementation costs, the desired fragmentation and shape of the muckpile. A spreadsheet has been developed to allow blast design options such as burden, spacing, blast hole diameter, decking and explosive type to be varied. As any option is varied the spreadsheet recalculates and graphs the expected implementation costs, fragmentation and muckpile shape in seconds.The spreadsheet extends the philosophy of simple robust fragmentation prediction (Cunningham, 1983) to include similar models for explosive detonation (with respect to explosive type, age, blast hole diameter and density) and muckpile shape (with respect to burden, spacing, charge location and weight). The new empirical models for explosive detonation and muckpile shape prediction have been calibrated successfully for one situation and are now undergoing further field trials.

Jan 1, 1992

The Mineralogy and Reactivity of Pyrrhotite from Selected Nickel Ore Deposits and its Effect on Flotation Performance

Sep 13, 2010

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

By Lottrey A. L, Sowerby B. D, Cutmore N. G

On-line monitoring of low rank coal quality during input to a process has the potential to provide benefits through: ò anticipation of coal quality variations prior to utilisation; ò provision of a tool to help determine the influence of coal quality on process behaviour, and ò provide a direct measure of coal quality for pricing. Moisture and ash are the two most significant coal quality parameters for combustion. They determine the energy content which can be derived from the coal and the problems arising from the presence of ash in the process (eg ash fouling, corrosion, erosion, particulate emissions and ash disposal). Extensive pilot-scale testing and full-scale experience has shown that specific coal/ash constituents (eg Na2O/ash ratio, acid-soluble aluminium, silica, sulphur contents, etc) are also important for the behaviour of Latrobe Valley brown coal during combustion, ash formation, deposition and removal of ash in precipitators and furnace ash hoppers. This paper discusses the range of on-line analysis techniques which have been investigated and their application to low rank coal analysis. Preliminary results from a joint SECV/CSIRO project which aims to develop two separate advanced instrument systems are also presented. These systems are based on: ò microwave attenuation and phase shift - for direct determination of moisture content; and ò inelastic neutron scattering - to provide total hydrogen, carbon, chlorine and ash contents, with potential for calculation of moisture content, specific energy, sodium content and Na20/ash ratio using correlations.

Jan 1, 1992