Search Documents

By D J. Williams, G W. Wilson, S, A B. Tran

A comprehensive field program was implemented to evaluate the internal structure and hydrology of two full-scale waste rock piles. The excavation of waste rock dumps for in-pit disposal at the two mine sites provided an opportunity to characterise the in situ properties of the dumps given contrasting geologic and climatic settings. The internal structure and materials within the dumps were observed and sampled as the waste rock piles were being excavated and placed in the open pits for permanent closure. The field program was designed to fully characterise the structure and material properties of the waste rock. The alteration of the material by physical and chemical weathering was also observed. Samples were analysed for paste pH, water content, grain size distribution and geochemistry. In situ density and matric suction were also measured. Soil water characteristic curves and saturated hydraulic conductivity were measured for representative materials. These properties were used to predict seepage pathways through the waste rock and the resulting outflow geochemistry using the finite element model SEEP/W. The materials in the dump at Site 1 were predominantly fine-grained in texture and highly weathered. The presence of dipping beds with alternating coarse and fine materials was evident throughout the profile of the dump. The structure of the waste rock appears to have an impact on the hydrologic pathways within the waste rock pile. The material in the dump at Site 2 was found to be competent and resistant to particle size breakdown. The particles range in size from clay size to large boulders with the median particle size being approximately 125 mm in diameter. The coarse-grained texture of the waste rock resulted in a loosely packed arrangement of coarse particles with little matrix material infilling the pore spaces between the coarse-grained particles. Seepage modelling for Site 1 was completed to predict seepage paths based on observed structure and hydraulic properties measured in the laboratory. The modelling showed that materials with a fine grain size distribution become the dominant pathways for flow through the waste rock pile. The modelling also showed that layers with high silt and sand contents are subject to the highest flow rates. Finer grained clay rich layers have a low hydraulic conductivity and do not convey large volumes of water. Alternately, coarse gravel and cobble materials are unsaturated under values of matric suction that approach the residual water content of the material and do not transmit liquid water. The seepage modelling together with the results of the geochemical analysis show that the dominant particle size that receives the most fluid flow and flushing ranges from fine sand to silt, corresponding to materials with air entry values ranging between 5 kPa to 50 kPa.

Jan 1, 2003

By K Eglinton

The extractive industries response to community engagement due to social and political pressures in the 1980s and 1990s was the starting point of development leading to the modern function of corporate social responsibility.Challenged by communities who have greater access to information, demand greater transparency and responsibility of corporate organisations and who possess greater awareness of the communities they participate in, the mining sector faces another step change in how it approaches and integrates corporate social responsibility, transparency and engagement.Mining is seeking reserves of lower grades, in more sensitive environments and in countries with minimal transparency and governance. Not only are the locations changing but so to the stakeholders to engage with and issues to contend with. An increasingly savvy opposition, including not just the ‘green hippies’ but the Gen-Ys interested in the wider sustainability debate and Baby Boomers moving to life style environments, are now questioning mining’s behaviour and encroachment into ‘their space’. Issues including effect on lifestyle amenity, property value, energy efficiency, social provision; concepts such as ‘doing more with less’, participatory engagement, increasing transparency and balancing economic, environment, cultural and social aspects are becoming the norm.The traditional model of supporting local communities, communicating plans and providing employment, community investment and indigenous support programs is not enough. Our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities and play a role in addressing the global sustainability issues.This paper draws on corporate social responsibility trends, integrated functions and implementation approaches through the application of activities within Newmont operations across Asia Pacific.The approach presented works on the philosophy that communities do not necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Nov 22, 2011

Many operating hard-rock sulfide mines are predicted to require perpetual post-closure management to prevent environmental degradation. Causes include evaporative concentration of metals and other solutes in pit lakes, and acid rock drainage from sulfide waste-rock, tailings, and pit benches. Dilemmas posed by the prospect of perpetual management include: uncertainty in predictive models typically prevents reliable bounding on forecasts for the timing or magnitude of environmental impacts; comprehensive closure designs that can meet environmental standards may not be economically possible, particularly when applied retroactively to mines permitted under less stringent closure requirements; the publication of site-specific environmental analyses in peer-reviewed journals are discouraged in the current regulatory environment, hindering scientific advancement; and the durability of financial and government institutions cannot be assured for the long-time horizons over which mine impacts are predicted to occur. Re-evaluating mine closure in a framework of sustainable development (as proposed by the Mining Mineral Sustainable Development forum), can resolve, in part, these dilemmas. Key sustainability goals include: assurance of the social and economic well-being of the local community; assurance of the long-term environmental integrity of the region; and establishment of institutions capable of addressing (and learning from) long-term environmental management. Under a sustainability framework, impractical plans for immediate attainment of perpetually-stable closure may be replaced with a fund for long-term management of environmental impacts (eg through contaminant migration controls and exposure barriers), and a set-aside long-term growth reserve intended to eventually fund more complete closure. Fund expenditures would follow Adaptive Managementùa template for environmental-management institutions in which knowledge accumulated and uncertainty acknowledged explicitly. Under adaptive management, trusts would be flexible entities, supporting an evolving program of monitoring, predictive model refinement, and treatment. Periodic value of information analyses would target data collection efforts, refining the balance between predictable cost and uncertainty. This framework could overcome present-day financial shortcomings, enhance the field of environmental science, and meet the needs of future generations through the propagation of capita.

Jan 1, 2003

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By J T. Carswell

Best practice mine sampling should provide a detailed quantification of all potential sources of error at each stage of sampling, sample preparation and assaying.Quality assurance (QA) should include testing for and quantifying potential sampling errors, and should be the basis for establishing ongoing sampling protocols, should set error limits and define quality control (QC) procedures. QA should be within the framework of Theory of Sampling (TOS) but may not involve the estimation of the sampling constant and the application of Gy’s formula.Best practice QC should be carried out efficiently and in a timely and cost-effective manner with regular reporting against the guidelines established by QA.This paper provides an assessment of, and checklist for, current best practice sampling QA/QC with examples from operating gold mines including the QA/QC of underground (UG) reverse circulation (RC) grade control.CITATION:Carswell, J T, 2017. Best practice sampling QA/QC for gold and base metal mining – including how to assess the applicability of underground reverse circulation grade control sampling, in Proceedings Tenth International Mining Geology Conference 2017, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

With the burgeoning opportunities for new gold mines to be developed the opportunity now exists for a reassessment of the optimal processing path for these gold ores. Projects have traditionally followed the path of whole ore cyanidation with either Carbon In Pulp (CIP), Carbon In Leach (CIL) or Merrill Crowe. The challenge ahead is whether these traditional processing methods are the best option for stakeholders, or to go beyond CIP and use a combination of currently available technologies that can be used to provide gold recovery at a significantly reduced capital cost and minimal deleterious impact on the environment. Either stand alone or combinations of gravity concentration and flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. Treatment of a gravity/flotation concentrate by intensive cyanidation may be processed by the InLine Leach Reactor (ILR) developed by Gekko Systems of Australia. The advantages of the technology combining gravity/flotation followed by intensive cyanidation are significantly reduced capital costs; improved safety due to reduced cyanide inventories; the majority of tailings un-contaminated by cyanide; less energy required due to an opportunity for an increase in grind size û reducing green house gas emissions; detoxification of concentrate tailings can minimise tailings disposal and containment requirements.

Jan 1, 2004

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By P Card

“Let’s get discipline and quality into easy to understand evaluations!” Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations. Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

By D Wimpenny

Underground infrastructure is often a critical component of transportation and utility schemes. It is characterised by long design lives with limited access for inspection and maintenance. The exposure environment can be difficult to assess since it will often vary substantially between different locations in the same facility and with time during construction and in service. In addition, the specific demands placed upon underground infrastructure are not well covered by the exposure classes and other guidance given within current codes of practice. When problems occur they can be difficult to rectify and involve significant disruption.Given these substantial risks the prudent designer may adopt a systematic ‘durability planning’ approach which:· defines the environment and principal deterioration mechanisms for the various elements and construction materials,· predicts the design life for alternative durability enhancement options, and· recommends associated measures to be adopted during construction and in service.This paper describes the development of durability planning within Halcrow, giving examples of its use from its first implementation on tunnels under the Suez Canal in 1993 to recent projects in the Middle East and Australia. It seeks to demystify the process, identify shortcomings and speculate on its future development within the civil and mining sectors.

Mar 8, 2011

By N Burgio

Block cave mines are often thought of as rock factories where high volumes of production are mined from a fixed area suggesting little requirement for geological input and control. Yet caving operations have peculiar and specific technical requirements from prefeasibility through to post-mining reconciliation. Whilst essential elements such as resource definition, geological interpretation and sampling strategies are common to all mining methods, planning for a block cave requires a different emphasis and philosophical approach in how we deal with these issues. We will examine why a geoscientist’s input is critical towards the successful planning, design and monitoring of a caving operation.

Aug 22, 2011

By W Malone, J Garrett

FLSmidth (FLS) has spent the last 15 years, working with customers and engineering houses to deliver innovative improvements in crusher safety, coupled with the latest, maintenance friendly, crusher design. The key focus being to prevent service personnel from working underneath the crusher during maintenance and obviate the need for personnel to be exposed to suspended loads when performing tasks such as, main shaft installation, for example. Improvements include: full top-service capability to ensure the safest and fastest way to disassemble the crusher for maintenance purposes, which also removes the requirement for a service cart; a selfaligning main shaft which ensures remote assembly is now possible, keeping service personnel well out of harm’s way; And rotable shells, or the ability to perform relines off-station, allows for quick shell ‘swap-over’ without the downtime associated with removing, refitting and curing time associated with epoxy backing. The high flow spider improves large material entry into the crusher, reducing blockages and downtime and therefore maintains crusher capacity. Each size of crusher in the range comes with an option to increase the standard feed opening to a larger one if desired to compensate for ‘blocky’ or ‘elongated’ feed material, a common problem for Pilbara hematite iron ores. Power capability has also been increased with a maximum of 1500 kW, to match the higher throughput capacities being achieved. This due to uprated eccentric speeds and larger discharge annulus. Increased eccentric throws and mantle diameters are also now a reality, when compared to more traditional designed gyratory crushers. To keep up with the improved design features of the Mk V, digitalisation has also been upgraded to maximise performance capabilities to ensure that the most efficient reduction and throughput capacities are achieved, whilst utilising the higher powers now available as standard. Condition monitoring ensures that the crusher is at its optimum operating capability by monitoring and adjusting the crusher settings via feedback from additional sensors, ie main shaft spin, temperature and vibration. Camera monitoring capabilities are available as is an advanced oil contamination monitoring system. As a result of the above design improvements, it will be shown that the Mk V range offers benefits such as: enhanced safety features, increased availability, faster maintenance turnarounds, higher power utilisation, equivalent product size at higher throughput capacities and with Remote operation capabilities. All of which result in a gyratory crusher with higher levels of safety and a lower per tonne operating cost.

Sep 18, 2023

The Graham Farmer Freeway Project in Perth, Western Australia, is the largest urban infrastructure project ever carried out in the State. At a project cost of over $360 million, it also ranks as one of the largest in Australia and is even large by world class standards. The project provides a much needed east-west freeway bypass around the CBD of Perth, linking the Great Eastern Highway in the east with the Kwinana and Mitchell Freeway system in the west. The Bypass will have 6.5 kilometres of freeway, a major bridge over the Swan River, several pedestrian overpasses and underpasses, dual use paths, interchanges and flyover bridges and a rail tunnel. The whole project is being carried out over a four-year time frame, due to be complete and open to traffic in June 2000. The project has been divided into two stages, with Stage 1 including the 1.63 kilometre long Northbridge Tunnel, the subject of this paper.

Jan 1, 1999

By J Bassan

The mining industry is faced with imperatives to improve worker safety and productivity, adapt to skills shortages, high worker turnover rates, and provide more effective maintenance to new and ever more complicated plant and equipment. While more effective use of data combined with advanced analytics offers opportunities for improvement, providing this information to the worker in the field, in real-time, has proven expensive, cumbersome and ineffective. New capabilities are now emerging which address some of the limitations experienced to date. Augmented reality (AR) provides a means to overlay interactive digital information on top of the physical world. Combining the latest visual display, mobile computing and ‘track and trace’ technologies, AR provides an experience similar to a heads-up display in a fighter jet through small, personnel devices, such as smart phones or wearable glasses. Applying AR would allow a mobile worker to ‘see’ all relevant information for a given task, in the context of their physical environment and at the time they require it. The technologies behind AR are rapidly maturing and becoming available at a price point that is viable for commercial applications. It is anticipated that AR will become ubiquitous at a consumer level within the next five years. The specific challenges faced by the mining industry make it an ideal early adopter of AR technologies. This paper examines a number of use-cases of how AR can be applied to the mining industry and the benefits that can be realised. The paper will identify areas of further work and viable opportunities for immediate adoption within the industry.

Nov 22, 2011

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Improved roof control in high deformation tailgate environments has been achieved over the last decade through development of stiffer and increased capacity standing support products. æThe CanÆ is one such development, being a steel cylinder containing a weak cementitious fill, designed to essentially fold in upon itself whilst maintaining strength. A laboratory study to better define the relative load contributions of the steel cylinder and fill, the confining interaction between these components and most importantly, the potential impact of varying the steel and/or fill properties is described. This would enable the support engineer to ædial-upÆ the desired strength and stiffness properties and optimise the standing support design with respect to load capacity, stiffness, weight (handling) and cost. Design curves to optimise strength based on steel casing thickness, fill strength (confined and unconfined) and æCanÆ geometry were established. Scaled-down (one-third) samples were used in the test program and found to adequately reflect the loading behaviour of full-scale versions, thereby providing significantly greater scope for further product development at less expense compared with testing full-scale products.

Jan 1, 2005

By C L Humphrey

Biological monitoring programs for environmental protection require techniques that will provide both early detection of possible adverse effects, and assessment of the ecological significance of these effects. Monitoring techniques must include responses sensitive to the impact, that can be subjected to rigorous statistical analysis and for which statistical power is high. Such issues in baseline research of 'what and how to measure?' and 'for how long?' have been the focus of a program being developed to monitor and assess effects of mining operations on the effectively pristine, freshwater ecosystems of the Alligator Rivers Region (ARR) in tropical northern Australia. Application of the BACIP design, utilising a form of temporal replication, to univariate data (single species) and multivariate (community) data is described. For new ventures in Australia (such as mining), monitoring programs should be designed to establish with high probability that an impact on the ecosystem no greater than a prescribed amount has gone undetected - as opposed to simply allowing development to continue as long as 'proof' of impact is not available. Such a precautionary approach represents a shifting of the 'burden of proof' and would require with the BACIP design, a minimum number of baseline years in order to achieve some desired level of statistical power in a test for impact. Power analyses conducted on two to five years (depending upon the technique) of baseline data from streams of the ARR indicate that the BACIP design would not impose developmental constraints on mining and that a policy of reversal of the burden of proof would provide the cornerstone required for managing such development in an ecologically sustainable manner.

Jan 1, 1994