Search Documents

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

The environmental and social responsibilities of the mining industry have long been recognized by the industry itself, but during the past decade it became one of the main targets for the more radical members of the community. This came as something of a shock to an industry which had always considered that it had acted responsibly within the standards of the day. As far back as early 1968, the Australian Min- ing Industry Council (AMIC) was clipping from newspapers the odd letter written by environmen- talists and critics of mining activities. In those days every such letter was carefully studied to ensure that AMIC, if not having the answers, at least had an understanding of the types of argu- ments then starting to be used against mining activity and in favour of environmental preserva- tion. Within 18 months, the infrequent letter to the editor had become a flood of such letters and feature articles, and the environmentalists' attack on mining activities had been launched in all its Vehemence.

Jan 1, 1978

By P Shen, K Hattori, H Pan, E Seitmuratova

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore-bearing intrusions in the Central Asian Orogenic Belt (CAOB) were examined from nine mines: Boshekul, Nurkazgan, Kounrad, Borly, Aktogai, Koksai, Baogutu, Tuwu and Erdenet. The intrusions are diorite, granodiorite and tonalite with SiO2 contents ranging from 58 to 75 wt per cent, and show mildly fractionated rare earth elements (REE) ([LREE]N/[HREE]N = 2.7–4.7) – light REE and heavy REE – and varying Eu anomalies ([Eu]/[Eu]* = 0.58–1.4). The ratios of Sr/Y vary from 7.9 to 115 and the contents of Y from 4.6 to 23.9 ppm. The parental magmas of the intrusions are intrinsically oxidised. Zircon grains in the ore-bearing rocks from large- and intermediate-sized porphyry Cu deposits show high Ce4+/Ce3+ ratios characterised by 65–422 at Boshekul (>4.1 Mt Cu), 76–480 at Kounrad (>4.8 Mt Cu), 90–280 at Aktogai (>12 Mt Cu), 80–250 at Erdenet (>11 Mt Cu) 74–370 at Nurkazgan (>3.9 Mt Cu), 100–210 at Koksai (>1.6 Mt Cu), and 71–340 at Tuwu (~2.0 Mt Cu). In two small deposits, the ore-bearing rocks display low values of Ce4+/Ce3+; Borly (0.6 Mt Cu) ranging from 28 to 158, and Baogutu (0.6 Mt Cu) from 29 to 113. The Ce4+/Ce3+ ratio of 120 distinguishes large intermediate-size deposits from small-size deposits. This information is potentially useful in exploration for porphyry Cu deposits in the belt.CITATION:Shen, P, Hattori, K, Pan, H, Jackson, S and Seitmuratova, E, 2015. Granitoids associated with porphyry Cu deposits in the Central Asian Orogenic Belt – characteristics and oxygen fugacity, in Proceedings PACRIM 2015 Congress, pp 377–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Lyman G. J

Magnetic separator operation in the recovery of magnetite in heavy medium circuits was studied by conducting a series of tests on a full size wet drum magnetic separator.The significant operational variables were found to be feed pan clearance, squeeze pan clearance, dry magnetite feed rate and separator drum speed. With feed and squeeze pan clearances optimized for typical primary separator operation, magnetite loss and concentrate specific gravity were found to be related in a regular manner to dry magnetite feed rate at any drum speed.A two component model of magnetite loss is proposed, relating total magnetite loss to losses in the feed pan and squeeze pan zones. The experimental curves relating magnetite loss to dry magnetite feed rate at the various drum speeds are interpreted in terms of the two component model.The magnetite particle size distribution in the separator was also examined. The tailings magnetite was found to be finer than the feed magnetite only when the dry magnetite feed rate was low, or immediately following the introduction of a new charge of magnetite when the separator was fed at an intermediate dry magnetite feed rate.

Jan 1, 1983

By Williams C

A stibnite concentrate from Golden Spec (WA) was subjected to a series of tests involving high pressure cyanidation and pressure oxidation followed by conventional cyanidation. The concentrate, whose gold content was 18.1 g/t, yielded only eight per cent of the gold when leached directly by a standard 24-hour cyanidation test. The recovery was increased to only 15 per cent when pressure cyanided under the following conditions: ambient temperature, 2000 kPa oxygen pressure, two hour retention time and 30 per cent w/w solids pulp density. This poor response to pressure cyanidation emphasised the refractoriness of the material. Evidence of the fine distribution of the gold through the concentrate, from measurements of the particle sizing distribution and the gold analyses of the individual fractions, also suggested that this concentrate was highly refractory. Pressure oxidation of the concentrate at elevated temperatures followed by cyanidation yielded recoveries as high as 94 per cent. However a preoxidation treatment under the following conditions was necessary: 230¦C, 2000 kPa oxygen pressure for a period of four hours.

Jan 1, 1992

The need for formalised geotechnical reporting has not been fully explored at many operations. With the continuing need to provide safer and more efficient workplaces, the requirement for good geotechnical reporting systems (as with other reporting systems) has become of greater importance.Historically, the risk from rockfalls has been the largest cause of fatal injuries in the underground mining industry. The response of the ground to mining is generally poorly documented at many mines. At Olympic Dam, it was found that the existing corporate hazard and incident reporting (HIR) procedure did not record enough specifics about geotechnical issues. A separate and more specific geotechnical reporting process was set up to address this problem.This paper examines the role that geotechnical reporting plays at the WMC Resources Olympic Dam Mine; from reporting and rectifying day-to-day geotechnical issues that affect the operation to documenting and analysing longer term trends.

Jan 1, 2004

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

Bioleaching Metals from Waste Printed Circuit Boards and the Shapes of Microorganisms

Sep 13, 2010

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

In 1976, The Zinc Corporation Limited Broken Hill set up a plant to re-process a hill of tailing (Mt. Keast) from the original treatment operations. With the likely disappearance of this source of feed in 1985, an investigation was initiated to determine what other feed sources might be available. This involved searching through old records and photographs as well as a subsequent drilling campaign. The paper briefly covers the history of treatment operations and describes, as a result of the information obtained, the likely future sources of feed.

Jan 1, 1983

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

Having successfully applied computer techniques to open pit mining applications, many software developers are now using their skills to tackle the much harder areas of underground mine design, planning and production.Dramatic improvements in the performance to price ratio of hardware (including high resolution graphics screens), a better understanding of the techniques of surface and solids modelling (and their subsequent display), moves towards standard user interfaces and advanced concepts of representing grade distribution in the ore body have all contributed to the recent increase in underground mining software activity.This paper details the general requirements of a workable underground mining software system, providing a minimum checklist of desirable features and emphasises the importance of ease of use, flexibility and intuitive feel. Some relevant trends in hardware, software and application techniques are highlighted and comments made on areas which require further development or are only available in a small number of packages.Finally, a comment is made on the role of computer models to provide a unifying medium for tying together all aspects of underground design, planning and production.

Jan 1, 1992

The results of precious metal exploration carried out by Amoco Minerals New Zealand Limited over EL 33-137 in the Longwood Range, Southland, are described. Widespread gold and platinum in alluvial deposits on the perimeter of the range and anomalous gold in stream sediments on its southern and south western flanks indicates that the precious metals were probably derived from erosion of the mafic rocks of the Longwood Complex.

Jan 1, 1983

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By Otuonye F

An outburst is the spontaneous ejection of pulverized coal and gas from the working face in an underground mine. It is caused by overstressing the rock, due predominantly to the influence of geological structures on in situ stresses, stress concentration from the excavation and overburden load on mine openings, and large volumes of gas sorbed in the rock. The spontaneous release of high pressure gas creates intense shock waves which may cause damage to the mine ven- tilation system and the pulverized rock/coal ejected may cause injury or death to miners. The gases emitted pollute the mine air and may also result in death to miners.

Jan 1, 1988

Qualitative measurement of respirable dust in metal mines is limited and an example of this is demonstrated at Northparkes Mine, where operational experience was sought for measuring dust standards and identifying exposure limits. However, relying on operational experience has limited value due to variation in observations from person to person and is based on visible dust (which is larger in size than respirable dust). However, with sophisticated dust measuring equipment, like the real-time aerosol monitor, dust concentrations can be accurately measured and recorded concisely. Research conducted as part of a collaborative agreement on behalf of Northparkes to launch an occupational dust monitoring program was implemented on the mine site. To form the basis of this research, it was hypothesised that no proper dust measuring testing at the mine site had been adequately identified. In addition, existing occupational hygiene monitoring programs did not adequately quantify employee exposures to these hazards. This project will outline the results of an occupational dust monitoring program, hence greatly improving the capacity to quantify the health risks posed to employees.

Jan 1, 2008

The Karangahake gold-silver deposit is located 11 km west of Waihi in the southern part of the Hauraki Goldfield. Historically it was the second largest bullion producer in the goldfield with a past production (1882 - 1944) of 126.712 tonnes of gold-silver bullion (Au:Ag ratio of 1:3.3) from 1 142 315 tonnes of ore grading 27.4 g/tonne gold equivalents.

Jan 1, 1987

By Mitchell M. A

The steeply dipping Mammoth orebody is mined by Gunpowder Copper Limited using a sub- level uphole bench stoping method at a mining rate of 350 000 tonnes per year. of three per cent copper ore. Access to the mine, is provided by 1 in 9 decline which spirals in the footwall connect-, ing all the sublevels, thus maximising mobility and accessibility of trackless mining equipment Sublevels are driven in ore off cross- cuts from the decline every 15 metres vertic- ally. Sublevel drives are stripped out to widths up to 18 metres before cutoff slots are mined at each end. A two boom fan drilling jumbo is used to drill inclined rows of holes to the floor of the sublevel above. Two or three rows are fired at a time which allows broken ore and remnants from the level above to be mucked out by rubber tyred LHD equipment to the brow. Ore widths of up to 80 metres are en- countered at lower levels where ring drilling from longitudinal drill drives will break ore to a draw point system below. Development is carried out with three boom rubber tyred jumbos. All haulage from the mine is in 20 and 35 tonne rear dump trucks. All aspects of the mining operation are discussed including ventilation, pumping and drainage, services and future planning.

Jan 1, 1974

By R-H Yoon

A turbulent flotation model has been developed by considering the subprocesses of collision, attachment, detachment, and froth recovery. AbrahamsonÆs model (1975) of infinite Stokes number is used to model collision, while the attachment and detachment subprocesses are modelled by considering the kinetic energies required to overcome the energy barriers and the work of adhesion, respectively. The energy barriers are determined by considering various surface forces, including electrostatic, dispersion and hydrophobic forces, while the kinetic energies are determined from the particle velocities at close separation distances from air bubbles. The latter has been determined by modifying the turbulent root-mean-square (RMS) velocities of Liepe and Moeckel (1976) and Schubert (1999) in view of a lubrication theory. In calculating the RMS velocities, it is assumed that a flotation cell is subdivided into low and high energy dissipation zones. The model predictions made by varying various hydrodynamic and surface chemistry parameters are consistent with flotation practice.

Jan 1, 2005