Search Documents

By M Zlatev, S Silge

Producers of primary resources such as iron ore face the challenge of processing crude materials with increasing levels of impurities, which may result in the requirement for wet processing. This results in a significant increase in water usage, power consumption and operating costs. Given the remote locations of most operations in Australia (Stewart et al, 2013; Prosser, Wolf and Littleboy, 2011), the required volumes of power and fresh water for wet processing can be very difficult to achieve.HAVER&TYLER is renowned across the world for their screening technology in wet and dry processes. Its innovative Hydro-Clean® system represents a cost-effective and eco-sensitive way to clean any crude materials and material blends with a grain size distribution of 0–150 mm that are contaminated with adhesive clay, slit and other impurities.CITATION:Silge, S and Zlatev, M, 2015. Iron ore washing – achieve more with fewer resources, in Proceedings Iron Ore 2015, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By H M. A Ilyas, M Yahyaei, S Amari, M Darestani

Tailings are generally deposited on or near to the mine sites, occupying the site area, and being an economic burden for mining companies. Tailings can cause several environmental impacts, such as leaking toxic substances and contaminating underground water, emitting greenhouse gases, and damaging natural bodies and wildlife. Geopolymerisation of mine waste effectively transforms mine waste into more valuable, environmentally friendly products. Geopolymers are inorganic aluminosilicate materials that are widely applied in the construction industry (Araya, Kraslawski and Cisternas, 2020). The high performance and the low-CO2 emission of geopolymers make this type of material potentially more desirable than ordinary cement, given that manufacturing one ton of traditional cement generates approximately 0.8 tons of CO2. This process is seen as a promising method for repurposing tailings and reducing the environmental impact of mining waste. However, the environmental impact of geopolymer production is not sufficiently comprehended (Mazzinghy et al, 2022). Moreover, geopolymerisation of mine waste can offer several economic benefits, including reduced waste management costs (Amari et al, 2019; He et al, 2022), reduced raw material costs, and potentially lower production costs. However, there are several challenges that need to be addressed to ensure the economic feasibility of the process. This study aims to demonstrate the potential environmental impacts of geopolymer concrete produced using mine wastes and industrial by-products such as blast furnace slag (BFS). For this, a comparative cradle-to-gate life cycle assessment (LCA) methodology was conducted on different geopolymer mix designs, and the greenhouse gas (GHG) emissions results were compared to the ordinary cement. LCA can be used to evaluate the environmental impact of geopolymerisation of mine wastes in various ways. One important impact category is GHG gas emissions, which contribute to climate change and is the focus of this study. Another aim of this study is to evaluate the economic feasibility of the geopolymerisation of mine wastes via economic analysis (EA) to identify the key economic factors and trade-offs associated with repurposing mine wastes through geopolymerisation.

Aug 2, 2023

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995

By Fourney W. L, Dick R. D

A small-charge rapid excavation system employing a novel penetrating cone fracture initiation and propagation technique has been demonstrated to be capable of excavating the hardest of rocks at efficiencies (energy per unit volume of rock removed) four to ten times greater than attainable with conventional drill and blast. Significant enhancements to the concept developed during the research efforts include the use of propellant rather than explosive charges and a device for containing the charges and effectively sealing the shot-holes. The experimental results, including the excavation of several tons of hard rock in a research mine, have confirmed the novel breakage process and provided a data base for the design of a continuous hard rock mining machine based upon the concept. The small-charge excavation system would be attractive for civil construc-tion operations where sensitive structures, equipment and personnel would be in close proximity to the excavation face. The system would be attractive for selective mining operations where the ore rock could be fragment-ed and processed separately from the barren country rock. The barren rock could then be backfilled underground and eliminated from the traditional hauling and milling operations.

Jan 1, 1990

By Canning RG, Uusna S, Goodheart BA

The paper outlines the development of"a process for removal of iron oxides from ilmenite, thereby upgrading the TiO2 content of Western Australian ilmenites, from 55 to approximately 90 per cent. In the first stage, the iron oxides are reduced with solid carbon (coal) to metallic iron. Experimental reduc- tions were carried out in crucibles,, a fluidised bed and a small pilot plant rotary kiln. The reduced'ilmenite is,then agitated in aerated water, in the presence of catalysts, so that the iron "rusts" away from the ilmenite'grains and the precipitated iron oxide is easily separable by decantation. The influence of variables on the rates. of reduction and oxidation are discussed, The oxidation rate was exam- ined for both - the' physical oxygen-transfer characteristics and electrochemically by reference to Peurbaix diagrams, which plot redox potential against solution 'PH, The upgraded ilmenite is expected to be an attractive material. for pigment -manufacture,, and the iron oxide has prospects of being a marketable by-product. The process may possibly be. applied, to .other..ores.

Jan 1, 1964

By Bockhorst R. W, Christopher D. A

Over the past fifteen years, horizontal drilling in coal seams for advance degasification has become an established practice in the United States of America. Consolidation Coal Company pioneered the development of the horizontal drilling system and licensed the technology in the U.S. A. and to Du Pont (Australia) for commercial production. This paper discusses the most recent developments in the equipment design, especially the borehole telemetry system, known as the Downhole Drill Monitor (DDM).

Jan 1, 1988

By K Ellis, K Quast, R Newell

The use of ammonia as a leaching agent in the recovery of copper from ores and concentrates has a number of potential benefits. These include the ability to treat ores with an acid consuming gangue, non-corrosivity, the insolubility of iron in the solution and increased selectivity. This paper reviews the previous and current use of ammonia based leaching systems for copper recovery and presents the results of a laboratory investigation that involved leaching of a copper concentrate and a low-grade ore. The effects of the operating variables (particle size, oxygen addition, agitation and temperature) are discussed. Of these, the particle size had the greatest effect, with decreasing size giving improved leaching rates and recoveries. The possibility of using ammonium salts in heap leaching is also discussed, and the results of some small-scale column leach tests presented. Possible methods for recovering the copper from the leach solution are outlined, and the types of ores and concentrates for which ammonia leaching may prove to be a viable alternative processing route are discussed.

Jan 1, 2000

Projected cooling requirements for ERPM led to the first proposals for the large- scale use of ice for mine cooling in the early 1980's. Following successful research into ice conveying and ice melting a large ice plant was commissioned at Harmony in 1985 and a much larger 6000 ton per day plant is presently under construction at ERPM. A brief description of the mining project is given, followed by general descriptions of the surface ice plants and the ice conveying system, the systems for using the ice for mine cooling, and the control of the whole ice cooling System.

Jan 1, 1988

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Performance driver trees or KPI trees are reasonably well-known tools for analysing performance in mining operations. However, the tools are often not user friendly. They may be technically correct but they are often clunky. This means they donÆt promote simple management decision-making and donÆt encourage businesses to make them an integrated part of optimising their operations. This paper describes a simple but effective driver tree process and tool that has been successfully implemented and used to aid decision making across a number of mining and processing operations. The important aspects of employing driver trees to assist in management of operations are to ensure that the chosen solution:includes a reporting solution, provides the bottom line impact of the performance indicators, automatically gathers the necessary data that reconciles with existing reports, and is built around a review process that fits with existing management processes. An adequate solution enables operators to identify where there are performance gaps and to quickly prioritise the urgency for addressing these issues. Two case studies are chosen to illustrate the critical success factors of implementing a performance driver tree solution. The first is a large, complex open pit operation. The driver trees, reporting and management processes were initially established for the mining and processing aspects of the operations. Once the initial solution was bedded down, a follow-up project was carried out to establish the equivalent solution for the support areas of the business. The final solution covered stand alone performance driver trees for mining, processing, engineering, maintenance, health and safety, human resources and finance. These individual driver trees were integrated into a total solution that showed how all of the identified KPIÆs impact profit and quantified the dollar impact of all variations. The reporting solution that was put in place automatically creates prioritised lists of variances for the business to address. The second case study is a performance diagnostic project where driver trees were used to assess where gaps in performance were occurring, and then to evaluate the impacts of proposed initiatives.

Jan 1, 2007

Bakelite is fairly widely known as a suitable material for the mounting of ore specimens, concentrates and tailings for microscopical study, but has not as yet had extensive application. It is the most suitable mount for specimens which are to be held in the mechanical holder of a polishing machine, based on that described by J. W. Vanderbilt*, which is installed in the Geological Department of the Melbourne University.Bakelite products are prepared by subjecting bakelite powder to a temperature of about 1600 C. under a pressure of approximately two tons per square inch for a period of four minutes. The shape and size of the products are governed by the use of suitably constructed dies. When the concentrate or tailing is mixed with the bakelite powder, a briquette is produced which can be polished so that the opaque minerals in the sample can be examined microscopically in the same way as in a piece of solid ore. A simple machine for the construction of these briquettes has been described by Head and Slavin. It consists of a small four-pillar press in which the pressure is supplied by...

Jan 1, 1933

By Cocker A

Pre-splitting for smooth highwall formation is conducted in around 75 per cent of surface coal operations within Australia. The CMTE (Centre for Mining Technology and Equipment) in conjunction with BHPAC (BHP Australia Coal) initiated a project to look at pre-splitting and to investigate the notching of blastholes for fracture plane control. The notching was specifically for pre-split initiation and also for discing of the toe of the production holes to minimise coal loss from the top of the coal seam. There are currently a number of factors which are driving the introduction of new pre-splitting technologies and products. The first is the ever increasing bench height being employed in strip mines which require a higher quality wall with less blast damage to maintain stability. Currently depths of 55 metres are common place with depths of 70 - 80 metres fast approaching. The second factor is the introduction of new technologies or methods which require a high quality highwall produced, eg highwall mining. This paper discusses the current state-of-the-art in pre-splitting and the main issues facing successful pre-splitting in the future. The use of a blasthole notching technology to promote fracturing along the pre-split line is also analysed. The review indicates that most pre-splitting challenges in the future can be addressed through better use and developments of current drill and blast technology. It is also concluded that a blasthole notching technique may find niche applications in improving final walls within a surface coal mine, especially where a high quality wall is required. The notched blasthole method may also allow pre-splitting in ground conditions and adverse rock structure which currently cannot be pre-split by existing technology.

Jan 1, 1995

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By D S. Nicholson, T Marshall

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while opencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

We have been exploring for minerals in Australia for over 100 years and our methods are constantly improving - but why do we pros- pect? Is the effort justified? Obviously the main motive is economic gain. It is now and always has been but conditions are changing rapidly. Once it was the prospector who could cash the nugget. Then it was the syndicate, the small company, an amalgamation of small companies, the large company, the corporation; the multinational corporation - where do we go from there? Early there was personal satisfaction and excitement in out-door activity which gave scope for individual energy, hope and in some cases reward. There still remains the satisfaction, either individual or corporate that a mineral discovery creates new wealth and makes a contribution to the nation's well being. Parallel with developments has always been the growth of restraints on exploration, frequently out of phase with the current mineral developments - miners' rights, licences, titles, royalties, mining laws and regulations, taxation etc. As the operations have become more complex so the restraints have become more confining until it is now very necessary to question whether the chances of economic gain justify the risk and responsibility of mounting costly mineral exploration leading-to extensive capital development.

Jan 1, 1974

By A G. L Pratt, G F. Dunstan, A Leonforte

The selection of the material sizing and mine dewatering systems are important elements in the development of a large-scale, high tonnage (greater than 4 Mt/a) underground hard rock mine. The sizing system will influence the size and type of the ore haulage system and therefore how the underground project is developed. With more underground developments considering or implementing caving methods of mining, the selection of the material sizing systems is also influenced by the caving fragmentation. Traditionally, crusher systems are used for material sizing in large hard rock mines, with the crusher installation and its ancillary equipment representing a substantial capital investment. Underground cave mining type operations generally express themselves with large surface subsidence areas, which can lead to large inflows of water from major rain events or purging underground aquifer systems. To minimise disruption to mine production, the dewatering system needs to be sized, with consideration to both storage and pumping capacities. The balance between storage and pumping capacity is assessed to provide the optimal economic solution with the appropriate risk measures. This paper outlines a process for the selection of material sizing and dewatering systems for large-scale caving operations. This process is illustrated with information drawn from NewcrestÆs Ridgeway Deeps Block Cave project. The Ridgeway Deeps Block Cave is located directly beneath the existing Ridgeway Sublevel Cave Mine.

Jan 1, 2008

For more than 15 years after the Northparkes orebodies were first discovered in 1976, the project was delayed by the need to find an economic way of mining the low-grade E26 deposit. The decision to use a low-cost block caving method to mine the orebody was made in the early-1990s; but the project's future did not solidify until 1993 when a radical new approach was adopted which sought to integrate business imperatives with technology and organisation strategies. The approach led to the establishment of a strategic vision which tied together all the components that could have a major impact on the project, to provide a framework for guiding strategic choices. The strategic vision strived to break away from the old rules of how mines are organised and operated; and involved finding imaginative new ways to radically redesign mining processes to achieve quantum leaps in performance.

Jan 1, 1997

The mining industry is the largest source of foreign income for South Africa. It is also the main source of employment in the country and, as an industry; it is also one of the largest. Due to the labour-intensive nature of the industry, labour costs in South African mines make up nearly 50 per cent of the total mine cost. It is thus imperative to have optimum labour planning and labour management systems in place.The focus of this study was to investigate current underground labour-planning models. It is shown that there are serious limitations. The range between an oversupply and undersupply of labour can be as high as ten per cent. A new system was therefore developed to ensure a constant labour demand and supply on a daily basis. One of the main objectives was to determine the existing labour supply range and thus the requirements to fill the undersupply. For this purpose, a specific methodology was designed to capture and process all the relevant information. Mine personnel was involved throughout the entire process to ensure ownership of the new model. This buy-in was achieved through planning workshops, interactive presentations and discussions. The improved frequency of daily blasts validated the new system by providing the correct amount and mix of the labour force. The new labour-planning model was then extended to optimise revenue. Implementation on a mine resulted in increased income of R95 million.

Dec 6, 2010