Search Documents

Some of the major factors affecting ore reserve estimation in gold mines are discussed together with their impact on computational methods.The major priority in ore reserve estimation is to get sampling and geological problems resolved. Poor basic information cannot be remedied by mathematical methods.Generally the more complex a deposit becomes the greater the need for subjective assessment and the less applicable are more complex ore reserve methodologies.

Jan 1, 1984

By C Gourdon

The present study concerns a new type of mixer-settler unit where coalescence is promoted by means of the phase inversion method (MSPI). Using two different systems (alkaline etching solution û LIX 54 in kerosene and acidic aqueous solution û LIX 984 in kerosene) the influence of the total flowrate, the A/O phase ratio and the hydrodynamic conditions in the nozzles of the scattering device on the extraction and separation efficiencies are studied. Two modes of operation are clearly outlined and a theoretical model predicting the separation efficiency is proposed and compared to experimental results. A comparison between mixer-settlers with classic decanters and the MSPI unit has demonstrated the advantages of the latter where throughputs in the range 20 -25 m3.m-2h-1 can be easily realised.

Jan 1, 2000

By G Yeowart, P D. Munro

The Prominent Hill copper-gold concentrator of OZ Minerals Limited in South Australia was built in 2008 and commenced commercial production in early 2009. It has a design ore throughput of eight million tonnes per year (Mt/yr). While the flow sheet has many items in common with other plants treating ores from iron oxide-hosted copper-gold deposits, the Prominent Hill concentrator also has some unique features. Plant design has been based on a 'template' of the very successful Ernest Henry concentrator. Initial options considered for processing Prominent Hill copper-gold ore are briefly examined as well as potential complications arising from the presence of a considerable tonnage of 'gold-only' material present in the deposit. Metallurgical test work and the subsequent decisions leading to the selection of a conventional crushing, semi-autogenous grinding (SAG) and rougher flotation circuit is discussed. One particular difference with other plants treating this ore type is that metallurgical tests and mineralogical studies identified that rougher concentrate had to be reground to a P80 of 20 - 25 microns or finer for adequate liberation of fluorine-bearing minerals. Subsequent satisfactory separation of fluorine-rich gangue material from the valuable copper sulfides requires highly efficient cleaner flotation to make a commercial quality copper-gold concentrate. Xstrata Technology's IsaMillÖ and Jameson Cell technologies developed to meet similar taxing fine grinding and flotation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province were selected for regrinding and cleaner flotation. Plant design has features aiding ergonomics for ease of operation and maintenance not commonly seen in recent projects with large sulfide flotation concentrators.

Jan 1, 2009

By Sen G

An amount of explosives, whether it be cylindrical, spherical, etc in configuration, with a hollow cavity in one face or end is known as a hollow or shaped charge. When this charge is initiated, a focussing of explosive energy will occur within this cavity. This focussing, or concentration of detonation products creates an intense localised force greater than just the simple detonation of a conventional explosive, (without a hollow cavity). If this hollow cavity explosive is directed against a target material this concentrated force is capable of creating a deeper penetration than the same amount of explosive without the hollow cavity. If a metallic liner material is used in the hollow cavity, upon detonation of the explosive this liner will form into a high velocity penetrating jet. Depending on the explosive type and the liner material's configuration the jet tip can travel up to 10 km/s. Linear shaped charges were developed using the abovementioned shaped charge concept but instead of being formed about an axis, they are elongated and constructed along the principal axis. Therefore instead of creating a narrow circular penetration jet, it forms a thicker planar cutting jet ideal for linear cutting purposes. Using Linear Shaped Charges (LSC) for pre-splitting is expected to result in more accurate directional fracture propagation, while minimising lateral micro fractures in the surrounding rock mass which is required to remain undamaged.

Jan 1, 1995

Part of a four-year course in metallurgy, dealing with metallurgical process engineering, was designed for students to acquire knowledge and skill from physical science, metallurgy, process engineering, and social science. Principles of education, and guidelines obtained from a study of professional practice, indicated that students may learn effectively through a planned sequence of problem-solving exercises based on the diverse functions of metallurgists in industry. The more important characteristics of the curriculum and a few illustrations of the problems are included. An outline is given of the current procedures used to develop parts of the curriculum, and of the students' diffic- ulties and achievements.

Jan 1, 1984

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Alternative processes for converting coal to liquid products and their stage of development are outlined. The merits of hydrogenationprocesses in general, and the solvent refined coal process in particular, are stressed. Bench scale experimental hydrogenation procedures used by the Australian Coal Industry Research Laboratories Ltd. (ACIRL) to study the liquefaction of Australian coals and correlations between properties of such coals and their conversion to liquid products are described. Factors involved in assessing investment and operating costs for modern hydrogenation based coal refineries of different capacities are described with reference to a recent study undertaken in N.S.W. The significance of coal properties such as yield and yield structure of total liquid products and how they and other factors can influence the economics of the coal refining operations are discussed.

Jan 1, 1977

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation is to improve the accuracy and consistency of mining processes and less to do with cost savings through labour reduction. A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio Tinto's surface mines. This paper describes Rio Tinto's drill enhancement project that has developed a robust system for automating most of the functions on a Terex SKSS16 drill rig. Automated drilling is currently being used in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the drill automation system is given together with an overview of how automated drilling is performed remotely from the mine office. A review of some of the benefits of the enhanced drill system is given together with the future plans to extend the functionality of the automated drill and the expected benefits.

May 1, 2010

By Musa MA

Tunnel excavation for sewer construction long remained a labour intensive, hazardous and costly operation. Even with the of mechanical and semi-mechanical shields for tunnel excavation, many problems remained until recently. In the past decade, however, the technology has changed dramatically which has made possible the use of advanced tunnelling methods for sewer construction.

Jan 1, 1993

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

Optical sensors have emerged during the telecom boom in the late 1900s, due to the availability to low-cost telecom-grade optical components. It's only after the telecom industry's fall in 2004 that optical sensors became sufficiently developed to be a viable technology for real-world applications. Geotechnical applications have long relied on electrical sensors such as thermocouples, strain, and the venerable vibrating wire to measure physical phenomena. Although these are well suited for a large variety of applications, electrical sensors cannot be used for all applications: these are vulnerable to noise, hazardous voltages and corrosion, limiting the environments in which they can be used. In addition, electrical wires can also become an issue when sensors require external excitation or are distant from the measurement system. Finally, changes in physical properties of electrical sensors and systems over time makes regular calibration a necessity - not easy to do when these are permanently mounted on structures. Optical sensing systems are non-conducting and use light to perform various measurements. There are several optical sensor technologies available, each with different strengths and weaknesses. In addition, there are different methods of interrogating optical sensors, each of which also present different strengths and weaknesses. To make matters worse, configuring the interrogation and scaling to physical units can also be challenging to the unprepared engineer. This paper will present a holistic view of optical sensing, presenting the different optical sensor technologies and interrogation techniques. Sample optical sensing systems will be revealed and top considerations for optical sensing will be presented.

Nov 25, 2010

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

The Bowen Basin coal field is an important energy resource. A relatively small proportion is avail- able by open cut operations. Responsible men throughout the world have warned of the need to increase coal research immediately. Because energy is still available in abundance these warnings have not been heeded in Australia. The characteristics of the Bowen Basin coal make it a fairly difficult underground mining proposition and a significant research effort is required to solve the problems likely to be encountered. Both industry and government have responsibilities in the economic recovery of the maximum proportion of the resource and jointly funded research administered by existing organisations should be inaugurated forthwith.

Jan 1, 1976

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By Dr Subagyo

The energy consumption for producing metal from ore is strongly linked to the chemical stability of mineral being processed, availability and richness of the ore, and process route. Energy efficiencies are particularly linked to the process route. The energy efficiency of high temperature operations vary considerably but energy efficiencies greater than 70 per cent are achieved for large-scale metal production. Low temperature processing through grinding, leaching and subsequent electrowinning use large amounts of energy. In particular, grinding and electrowinning suffer from low overall energy efficiencies. The physical chemistry of a new proposed low temperature route, reactive ball milling, is unclear but preliminary evaluations indicate that it is likely to suffer from high energy consumption. In conclusion, low temperature processing routes for metals generally consume more energy that comparable high temperature processing routes.

Jan 1, 2002

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

The Joint' Venture Method is a procedure for assessing the value of exploration properties, particularly those for which resources have yet to be delineated. It aims to convert the terms of an actual or synthetic joint venture into the equivalence of an arms- lengths cash transaction between a willing seller and a willing buyer. This paper sets out one approach to achieving that conversion. It discusses both simple and complex cases and gives some examples from both public and private documents. It also includes some case studies in which the Joint Venture Method of valuation can be compared with values derived for the same project using other methodologies including actual cash deals. The Method has failings in both mathematics and logic. However because it does reflect or simulate an arms-length deal which takes into account past exploration effort and expenditure and an assessment of prospectivity at a particular point in time, it is felt that it can provide a reasonable approximation of trade value or asset value of a prospect, particularly if used in conjunction with other methods.

Jan 1, 1994

By M B. McKevitt, W J. Shaw

The main task of grade control on a daily basis is to define the material that should be mined to a destination under various categories. This can be determined by grade, lithology, quality and blending criteria. In the case of multi-element deposits or deposits with various blending or other processing criteria the optimum selection of ore block boundaries can be quite complex. In every case the balance between ore loss and dilution must be considered when designing the ore block boundaries and this becomes a risk-based decision when using the conditional simulation model. The use of such systems allows grade control to meet specific targets, such as budget tonnages and grades and blended product specifications. Two case studies are presented: the Prominent Hill copper/gold mine and the Rapu Rapu zinc/copper mine. Mining is based on a rational grade control strategy involving a number of factors, including strong geological control, advanced geostatistical approaches, such as conditional simulation, and optimisation of the ore blocking to meet production requirements. This provides an objective, transparent and repeatable grade control strategy.

Jan 1, 2009

By Reichman J, Chapman G

The features of seam gas drainage from the point of view of mathematical modelling are outlined and discussed: 1. The use of conventional single phase gas reservoir simulator for very simplified modelling. 2 Alteration of a conventional petroleum reservoir simulator into a specialised simulator for seam gas drainage. 3. Application. of a conventional petroleum reservoir simulator for modelling of seam gas drainage by the way of pseudo-functions and sacrifying one dimension.

Jan 1, 1982