Search Documents

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

By Reeves M

A review of the literature available in English on kriging and geostatistics is given with the references cross-classified by their subject matter for convenience and ease of use.

Jan 1, 1979

Shear-flocculation is one of a munber of potential processes for upgrading deposits of finely-grained minerals and, more generally, for separating different types of particles suspended in a fluid.The smaller the particle the more likely it is to follow the fluid streamlines, or be entrained within turbulent eddies, and the less likely it is to deviate from the streamline and attach to bubbles (froth flotation), other particles (selective flocculation) or magnetic poles (wet magnetic separation). As shown in Figure I, a number of ingenious ideas have been proposed to overcome this effect. The suspended particles are assumed to be 1 - 10 µm.Thus, the efficiency of attaching ultrafme particles of the valuable component (solid circles) to air bubbles, as in process A, is poor. The efficiency may be improved by attaching the particles to oil droplets (Ralston, Kart and Newcombe, 1984) to form agglomerates that rise or sink (B), to magnetic particles (C) (Parsonage, 1988) to allow recovery in a magnetic separator (D), to other particles to form aggregates (E) that are then either attached to bubbles (F) or recovered by sedimentation (G) (Warren, 1992), and to pieces of polyethylene (Rubio and Baltar, 1991) that rise or sink (H).In A, C, E, F and H, the forces that are generally used to ensure collisions result in adhesion are hydrophobic forces, hydrodynamic forces and inertial forces (Warren, 1992). These drag particles from the streamlines to allow particle-particle adhesion. In B and E, soluble polymeric molecules have been added to bridge between particles as they approach closely during a collision.The second major consideration is selectivity. Selective adsorption of the hydrophobe or polymer onto the valuable particles is the key. Many subtle effects of surface chemistry are involved in obtaining adequate selectivity. A complication in real systems is that the initial suspension is often naturally coagulated and needs to be dispersed before being selectively flocculated.

Jan 1, 1993

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

By Kister H

Hoesch HUttenwerke AG, Dortmund, West Germany, is an integrated steel work of the Estel-group. The nominal annual production capacity-is about 7 Mio tons of steel. Hoesch has along experience in operation of diffe-rent types of slag granulation plants and of utilization of the granulated product. This experience is used to granulate a large amount of blast furnace slag and to process it in own cement plants and produce blast fur-nace cement.

Jan 1, 1979

By N Stoitis, L Lien, B Tapley

The treatment of hypersaline waters originating from numerous gold projects within the Western Australian Goldfields region via membrane technology has been assessed. A combination of Ultra-filtration (UF) and Nano-filtration (NF) using Ecotechnol’s modified elements effectively removes the polyvalent ions responsible for the high lime and cyanide consumption as well as the prevalence of scale formation characteristic of gold operations in this region. Through removing up to 98% magnesium, 94% calcium and 99.7% sulfates from hypersaline water with total dissolved solids from 40,000mg/L to 250,000mg/L, Ecotechnol and subsequent independent tests have demonstrated up to an 87% reduction in lime consumption and through the ability to increase the operating leach pH, reduce cyanide consumption by up to 28%.CITATION:Tapley, B, Stoitis, N and Lien, L, 2015. Modified nano-filtration membrane treatment of hyper-saline goldfields water – an overview and benefits to gold plant operation and economics, in Proceedings MetPlant 2015, pp 431–463 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By Mackenzie JMW, Virnig MJ, Kotze MH

A new range of solid and liquid ion exchange extractants for gold based on the guanidine functionality is described. These extractants have pH versus gold extraction isotherms which lie between those of the conventional weak base and strong base resins which have previously been studied as aurocyanide extractants. Possible applications of these new extractants in gold recovery are discussed.

Jan 1, 1993

THE following notes, compiled in the first instance for the makers of rock-drIlls, were read by Mr. Hanton at a meeting of the Broken Hill Branch on 12th Septelnber, 1922. It was decided that all Broken Hill mines be asked to give their individual views on the subject, so that a comprehensive Broken Hill view could be published. Replies have been received from four (4), mines to date, and their'ideas fairly well coincide with those set out by Mr. Hapton. His notes were as follow:- "The Zinc Corporation Limited.NOTES ON ROCK-DRILL DEVELOPMENTSAs far as our present experience goes, the rock-drill developments on this mine will probably be something resembling the following. The programme is subject to modification or alteratian, according to circumstances. The results of further trials and improvements in present drills, and the design of new types, will, of course, affect any general scheme such as that outlined. It appears reasonably certain that the 3i-in. reciprocating drills which have done practically all the stoping up to date, will be gradually replaced by hammer drills of the internal water-feed type, and that the existing types of hammer drill on the mine will be converted into internal water-feed machines instead of being used as dry machine with outside jet.The ultimate types of machines will be four... Type 1 would be a machine equivalent to the Ingersoll Leyner: 248, Waugh Turbro, SullivaIi DX61, or Holman CH2. This would be used for driving, cross-cutting, and similar excavating work, and possiblyfor stoping also, and should be capable of efficiently working any class of ground. Features, apart from the general requirements set out later, would be the weight of the machine and mounting height of the machine above the seating (as this affects the convenience of boring back or bottom holes); absence of projections on the mounting which the air hose will foul as the machine is fed...

Jan 1, 1923

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

By A R. Proudman, A H. Purvis

The Granites Gold Mine Callie gold deposit is located 550 km northwest of Alice Springs in the Tanami Desert. Gold mineralisation occurs due to a complex interplay of geological factors which include but are not limited to favourable lithology, structure, alteration and quartz veining. High-grade mineralisation, while pervasive under favourable conditions, is highly variable over short distances and is very nuggetty. In contrast, the lithology and geological structures that host the mineralisation are very continuous. Orebody modelling techniques have evolved over time because of a growing understanding of the mineralisation controls. Modelling issues such as sampling and assaying accuracy, modelling method, data density, gold population statistics, geological interpretation and domaining, grade boundary and calculation conditions, and model block size are constantly being reassessed in an effort to increase understanding of the mineralisation controls and modelling accuracy. The evolution of the modelling process in response to increasing data levels and a growing understanding of the mineralisation controls has resulted in changes to the perception of the orebody size and style. This has caused the choice of underground mining method to be revised several times and the process to final mining method selection to take longer than usual. In order to achieve the planned production start-up date of July 1998 the process has been allowed to progress in parallel with development of the underground mine. This paper describes the resource modelling and mining method selection process applied to the Callie underground mine and some of the issues which have contributed to its evolution. Some conclusions that are relevant to the efficient planning and development of new mining projects in general are presented.

Jan 1, 1998

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

It is possible to closely simulate the product sizing distribution from an industrial rod mill by the correct choice of parameters in laboratory batch milling. For laboratory batch rod milling, changes in per cent critical speed and per cent rod volume cause the product sizing distributions to move in parallel at a constant slope. For ball milling, larger sized media in batch milling grind more coarse material giving a closer simulation to the industrial rod mill product. Changing the feed size distribution by removal of coarse particles or addition of fine particles changes the product sizing distribution, but would not normally be practiced in laboratory testing. These data should be applicable to many instances where laboratory simulation of an industrial product size distribution is required.

Jan 1, 1998

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987