Search Documents

The clay slime generatea in many sand washing operations is usually very difficult to de-water. Treatment of these slimes is often limited by economic considerations and the properties of the solids to a gravity-driven process. The moisture characteristics of kaolinitic slimes from two different sand washing operations were measured.From these curves, equilibrium moisture contents for sedimentation and for drainage were calculated using the methods of soil physics. The validity of these calculations were confirmed by column experiments.The results show that the increased de-watering to be gained by drainage, as compared with sedimentation, is significant. Furthermore, observed rates of outflow indicate that water can be removed considerably morerapidly when drainage is possible.The practical application of these results to the dewatering of clay slimes is discussed.

Jan 1, 1978

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008

Over the last thirty years production of heavy minerals from Australian deposits has dominated the world market. The main incentive has been to suoply the raw material for titanium dioxide based pigments. These ~ninerals include ilmenite, rutile, leticoxene and more recently, synthetic rutile. Inevitably the viabilit/ of developing placer type deposits has seen influenced by other heavy minerals present, such as zircon and monazite, but these have been of secondary importance. For most of the sixties and seventies, Australia supplied the 'najority of free world rutile and zircon, and a large proportion of the ilmenite. With the run-down of rutile- rich reserves in eastern Australia, the emphasis has s:iifted in several countries, including Australia, to fill }the gap with i l Wen i to and its derivatives, leucoxene, synthetic rutile and titanium rich slag. over the next 15 - 20 years, as high grade beach placers in Western Australia are mined out, less traditional sources for mineral sands products will be opened up. Low grade placers (particularly those dominated by ilmenite) will be reassessed in Australia, U.S.A., Africa and Asia, and exploration will shift from beach and dune environment, to heavy mineral concentrations in alluvials, lake deposits and continental shelf deposits. At the same time, production of anatase and bastnaesite will be expanded, as required, from the huge resources contained in carbonatites in 3razil, U.S.A. and China.

Jan 1, 1986

THE treatment by chlorination of the Mount Morgan Gold Mining Company's ores was first accomplished, early in 1886, by a works having a capacity of 25,000 tons per annum. Shortly afterwards another works was established, capable of dealing with 50,000 tons per annum. The extraction of gold was originally successful and satisfactory, but running expenses were high, averaging £2 19s. 6d. per ton of ore treated. These works were believed to be the largest chlorination plants in the world at that time. As might have been expected, the mechanical details and chemical process had not been perfected, and, moreover, both works were hurriedly built, and operating expenses were not then considered of such prime importance, as the ore at that time was of very high grade; the large quantities of low grade ore since dealt with not being then considered, since the bulk of it was not even known to be in existence. These two works consisted of rock-breakers, high speed rolls, screens, elevators, &c., for crushing; a large number of small handrabbled reverberatory furnaces for roasting; one-ton chlorination barrels and three-ton leaching vats for chlorination. The transport of ore from crusher to furnaces, from furnaces to chlorination barrels, and the emptying of leaching vats was effected entirely by hand labour. The system of chlorination was what was, known as Mears process, chloride of lime and sulphuric acid being used in the chlorination barrels, and as the time allowed...

Jan 1, 1911

The 5.6 km Canning Tunnel was constructed to improve water supply from Canning Dam to the Perth metropolitan area. The site area is in the Darling Range which is essentially a laterite-capped plateau-remnant underlain by Archaean granitic rocks, intruded by dolerite. Two arrangements were available. After geotechnical investigations which included geological mapping, seismic refraction geo- physics, diamond drilling and mechanical rock testing, a single tunnel was selected in pre- ference to two short tunnels and a connecting pipeline. The tunnel is hydraulically equivalent to a fully lined tunnel 1.83 m in diameter and 5 580 m long. The alignment diverged from a straight line so that the initial upstream section was almost normal to the contours which allowed for minimal support requirements in a weathered zone. Although steel and con- crete lining was needed at both ends, the main section of the tunnel was unlined except for a concrete floor. A sand and rock trap with a capacity of 46 m3 was constructed near the outlet portal to collect debris and sand down to a size of about 2 mm. Portal excavations were in highly to completely weathered rock which extended 56 m into the tunnel at the upstream end, and 18 m at the downstream end. Conventional drilling and blasting were used for tunnel excavation with survey control by laser. Breakage lEngineering Geologist, Mines Department, Perth, W.A.

Jan 1, 1976

By Sheridan GD

Fifteen samples 'of clays and shales from the Adelaide area were selected from a total of 84 as representing material of possible value for the manufacture of light-weight aggregate. A detailed examination of the bloating. characteristics of these revealed four likely to be suitable. for expansion.' in a rotary kiln. One of these, a Tapley. Hill shale., was-fired in an 8 in. diameter rotary kiln, but con-tinuous bloating without ring formation in the kiln was not achieved. Steam,,-oxygen,, sulphur dioxide and carbon dioxide have been, suggested. as the agents of bloating. An examina-tion of .. the evidence : `leads to the conclusion that carbon dioxide derived from. carbonate minerals is likely to be the principal bloating agent. Attempts to bloat clays by the addition of mica were.not successful.

Jan 1, 1963

The treatment of beach sands in'' the Bunbury/Capel' area for the extraction of ilmenite is a very recent development in the mining industry in'J7estern Australia. Nevertheless since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced. The increasing world recognition of W.A. as a major' Iiroducer of ilmenite is due primarily ' to its low chromic oxide. ; (Cr203 content,, 0,03% to 0.04%, combined with a medium to high grade TiO2 content, 54% - 6 , supported by large reserves, a'. stable government with close access to good shipping facilities.. Ilmenite is produced from-these deposits at low-costs, enabling the industry to compete on world markets despite high rates for sea freights because of the distance from.major markets.

Jan 1, 1964

By R D ROSENTHAL

BHP Iron Ore Ltd's Mt Whaleback is the largest single open-pit iron ore mine in the Pilbara region of Northwestern Western Australia. A division of BHP Minerals, one of three core businesses of Broken Hill Proprietary Company Ltd (BHP), BHP Iron Ore - Newman is a joint venture with minor participants C Itoh Minerals and Mitsui. Mine planning for Mt Whaleback generates detailed sequence plans for a long term forecast incorporating equipment requirements, marketing forecasts, and pit development strategy. Utilisation of several computer packages, both commercially available and site modified, are necessary to achieve such a demanding task.

Jan 1, 1992

By J J. Plumb, P D. Franzmann

A study was conducted to describe the microbiology of the MICCL Monywa chalcocite heap bioleaching operation. Microorganisms were detected in the heap using culture-based techniques and cultureindependent PCR-DGGE analysis of the 16S rRNA gene. The metabolic requirements, temperature and pH optima were determined for selected strains isolated from the heap material. Six strains (BH1-BH6) were enriched and isolated from heap solids and leachate samples. Phylogenetic analysis of the 16S rRNA genes showed that strains BH3 and BH4 were closely related to the acidophilic bacterium Acidithiobacillus caldus and strains BH5 and BH6 were closely related to Leptospirillum ferriphilum. The optimum growth temperature for L. ferriphilum was 41.3¦C and the optimum pH range was 1.1 to 1.5. A new species of Archaea was isolated from the heap samples. Cells of the proposed species, Ferroplasma cyprexacervatum (æcyprusÆ L.n. meaning copper; æexacervoÆ L.v. meaning æto heap upÆ), are non-motile pleomorphic cocci, capable of chemomixotrophic growth with ferrous sulfate and yeast extract. Cells grow anaerobically on ferric iron in the presence of potassium tetrathionate and yeast extract as electron donors. Growth occurs from 14¦C to 63¦C, with an optimum temperature of 55.2¦C. The optimal pH for growth was 1.0 - 1.2. The species was phylogenetically most closely related to Ferroplasma acidiphilum with a 16S rRNA gene sequence similarity of 95 per cent. Molecular analysis of mine samples (16S rRNA PCR-DGGE) detected the above-mentioned cultured strains of microorganisms as well as species of Sulfobacillus and other unknown Proteobacteria. The microbial community of the Myanmar bioleach heaps contained similar levels of diversity to a dump bioleach operation in Chile, but contained greater amounts of biomass than another heap bioleach operation in Australia. The operating parameters of the Myanmar heaps (low pH and moderate temperature) have selected for the growth of moderately thermophilic microorganisms that are more commonly found in extremely low pH acidic mine drainage sites than in heap systems. The novel species of Ferroplasma is thought to be involved in the aerobic and anaerobic cycling of iron within the heap bioleaching environment.

Jan 1, 2004

By C Doblin

Any value addition to the mineral sands in the Murray Basin (Australia) will generate waste that needs to be disposed of safely. For example, conversion of ilmenite and synthetic rutile to titania (TiO2) pigment would generate large amounts of environmentally undesirable elements. Processing of U+Th containing zircon sands to zirconia or to higher purity zircon would generate a low-level radioactive waste. In this study it is proposed that one way to circumvent the waste problem could be to contain such waste in magnesium-based (Sorel) cements. Containment of waste in magnesium cements is an attractive idea especially for the mineral sand processing companies that could operate in the Murray Basin in the future, because the required magnesium oxide and magnesium chloride may be made cheaply from the saline waters encountered during mining operations. The magnesium cement production process is also far less energy intensive than the Portland cement production process. The results of this study indicate that mixing a waste stream with a slurry of magnesium cement before being discharged to the disposal area would contain the waste in a æconcrete-likeÆ structure, resistant to dispersion by wind and moderate rain. However, some loss of strength and increased leaching of impurities, Mg and Cl could take place in wet climate areas. Ongoing research is being concentrated to develop a new process for making water-resistant magnesium cement.

Jan 1, 2002

By Watkins JR

The educational system is a dynamic; a flow resource that can be significantly shaped, changed and - refined by educationists. This paper analyses these various facets of geo- science education in Australia. The Australian educational philosophy is essentially a laissez- faire model, a free market approach without any real government or professional directive or stratagem. Students are therefore free to choose their own educational pathway dependent only upon their ability and the access to courses. Geological education at the tertiary level in Australia is described and critically analysed. There is a real need for a rationalisation of geological education in Australia, and this rationalisation should include not only the number of courses offered but should also aim to fully define both the philosophy and purpose of geological education and the accreditation procedures for the Students.

Jan 1, 1986

By R Lastra

Applied mineralogy involves conducting investigations on ores, minerals and materials to solve problems encountered in mining, metallurgy, processing, industrial minerals, environment, health and other fields. The investigations are performed to determine the mineral behaviours during processing by using every mineral and ore characterisation technique and appropriate instruments. As the field is young, new techniques and instruments are still being developed. This paper attempts to convey the scope of the field by:describing the capabilities of the respective research instruments for determining mineral characteristics, summarising investigations of gold as an example of applied mineralogy studies of precious metals, andpresenting a case history where applied mineralogists worked closely with mineral processing engineers on a base metal ore and mill products to help the engineers optimise their processes for maximum recoveries.

Jan 1, 2008

By Campbell R

The use of a 35mm non-metric SLR camera and an analytical plotter to prepare close range photogrammetric (CRP) plans of a quarry and open pit mine face is described. The plans, at scales ranging from 1:5 -1:1 000, were used to measure the orientation of geological structures and failure surfaces in the exposed faces.Details are provided on the equipment used and the field techniques. The method:ò is quick and relatively cheap to perform,ò allows the accurate orientation of specific geological features to be determined,ò provides survey results of suitable accuracy that may be used for detailed geotechnical analyses of pit wall failures,ò shows great potential as a rapid and accurate technique for monitoring changes in pit wall profiles with time.

Jan 1, 1990

By Goldstone A

The paper introduces a newly developed multi-function test rig for fracture grouting. This test rig has many functions and its performance is consistent. It can control and adjust accurately the opening degree of fissures and static pres- sure; it can measure automatically the quantity of grout injected; it can measure precisely pressure drop of grout in fissures; it can test the results of injection, including effective dispersed distance, anti-filtration capacity of consolidated body, mechanical strength, etc. It can inject a single or two grouts into one or several fissures at a pressure of 16 MPa. Therefore, it is an ideal test rig for fracture injection. The paper depicts all the components of the test rig, its performance and application of the results obtained from fracture grouting tests. Examples are briefly described.

Jan 1, 1988

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988

In the retreatment of an old tailing dump containing five per cent of lead principally as lead sulphate, the lead sulphate was floated with liquid Aerofloat reagent after sulphidising with phosphorous pentasulphide in an acid circuit. A zinc middling product was removed by flotation before recovering the lead. Concentrate products were sundried in surface dams.INTRODUCTIONDuring the period between 1917 and 1928 the Junction North Broken Hill Mine N.L. deposited several tailing dumps on its leases, which were acquired by North Broken Hill Ltd.in 1931. One of these dumps lay alongside a main road close to a residential area. The high metal prices prevailing in the post-war years (1945 onwards) provided a strong incentive for retreating this dump and transferring it to a less objectionable site.SAMPLING AND TESTINGIn 1946 a sampling and testing campaign was instituted which culminated in 1949 in a decision being made to erect a tailing retreatment plant adjacent to the dump.The dump was sampled with a 3 in. post hole auger using extension lengths of -! in. pipe for drilling to 30 ft. The dump material was fine and moist and core recovery was excellent. Hole depths ranged from 14 ft. to 30 ft., with an average dump depth of 20 ft.Individual samples were prepared from successive 9 ft.lengths of core and each sample thus obtained was, submitted for sizing and assay.The sampling showed that the dump contained approximately 380,000 tons of fine tailing assaying:

Jan 1, 1956

By Rath M. C, Das R. P

Studies were carried out on dissolution and oxidation of iron powder in ammonia-ammonium carbonate solution using oxygen over pressures. Cobalt and nickel losses during iron oxidation under different conditions were investigated. Regression equations were derived for percent cobalt loss and percent iron oxidation using ammonia, ammonium carbonate and oxygen partial pressure as the variables. The equations were tested for adequacy using Fisher's test. Cobalt losses increased with the increase of initial cobalt concentration and about 400 mg/l of cobalt was lost from a solution containing 500 mg/l cobalt. A maximum of about 80 mg/l nickel was lost from 1 g/l nickel containing solution, and this loss remained the same even when the nickel concentration was increased to 7.5 g/l.

Jan 1, 1992

I have chosen this topic for my address with the intention of preserving a rather extraordinary record of recurrent additions of capital in the financing of one of the world's important silver-lead-zinc mines. The recitation of the trials and tribulations which fore-shadowed the rise of Mount Isa Mines to a position of relative prominence in the realm of non-ferrous mineral production may, I hope, be of assistance to some of the younger members of the Institute who may be called upon during their careers to meet similardevelopmental and financial problems.Mount Isa Mines Limited was incorporated in New South Wales in 1924 with an Authorised Capital of 40,000 shares of £20 each.In November 1925 the Company acquired the leases and water rights of the Mount Isa Proprietary Silver-Lead Limited for 6,250 fully paid £20 shares. Shortly thereafter, but in the same year, the £20 shares were split up into £1 shares, thus bringing the Authorised Capital to £800,000.The leases purchased consolidated and brought under one management the principal ore bodies of the Mount Isa area.Transportation facilities were indispensable to the economic future of the field, so the construction of a railway extending the Government line from Duchess, 54 ,miles to Mo.unt Isa, was assured by the passage of a bill in October 1925 by the Queensland Parliament. Under the provisions of the so-called Mount Isa Railway Act the Company was required to idemnify the Government against national loss on this branch line for a period of 10 years.

Jan 1, 1953

Papua New Guinea is geologically prospective for large, medium and small mineral discoveries. All profitable developments to date have been very large mines but for every large mine there should be many small mines which could be developed under appropriate circumstances.The Papua New Guinea Government should, with appropriate changes to fiscal, legislative and policy regimes, create a favourable exploration envir-onment to encourage a major increase in exploration by small exploration companies and subsequent discoveries and mine development.

Jan 1, 1994

The gold industry has been revolutionized in the last decade by market forces and technological changes. The latter are discussed in this paper, with particular emphasis on carbon-in-pulp (CIP) and heap leaching. The nature and scope of the process development aspects of a gold project are considered, and factors which determine process decisions are outlined, including the choice of CIP versus carbon-in-leach (CIL), agitated leaching versus heap leaching and treatment of ores containing copper and silver. Likely directions for development of gold processing in general are discussed, and metallurgical process options for treatment of ores of platinum group metals (PGM) are outlined.Metallurgical process development for gold and platinum group metals proceeds through a number of well defined stages, with input from various disciplines and information sources. The orientation phase will include preparation of a general project overview; careful consideration of the issue of sampling and sample preparation; characterisation of the resource in terms of ore types, mineralogy, chemical composition; development of appropriate methodology; and development of an understanding of the potential metallurgical unit operations.The process definition phase will be-'directed to development and definition of a notional process flowsheet, and will include identification and appraisal of process options; development of, notional process flowsheets; testing of flowsheets against ore types; ranking of flowsheets; initial engineering, including preliminary mass balances, equipment selection and plant layout; and broad-brush economic appraisal.

Jan 1, 1986