Search Documents

By A. W. CAMERON

Over a 4 hr period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc, and gangue minerals, size by size throughout the whole circuit.Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had some reserve capacity.In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one-third of the lead losses in the final tails.All sizes of zinc values between 100 mesh and 7 microns floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the minus 7 micron fraction.The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

THE manufacture of Portland cement on a commercial basis dates back to the year 1824, when Joseph Aspidin, of Leeds, patented his process. It was, however, only within the past 25 years that the cement of to-day commenced its history, and during that period manufacturers have constantly tried to improve the grade of cement.The introduction of the rotary kiln at the opening of this century was the starting point of rapid development in the process of manufacture, and in the quality of the cement produced.Following on the rotary innovation came the wet process. This at first was used only where the raw materials were of a soft nature; but to-day nearly all classes of materials can be treated by this method. Oompared with the dry process, it allows for greater refinement of raw materials, more intimate mixing, better chemical combination, and economy in fuel. Taking advantage of this, the manufacturers in England and America are in a number of cases substituting the wet for the dry process.Subsidiary machinery throughout the factories, such as crushing and grinding mills, have also been vastly improved. The chemists, too, have done their share in the work. Long and careful research has proved the necessity for accurate proportioning of raw materials, thorough mixing, and very careful burning. All these factors combined have given us the product of to-day, which is consistent within very narrow limits, and far superior to that of the beginning of this cement era.

Jan 1, 1926

By P Vasconcelos, M-F Zhou, X-F Zhao

The eastern part of the Yangtze craton (eastern China ) is marked by a number of medium to small size porphyry Cu-(Au-Mo) deposits. A detailed geochronological study and existing data suggest that these deposits were emplaced in the 144 - 136 Ma interval. They are spatially and temporally related to voluminous mafic and alkaline magmatic rocks ranging in composition from gabbros, syenites, A-type granites and their volcanic counterparts. This indicates that the porphyry Cu-(Au-Mo) deposits in the eastern Yangtze craton were generated in an intra-craton extensional tectonic setting, which is distinctly different from the compressive environment of oceanic or continental arcs of the Pacific Rim where numerous giant porphyry Cu deposits were formed. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Maslowski, J B. Gemmell, D R. Cooke, C Zesati, J Castorena

The Palmarejo, Guadalupe and La Patria Silver-Gold epithermal vein deposits occur in south-westernChihuahua state, Mexico. The veins are hosted in a volcano-sedimentary sequence that comprises andesitic to basaltic resedimented volcaniclastic rocks, together with less abundant coherent and pyroclastic facies and minor red-beds. The host sequence is part of the Lower Volcanic Series, and formed in a magmatic arc environment during the Late Cretaceous to Early Tertiary Laramide Orogeny. The Lower Volcanic Series is overlain unconformably by an extensive sequence of Miocene rhyolitic ignimbrites, known as the Upper Volcanic Series. At this time, it is uncertain whether epithermal mineralisation was related to andesitic intrusions (85 Ma) and/or Oligocene rhyolitic dykes (25 Ma). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

Partnering has come to prominence in the Australian construction industry in a formal sense this decade. The high level of disputation in the building and civil construction industries in the 1980s drove its development in both Australia and North America. PartneringÆs use has been most prominent in the construction industry, particularly in the civil and construction sectors of the industry. It has found favour in some mining development projects, one of the most notable being BHP MineralÆs Cannington project in NW Queensland. This paper examines the requirements of successful partnering agreements and describes in detail the mine development partnering agreement at Cannington. In particular, the paper discusses the authorÆs experience and recommendations for partnering to avoid contractual problems and achieve win û win project outcomes for all parties to major mining projects.

Jan 1, 1999

Contracts are widely used in mining to provide self motivation in an environ-ment of isolated work places. Which incentives to use and how to implement them has long been the subject of numerous discussions. The mines operated by Australian Mining and Smelting at Broken Hill have evolved several guidelines to follow when developing contracts.Identify the main purpose of the work and use this as the basis of measurement for the contract. Therefore stoping achievement would be measured by tonnes extracted, development by metres driven. Paying for other work activities such as standing timber in timber stoping must detract from the percentage of the total contract paid per tonne produced. Concentrating on the main activity and applying the majority of contract pay to that task reinforces at is beneficial to both the miners and the whole operation.

Jan 1, 1985

By J Brisebois

The Wisemans Creek derelict mine site is located in native forest approximately 150 km west of Sydney. Mean annual rainfall at Bathurst, 20 km to the north, is 634 mm and reasonably distributed throughout the year, with slightly more rain falling in the summer months. Evaporation is 1350 mm per annum and considerably exceeds rainfall in all but the winter months (May to August). This results in a water deficit for much of the year. Groundwater is relatively deep, as it has not been intercepted in the shallow open cut workings. Investigation of the groundwater regime was beyond the scope of the current study. Mining has taken place on the site for almost 100 years, during which copper, talc and gold have been sequentially extracted from surface and shallow underground workings. The site is now characterised by the presence of small open pits, unprotected shafts and adits, mullock heaps and an unconfined tailing deposit from a small cyanidation plant. From a distance, the mine area is visible because of two distinct steep bare slopes below the relatively small mine workings and mullock heaps. The mining area was characterised in terms of its environmental, safety and heritage issues. Mullock from the early copper mining was found to be acid forming and leachate from this, combined with clearing of timber, has most likely resulted in death of vegetation below the heaps. The mullock also contains elevated concentrations of heavy metals. The gold tailing is apparently benign and not acid forming, although there are indications of oxidation and acid formation in the derelict gold open cut. Oxidation of the acid forming mullock still appears to be taking place even after being exposed to the atmosphere for at least 50 years, resulting in continued contamination of the slopes below the heaps with heavy metals. The concentrations of metals decreases with distance below the mullock heaps and also is confined to the ground surface the further away from the mullock, providing further evidence to support the theory that the mullock is the source of contamination. Despite this continuing contamination, its spread beyond the immediate mining area appears to have been limited because of the relatively dry climate, with only intermittent rainfall and stream flows. Irregular storm flows in the nearby creek could also have washed any contaminated soil some distance from the site and beyond the area investigated in this study. Remediation of the site and restoration of vegetation on the bare slopes will therefore depend on elimination of the source of acid and metals. Options for remediation, focussing on minimising cost by retaining the materials on or close to the site, are identified. The volume of the open cuts would appear to be close to that required for burial of the acid-forming mullock, thereby removing the source of surface contamination while keeping it above the groundwater table. However, implementation of this remediation plan will depend on the availability of funds to undertake the work through the New South Wales GovernmentÆs Derelict Mines Program.

Jan 1, 2003

By Vanderberg B

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras. Todays common approach of utilizing only a single camera system can, in some cases, lead to great errors and erroneous conclusions when motion is assumed to be in a predefined plane of motion. CMe phrase, "What you see is what you get, it no longer true in 3D."). This is especially true in blasting environments which exhibit complex and/or predominant structural geology. The 3D system eliminates this problem, and includes automatic corrections for vertical and horizontal camera optic axis orientation, dimensional controls, lens distortion, field set-ups, projection imaging and digitized inputs. The only information required is the surveyed or known coordinates of at least six non coplanar points in the field of view. Motitn from each camera view is then digitized, transformed through a direct linear transformation, and processed with the 3D software, which also automatically time matches the data, even when the high-speed cameras are operated at different speeds. Eleven calibration constants are generated using an overdetermined system of linear equations to output the true 3D coordinates of motion in the time domain. Applications for this 3D approach are not restricted to just analyzing the kinetics of a blast. The system is sufficiently flexible to allow an accurate, quick and economical method of bench face profile analysis, generate muck pile profiles and estimate volumetric calculations. The recording systems for these applications can be common 35mm still photography and/or video equipment. It is envisioned that this system will soon replace expensive laser surveying systems at a fraction of the cost in the near future. It is also an excellent system to accurately quantify drill pattern layouts and the spatial locations of each blasthole. This information is required for generating single hole based synthetic seismograms to accurately predict the vibrational outputs of full scale blasts. In terms of litigation concerning claims resulting from blast induced ground vibrations to structures, the system is proving to be an excellent and economical method of performing pre-blast surveys where differential settlement is suspect.

Jan 1, 1990

From 1980 to February 1991 the Rosebery concentrator purchased ore from Aberfoyle's Que River Mine. Following the termination of the contract the concentrator reverted to treating Rosebery ore alone. Since that time it has become apparent that the circuit configuration employed was no longer optimum for zinc metallurgy. The circuit was designed to treat a difficult, slow floating sphalerite; however, the opposite was now found to be true. The sphalerite is fast floating and the circuit was cumbersome. During 1992 extensive circuit changes led to the provision of a simple open circuit flow sheet. The circuit is now easier for operators to understand and lends itself to improvements in process control. Middlings streams have been minimised, which produces a far more stable circuit. Significantly, it must be noted that the key to achieving potential results must lie in reducing variations within the process. A significant ore characterisation program has been undertaken, providing an insight into the metallurgical compatability of the ore to be mined. Using the information collected in this program, metallurgical recoveries and grades can now be predicted with a geater accuracy. Ore characterisation data suggests that an improvement from a 54 per cent zinc concentrate to a 57 per cent zinc concentrate should be achievable. By understanding the size-by-size mineral assemblage, a strategy for concentrate grade improvement has been developed. The requirements of the customer must in all cases determine the quality of the product. Pasminco is a fully-integrated zinc producer and as such significant gains can result by tailoring the concentrates to suit the Smelters.

Jan 1, 1993

Regional problems, such as political risk and debt reschedulings, in Pacific Rim nations coupled with the price volatility of gold mean that multi-faceted financing packages are needed to offset the many risks inherent in a new gold mine development. The cross-border risks of getting money back out of a producing mine may require the involvement of export credit agencies, multilateral government banks, or political risk insurance. Variations on forward gold sales, gold loans, or offset structures can also enhance the flexibility and safety for the providers of both the debt and equity. The region will become as large a gold producer as South Africa by 1990. The large dollar amounts for both investment and revenues realised are of great significance to the economies of many of the Pacific Rim countries especially as a means to increase foreign exchange earnings.

Jan 1, 1987

By Reid JG, Cutfield S

Considerable quantities of dissolved nickel are lost in the waste liquors from the QNPL nickel treatment plant. Cementation, precipitation and ion exchange techniques were investigated to reduce this loss. Ion exchange was the most successful of the procedures studied and a process for recovering nickel from stripped ammoniacal process liquors was developed in the laboratory and scaled up to plant flow volumes. The system developed uses a carboxylic ion exchange resin operated in a completely ammoniacal cycle. The regenerant is itself regenerable using existing plant, thus the only loss is the stoichiometric value of NH4+ required to displace the exchanged cations from the resin. Existing plant sand/anthracite filter beds have been adapted for use as resin columns containing 3 cubic metres of resin capable of treating effluent at a flow rate of 6000 litres/min.

Jan 1, 1978

By Restarick CJ

Plant data are presented which indicate a relationship between flotation rate constants and pulp density in zinc cleaning circuits at Broken Hill. The data were obtained from down the bank sampling of cleaner and recleaner banks at North Broken Hill and New Broken Hill Consolidated Concentrators. It was found that, under normal plant operation, flotation rate constants increased at the lower pulp densities existing in the later cells of cleaner banks. The addition of dilution water to the feed to the bank increased flotation rate constants, thereby confirming the relationship. It is shown that the relationship between flotation rate constant and pulp density is size dependent, being most pronounced for larger sized particles. In contrast, the effect is not markedly dependent upon mineral type. Possible consequences of this relationship for control of cleaner operation are discussed with the aid of some simulated results.

Jan 1, 1978

By M Maulen, K van Olden, T Elkington

A large open pit is planned at the site of an existing underground mine. Strategic planning work has been undertaken to investigate the project value associated with an expansion of underground operations in conjunction with the proposed pit. Previous analysis determined that any depletion of the available pit resource that changes the optimum pushback sequence has a significant negative impact on overall project value. Therefore, to investigate the viability of an underground expansion requires a system to identify the stope resource that would add value to a combined operation if mined ahead of the pit. The key solution to this problem was to generate a resource model variable that defines the blocks, which have greater discounted value if mined by stoping rather than by the open pit. A key assumption was that the open pit is the main driver of overall project value. From the identified potential underground resource, series of mineable stope shells were generated at a range of cut-offs. This stope reserve data formed the input to a mixed integer program based software tool that was developed and used to optimise the underground mining plan, at conceptual level, for various project configurations. A dynamic programming tool was then applied to evaluate the optimum value of a combined open pit and underground operation. The overall objective of this project was to determine the strategic plan that yields the optimum value for a combined undergroundûopen pit operation. The results provided a clear focus and direction for more detailed design and planning.

Jan 1, 2009

By Xaykhamphoune, Ward B

Draglines have been used exclusively for primary overburden stripping at the German Creek Mine complex in central Queensland, where coal has been extracted from a series of ten open cut pits working seams of the German Creek Coal Measures. Due to the dip of the seams, most of the pits have now reached the limit of current economic viability and the emphasis has switched to underground extraction using longwall methods and to a new area of open cut reserves in the nearby Rangal Coal Measures at German Creek East. This area is characterised by weak Tertiary overburden, relatively steep dips and low strength intraformational shear planes at the top and bottom of the coal.The first pit, with a maximum depth to coal of 15 m at the low wall, avoided any major slope failure through use of scrapers to excavate the boxcut and dump the spoil away from the low wall. However, this method was not considered economically viable for the second pit where low wall depths reached 44 m. Following geotechnical investigations the boxcut was divided into a number of zones depending on depth of cover, dip and thickness of Tertiary clay. Slope stability was assessed for each zone using several analytical techniques to ensure that dragline mining would be acceptable. Slope design parameters incorporating various stabilisation techniques, notably an updip trench backfilled with competent spoil to form a low wall buttress prior to excavation of the boxcut panel, were successfully integrated into the mine plan after careful consideration of the complex scheduling to minimise rehandle.

Jan 1, 1992

By Kellerwessei H, Oberheuser G

A major breakthrough in extending the life of the wear material of high pressure roll crushers when treating moist, highly abrasive material has removed the last impediment to the widespread acceptance of high pressure comminution in the minerals industry. The system is very energy efficient. It has been demonstrated that in the cement industry energy savings of up to 50 per cent have been achieved compared to conventional hall milling. Besides being energy efficient, the process provides some remarkable and useful effects; ò better liberation of mineral constituents (as proven for diamond liberation). ò preferential comminution where induced micro fissures follow grain boundaries. ò higher reactivity of the product due to micro fissures. All these points will be described here together with a review of current flowsheet design and incentives for the use of this method of Comminution.

Jan 1, 1993

Open pit planning and scheduling play a significant role in establishing, maintaining and improving the economics of open pit mining ventures.The development of an open pit plan and schedule involves consideration of the following elements:ò the market for the mineral, ò the mineral deposit,ò the treatment process, ò the external factors,ò the mining method,ò the scale of operations, ò the open pit design,ò the open pit schedule,ò the calculation of economic performance, andò the implementation of the open pit plan and schedule.The above factors are described and discussed. Open pit planning and scheduling is the linkage which enables a mineral deposit amenable to open pit mining to meet a market requirement for the particular mineral. To effect this linkage the open pit planner should have a good detailed appreciation of both the mineral deposit and the market.

Jan 1, 1992

By Hall ST, Miles NJ

Recently an inorganic salt, sodium polytungstate (SPT), has become available that allows the preparation of non-toxic solutions of relative densities up to 3.1. It is relatively expensive and at the higher relative densities achievable, highly viscous. Alternative inorganic compounds may in the future be identified that overcome these limitations. The Australian Mineral Industries Research Association Ltd (AMIRA) has initiated a project to examine possible alternatives. However, it has been found that by the addition of finely divided ferrosilicon to solutions of SPT, relative densities of up to 4.0 can be achieved. A laboratory technique for density fractionation of sized mineral samples utilising this finding has been developed. This is currently being extended to study the potential applications of such liquids and suspensions in dynamic systems for mineral, coal and recycled waste separations.

Jan 1, 1993

To secure a sustainable competitive advantage some smelters may need strategies based on flexibility in feed and product ranges depending on immediate future projections of profitability. This paper explores the technical requirements for strategic diversity in smelting, leaving procurement, marketing and contractual considerations aside. The days when a smelting operation is tied specifically to say only processing zinc concentrates are perhaps drawing to a close. While internationally traded mineral concentrates are available, attractive business opportunities must exist for fully diversified custom smelters. Certain new and emerging technologies have inherent characteristics that are evaluated in this context. The paper identifies the basic building blocks that will permit such a scenario and assesses the technical feasibility. The ability to respond flexibly to environmental pressures is highlighted as being of paramount importance.

Jan 1, 1996

By Rowe J

The case study is based on the largest ore deposit at Mt. Lyell; the Prince Lyell deposit, comprising a regular lensoid mass of dissemina- ted and vein pyrite-chalcopyrite mineralisation. Reserve estimation employs conventional techniques, based on diamond drill hole and relevant development sampling data. Probable ore reserves are estimated using the contouring (isoline) method an longitudinal projections for ore thickness and accumulation (m %Cu) at a '0.8% Cu' cutoff. Final stope and pillar res- erve estimates (proved ore) are derived from designed ring tonnages and contoured accumula- tion for individual mining units, following more intensive sampling. Systematic grade control procedures have been adopted and individual stopes and pillars reconciled against mill production. The proved ore estimates have been found to com- pare favourably with the reconciled production.

Jan 1, 1979