Search Documents

By Toop G. W, Martin M. T

At the Cominco Ltd plant in Trail, British Columbia, the Betts lead electrorefining operation requires that antimony and arsenic be present in the lead bullion for anode slimes stability control. Until 1986 the antimony and arsenic inputs from concentrates to the Lead Smelter needed to be supplemented with high antimony and arsenic content recycles from the Silver Refinery operation to maintain a satisfactory composition. Subsequently the antimony and arsenic inputs have increased as a result of increasing levels of antimony in Sullivan lead concentrate and the purchase of larger quantities of silver/gold bearing concentrates that inherently have higher antimony and arsenic levels. The increase has exceeded the limits required by the Betts process. It therefore became necessary to install a partial softening process downstream of the Continuous Drossing Furnace to satisfactorily control the bullion composition. Process control and oxygen injection techniques used in the partial softening process are reviewed. Approximately 8 tonnes/day of softening slag are produced having a combined antimony and arsenic content of 25 percent. This slag is reduced in a recently commissioned short rotary furnace followed by vacuum distillation of the metal for recovery of the antimony and arsenic values.

Jan 1, 1989

By Wright R. J

The Commission called tenders for a four boom hydraulic jumbo, plus basket, on an art- iculated carrier in Sept. 1977. Atlas Copco submitted the successful tender in Jan. 1978 for the supply of a three boom jumbo, plus basket. The Promec TH470 jumbo was commiss- ioned in the 2000 m long Sophia tunnel in Nov. 1978. Adequate spare parts were not available during the first three months of operation and the hammers could not be overhauled at the recommended interval. One hammer was removed after drilling 13 600 m due to a crack in the intermediate housing. Tests were conducted with different types of drilling consumables. Both rope and Hi-teed threads were tested and found compar- able. The average penetration rate in the granite was 1.1 m/min. Initially the drillers were not experienced enough to operate the BUT 15ERH booms without causing damage to the booms and hoses. Drilling deviation espec- ially of the perimeter holes was greater than expected. It is now obvious that greater attention must be given to attracting, train- ing and retaining the right type of operator and maintenance fitter.

Jan 1, 1981

The first record of coal discovery in Australia dates back to 1791 when escaping convicts found coal in the banks of a creek just south of Newcastle. Development in the Newcastle Coalfield was the sole source of supply for the colony and for export until the 1850s when mines were established in the Southern & Western Coalfields. The important Hunter Coalfield was not discovered until 1873 when coal was found at Rixs Creek near Singleton: The first exploration drillholes were commenced in 1799 using drilling equipment obtained by Sir Joseph Banks. From 1820 to 1850 several famous geologists (naturalists), including the Rev W. B. Clarke, J. D. Dana and Strzelecki, wrote reports on the coal measures in New South Wales. The first Government Geo- logist, Samuel Stutchbury, was appointed in 1850. The major coal deposits of the State are contained in Permian Coal Measures in the Sydney-Gunnedah and Oaklands Basins. Coal quality ranges from high volatile, high moisture thermal coal at Oaklands to low volatile hard coking coal in the Southern Coalfield. Most coalfields can provide a range of steaming and coking coals.

Jan 1, 1988

By D Craw, N Newman

Previously published stream quality data and AMD (acid mine drainage) analyses have been collated into a database (DAME û Database for Assessment of Mine Environments) and additional samples including NMD (neutral mine drainage) have been collected from coal mine drainages on the West Coast. Variations in the chemistry of mine drainage samples can be related to four factors: 1.       regional geology (Brunner Coal Measures or Paparoa Coal Measures) 2.       mine type (open cast or underground) 3.       hydrogeology 4.       local geology   In general mines hosted in Paparoa Coal Measures produce NMD whereas mines hosted in Brunner Coal Measures produce AMD with highly variable chemistry. Differences in coal mine drainage chemistry between mines hosted in Brunner and Paparoa Coal Measure sequences can be measured with acid-base accounting geochemistry. Correlation of ANC (acid neutralising capacity) and MPA (maximum potential acidity) analysis of rocks with mine drainage samples is substantially better than correlation of NAG (net acid generation) analysis with mine drainage chemistry.   It is likely that NAG analysis over estimates acid generation potential of some samples due to release of organic acids that are not released under environmental conditions. In general, differences in mine drainage chemistry between Brunner and Paparoa hosted mines are attributed to the effect depositional environment and diagenesis on coal measure composition. Exceptions to generalisations relating mine drainage to Paparoa or Brunner host rocks are likely where local geological conditions cause increased deposition of pyrite in Paparoa rocks and additional analyses are required to confirm interpretations.   Based on the interpretation of these results a mine drainage chemistry hazard model has been constructed. The hazard model predicts likely variations in mine drainage chemistry based on the four factors listed above. The hazard model has implications for mine related water quality risks. For example, ecotoxicity, human health affects and selection of remediation techniques are all sensitive to mine drainage chemistry.

Jan 1, 2006

The Yabulu refinery of Queensland Nickel Pty Ltd located near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation. The economics of this exercise have been considerably enhanced in the past year by changing the project's principal product from nickel oxide sinter to refined high purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site. Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to completely change the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.

Jan 1, 1995

The exploration and mining risks are investigated and compared to the risks of smelting, secondary processing and other normal industrial activities. This study concentrates on the risk before, or at the investment decision. Internal and external risks are distinguished. Internal risks are the risks inherent in every engineering design and common to all projects. The main external risks are the financial risk, changes in prices, location problems and geological factors. Financial risks concern every capital-intensive and export-oriented project and cannot be considered as typical mining risks. Changes in prices, i.e. the market risk, concern every industry using raw materials, but the market risk is especially accentuated in the mining industry. Problems of location and infrastructure are normally more significant in mining than in other projects, and geological risks are unique to mining. All these risks associated with mining projects combine to form a risk at least twice as high as that for other normal industrial activities. Within the range of profitability of mines, which on average is the same as in the manufacturing industry, only a few highly profitable mines exist. These few mines are the sole reward for the high risks taken.

Jan 1, 1986

By Lee H. G, El-Rahaiby S. K

The literature relating to reduction of sulphides by carbon using lime as sulphur-absorbent is reviewed. A stage-wise thermodynamic model is employed to evaluate the practical feasibility of the direct reduction smelting of galena (PbS) concentrates with a carbon reductant in the presence of lime; a coke-rate of 65 kg/ton Pb is predicted by the model. The experimental data on the reduction of PbS:4CaO:4C mixtures under nitrogen were correlated by means of a finite difference numerical method and the values of the intrinsic rate constant I1 were derived. The results for the uncatalysed reduction are represented satisfactorily with log I1 = 1.247(±0.522) - 5540(±610)T-1.The catalysed PbS:4CaO:4C mixtures contained 2.5 wt% of ternary (K, Li, Na)2CO3 catalyst. For the catalysed reduction it was found that log I1 = 3.981 (±0.301) -7790(±353)T-1, where I1 (in both relations) is expressed in moles.(g.C.)-1.atm-1.s -I. The catalytic enhancement faclor was found to be quite large in the 1068 to 1262°K temperature range investigated here.

Jan 1, 1991

This paper outlines some of the recent developments in Spiral Concentrator design, with particular reference to the range of Reichert spirals supplied by Mineral Deposits Limited, typical applications, and test or operating data, are also provided for the different series of spirals now available.

Jan 1, 1978

By N McIntyre, J Smart, J Ossa-Moreno, D Rivera

Hydro-economics is a field of research that analyses water resources from a multi-disciplinary approach (Harou et al., 2009). These models generally include one component that describes the water resources of the catchment being analysed (e.g. the physical behaviour of water), an economic component that describes users’ water demand function (changes of willingness to pay relative to availability) and a coupling methodology. These models go beyond calculating cash flows for water investments and analyse the economic behaviour of users when facing water shortages or surplus. In other words, water demand curves are defined for each water user (e.g. urban, agriculture, mining, environmental and hydropower), and they are used to retrofit the water resources component. As a result, the model approximates the catchment scale response to droughts and wet periods, including the effects of water markets, restrictions, recycling, water sharing and any cooperative efforts by users to adjust to changing climate conditions.These models are usually focused on agriculture and urban users, the main water consumers in most catchments, but they have sometimes included environmental, industrial and hydropower users (Bekchanov, Sood, & Jeuland, 2015). Nevertheless, although a relevant user of water in several catchments, the mining industry has been rarely included. This paper is part of an ongoing project that addresses this gap by developing a hydro-economic model in the upper section of the Aconcagua River in Chile. The aim of the paper is to analyse the sensitivity of the outputs of the model to changes in input data, both hydrological and economic, and to develop insight on usefulness of such models for reducing water conflicts in mining regions.CITATION:Ossa-Moreno, J, McIntyre, N, Smart, J and Rivera, D, 2018. Sensitivity of a hydro-economic model in a mining region to changes in hydrological and economic inputs, in Proceedings Life-of-Mine 2018, pp 52–55 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The design of the grinding section is discussed and details are given of the equipment installed for the autogenous grinding of ores from the C.S.A. mine at Cobar.The first section of the concentrator commenced treating ore in June, 1965 and operating experience and maintenance requirements since that time are outlined.

Jan 1, 1969

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

IA )W cli',hla cn1cnt fault 7011(-s 0 11Cn cOrnprise a nrc,II of inrcIIinkc(I faults, cvtcnqonal shear and In]rck cxtcnsir>nal vein- fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major throughgoing faults. Mesh formation generally involves hydrofracturing (Pf> a3, at least locally) and the condition Pf - 63 to be maintained for the mesh to remain a high permeability conduit, requiring fluid overpressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc.

Jan 1, 1995

Digital computers, by virtue of their capacity for high speed repetitive calculation at low cost, are finding increasing application to routine calcula- tions in the mining industry. In this paper techniques are shown whereby the use of computers can be extended to more complex tasks. The regular calculation of grades and tonnages of material to be extracted from specified areas of an operating open pit is a necessary part of production planning. In this paper it is shown how these calculations can be carried out by computer. thereby freeing planning staff from manual calculation. An operating open-pit mine can be described in terms of drill logs, geological ore boundaries and pit perimeters at various levels. These form the data base which must be suitable for frequent updating to incorporate new information. A suite of computer programmes is described which operates on this data base to calculate tonnages and grades of ore within extensions to the perimeters as indicated to the system by planning staff. Possible future extensions are discussed.

Jan 1, 1971

By Fowler T. J

Examples are provided of discontinuity analysis at selected sites in central Victoria. Discontinuities are rock fractures of low tensile strength, including bedding, foliations and joints, which are analysed during rock excavation design, to quantitatively determine the defect orientations, spacing and lengths. Their analysis can reduce the cost of mining operation and improve safety. Extrapolation beyond the exposed face is required, although difficult without an understanding of the regional geology. For rock engineering purposes assumptions are commonly made that discontinuity characteristics are uniform throughout the rock mass, however this is often invalid, as rock masses have usually undergone large-scale deformation, exhibit anisotropy and inhomogeneity. Structural geologists are able to interpret large-scale deformation responses for the purposes of structural correlation and extrapolation. Examples of discontinuity analysis linked to regional geological assesment from sites in central Victoria, reveal that discontinuities exhibit similar characteristics in a range of rock types of different ages and composition. Spacing variations between individual sites are believed to be a result of local rock type differences.

Jan 1, 1997

Level measurement of underground orepasses is important. Orepasses are not only utilised to funnel ore to the shaft skip loading station but also as silos for storing of ore in order to smooth out ore flow in a shaft system. Safety and operational efficiency are also improved as proper orepass level measurement could prevent overfilling of tipping areas. A study was therefore commenced to determine alternative technologies available as well as identifying practical installations across the Anglo American plc Group. From an instrumentation perspective an orepass system is an extremely difficult environment to take measurements in. Factors like dust, vapour, interference, bridging, wear and physical installation have to be taken into account. The study discusses time-of-flight (ultrasonics, radar and laser) measurement techniques followed by other possible solutions. These solutions included strain gauge measurement, the æjumping monkeyÆ technique, radiotomography, fibre optics and very long baseline interferometry (VLBI). Finally, various South African suppliers have been approached in order to determine instrumentation that is available for orepass level measurement in the marketplace. These recommendations were verified, where possible, by visiting the claimed installations.

Jan 1, 2005

By Gillies A. D S, Supriyadi

The landed cost of coal to the international customer is a major parameter which determines market competitiveness. Rail, port and shipping charges represent 30 to 50 per cent of landed costs for Australian mines selling to Asia. This prop

Jan 1, 1994

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

The Favona Underground Project is located approximately two kilometres east of Martha Mine Open Pit in Waihi, 150 km south east of Auckland, New Zealand.   The underground reserve of 354 koz Au contained in resources of almost 600 koz lies within 600 m of the existing process plant presenting an attractive development target in a challenging environment.   The Martha Mine Open Pit is surrounded by urban housing on the north western edge of Waihi township and the Favona Underground abuts residences on the eastern edge of town. Environmental, community and social licence aspects influence project strategies as the new underground mine extends mining in a town that is planning for closure of current open pit operations in late 2006.   The Favona Underground Project has successfully passed through a detailed feasibility study, the third stage of the five stage Newmont project appraisal system. Methodologies used in the feasibility study and parallel permitting draw on a high level of stakeholder involvement to streamline the development and permitting phases.   This paper discusses the project appraisal process and design innovation required for developing an underground mine adjacent to town.

Jan 1, 2004