Search Documents

Pike River Coal Limited is in the process of developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction. The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park.   As such, the major restriction to planned extraction is protection of: +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2006

By C Sellens, L D. Fabbro, S Vink

The Fitzroy River Aqua-Eco Health Project is a collaborative research project between the Central Queensland University, the University of Queensland and BMA. It is designed to assess the aquatic ecology and health of the streams within the Fitzroy catchment located adjacent to mine sites. The universities are conducting an independent sampling program expected to yield the most comprehensive monitoring to date. The project design incorporates in situ testing of water quality variables including temperature, dissolved oxygen, conductivity, oxidation reduction potential, pH and turbidity. Water and sediment chemistry incorporate testing for sulfate, suspended solids, nutrients and metals. This sampling is complemented by quantifying changes in the abundance and diversity of a wide range of biota, including microbial, macro invertebrates and fish.This paper will detail the program and highlight some of the particular difficulties in conducting this type of research in ephemeral stream systems. Case study examples will be used to illustrate insights being gained from the program. CITATION:Fabbro, L D, Vink, S and Sellens, C, 2013. The Fitzroy Aqua-Eco Health Project, in Proceedings Water in Mining 2013, pp 117-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By R L. Chaney, M Mahoney

Mine and ore beneficiation wastes and smelter contaminated soils often cause phytotoxicity and threaten adverse environmental effects if not remediated. Science has clarified both the risks from soil metals and methods to alleviate those risks that can be applied at low cost. Phytoremediation is a family of plant and agronomy based technologies to deal with environmental aspects of sites requiring remediation. If valid risk assessment indicates that metals comprise risk, phytostabilisation may be used to alleviate that risk for most contaminated sites. In particular, Zn-Pb, Cu and Ni mine and smelter sites are readily remediated by making the soil calcareous and fertile, with added organic and metal sorbent amendments that include soil microbes to ‘revitalise’ the soil. In each case, the soil fertility and causes of phytotoxicity should be clarified by agricultural soil extractions, and the combination of amendments required to improve fertility and reverse phytotoxicity identified and found locally. In contrast with phytostabilisation, phytoextraction/phytomining uses rare metal hyperaccumulator plants and agronomic management to maximise annual phytoextraction of soil elements into plant shoots for harvest, ashing and use as a metal ore. Plants that accumulate more than two per cent Ni in shoots, and yield 10–20 t ha-1 dry biomass yield 200–400 kg Ni ha-1, which has value greater than all common agricultural crops. Considering the value of elements, existence of hyperaccumulator plants and demonstrated agronomic management for Ni phytomining, it is clear that mine sites and Ni mineralised subore-grade serpentine soils can be phytomined economically as an agricultural mining technology. A team developed agronomic methods and improved cultivars of Alyssum, which can be profitably grown on temperate zone Ni mineralised or contaminated soils. Plant species for tropical ultramafic soil materials have been identified. Phytoextraction is also strongly needed to remove Cd from rice soils to prevent human disease from soil Cd.CITATION:Chaney, R?L?and?Mahoney, M, 2014. Phytostabilisation and phytomining – principles and successes, in Proceedings Life-of-Mine 2014 , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D L. Reid, G Nwaila, J Petersen, J-P Franzidis, Y Ghorbani, M Becker, F C. de Beer, L C. Bam

Traditional methods of gold extraction have involved comminution and processing via cyanide leaching, all of which are associated with energy, cost and environmental implications. Subsequently, numerous opportunities for improvement and optimisation strategies in gold mining and processing have been explored, including heap leaching, which has significantly lowered comminution costs. This paper explores the effect of the more energy efficient high-pressure grinding rolls (HPGR) on the comminution behaviour (especially on the crack density) and cyanide leaching performance of laboratory reactors study on run-of-mine gold ore comprising the Ventersdorp Contact Reef (VCR) and the Elsburg Reefs (ER), sourced from Carletonville in the Witwatersrand Basin in South Africa. The ore was comminuted using HPGR at three different pressure settings (120, 90 and 60 bar). Large (-16/+11.2 mm) and small (-5.6/+4 mm) particles of the HPGR product where then mineralogically characterised using optical microscopy, quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) and X-ray computer tomography (CT) before cyanidation. The results of the leach experiments indicated a correlation between gold extraction, particle size and crack density. Mineralogical characterisation of the ore indicates that the Fe-sulfides present in the VCR are likely to be more reactive than those in the ER, thus having a more favourable influence on gold cyanidation. Overall, the results show promise for the heap leaching of Witwatersrand gold ores prepared using HPGR and demonstrate the value of a multi-disciplinary geometallurgical approach.CITATION:Nwaila, G, Becker, M, Ghorbani, Y, Petersen, J, Reid, D L, Bam, L C, de Beer, F C and Franzidis, J-P, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 75-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S Worden, A Lee Zhi Yi, E Sellers, G Corder, A Littleboy

The global shift towards decarbonisation is driving competition for the extraction of critical minerals such as nickel, lithium, and copper. To meet this demand, new mines are being developed while mines approaching closure are being reimagined as sites of potential resources. This reimagining challenges how mine closure is being conceptualised. In the conventional case, when a mine reaches the end of its economic life, it is closed or put into care and maintenance until it transitions to the next land use, such as agriculture, native ecosystem corridors, solar farms or integrated eco – precincts (Murphy et al, 2019; Holcombe, 2020) (the authors acknowledge that unplanned mine closures have left a devastating legacy of contamination, safety and cultural heritage impacts). Extracting minerals from closed or closing mines will extend mine life and, therefore, delay relinquishment and transition. In this context, innovative technologies are needed to make mining economically viable. In the first year of her doctoral research on improving stakeholder engagement in mine transitions, Lee Zhi Yi has coined the term ‘mine life extension technologies’ (MLETs) to describe a class of technological solutions that optimise extraction of resources after a mine reaches the end of its economic life. Examples of MLETs include agromining (van der Ent et al, 2015), in situ recovery (Robinson and Kuhar, 2018), and reprocessing or reuse of tailings (Gou, Zhou and Then, 2019). MLET extraction offers several benefits compared with conventional mining processes, such as waste remediation, value recovery of minerals, a smaller footprint and less environmental impacts (Sellers, Picorelli and Salmi, 2022). What requires further investigation is the consequences of MLET implementation to host communities or community perspectives towards the proposed technology and subsequent delays in transition.

Aug 2, 2023

By W Valery, A Jankovic

A growing demand within the minerals industry for sustainable development and the introduction of carbon taxes have resulted in a significant focus on improving the energy efficiency of comminution circuits. However, in this drive for improved energy efficiency the role of classification has been overlooked. Inefficient classification and large recirculating loads reduce circuit capacity, result in over-grinding and higher specific energy consumption.It is well understood that classification increases mill capacity; therefore, closed ball mill-cyclone circuits have become an industry standard. However, due to limitations in cyclone classification efficiency, the optimum recirculating load is limited to about 250 per cent. A simple relationship quantifying the effect of classification efficiency and recirculating load on grinding circuit capacity is presented in this paper. The possibility of improving the capacity of ball mill circuits by improving classification efficiency is discussed, considering the current practical limitations of classification equipment. Simulation tools were used to evaluate circuits with cyclones and with high frequency screens to identify opportunities to improve energy efficiency. The investigation also identified potential benefits to flotation recovery due to a reduction in over-grinding.CITATION:Jankovic, A and Valery, W, 2012. The impact of classification on the energy efficiency of grinding circuits - The hidden opportunity, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 65-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Beck

Open access to forecasts of mine geotechnical performance in the form of open databases of model results has been considered risky in the past, with a concern that the results will not be understood or will be misused. However, some modelling techniques allow very high similitude modelling of mine deformation and the results can be presented as deformation, damage and other parameters which are unambiguous and which all engineers can be more easily trained to understand. With some effort, sufficient reliability and quantifications of error are possible to overcome many of the issues.Allowing more members of the planning team to have direct access to forecasts of mine deformation will promote awareness of geotechnical issues and will act as a mechanism for improving mine designs. The models will also be more easily integrated into quality assurance programs, by providing a framework for understanding measurement results.The sufficiency requirements for undertaking simulation aided mining engineering will be presented, included some conclusions about requirements for training, quality standards and software development.

Mar 21, 2011

By J Heyes, R Getty, M Sanapala

Closure is an inevitable part of the life cycle of every mine. Successful closure outcomes critically depend upon early and ongoing integration of closure planning and mine planning. Early and holistic integration minimises residual risk and maximises opportunity to leave a cost-effective, positive legacy for the company, investors and future land users. Both disciplines are inherently interconnected and aim to maximise ‘value’ via trade-offs. Historically, integration of closure into mine plans has been poorly implemented across the industry. There is still a perception that closure planning only starts as the end of a mine life approaches. This inevitably leads to tension when making business decisions, with progressive closure often being deferred due to short-term drivers and incentives. To create a positive legacy after production has ceased, this tension can be managed by transparently and fully informing business decision-makers, such that the impacts of short-term decisions on long-term closure objectives are understood. BHP recently updated a business-wide standard ‘Our Requirements for Closure and Legacy Management’ designed to strengthen collaboration, education and integration of closure across the entire life cycle of the asset. Concurrently, the ‘Life of Asset’ definition was refined to include the postproduction phase, until closure objectives have been met. This paper discusses the criticality of mine planning integration with closure and how updates to Our Requirements sharpen the focus from transactional to transformational planning. These concepts are applicable to any mining operation aiming to achieve successful closure across the full asset life cycle, from exploration to post-production.

Sep 18, 2023

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M A. Rhamdhani, R Z. Mukhlis

Removing the ledge formation in the Hall-Heroult cell during the electrolysis process may significantly reduce the energy requirement of the aluminium production process. In the absence of the ledge, however, the sidewall-material types become heavily restricted since the cryolite is very corrosive at the electrolysis temperatures. This paper study the corrosion behaviour of sintered nickel ferrite, nickel aluminate, and magnesium aluminate refractories (as possible candidates for sidewall material) in molten aluminium and cryolite melts with various alumina content at 980°C. Immersion tests of refractories with various porosity were conducted to assess the suitability of the refractories in the corrosive environment of the electrolysis cells. Microstructural change of the refractory after immersion were analysed using secondary scanning electron microscopy (SEM). Sampling of the melts were taken at 0, 10 min, 30 min, and each hour up to 6 hrs, and subsequently analysed by Inductively Coupled Plasma (ICP) spectroscopy. Based on the projected concentration of the refractories constituents in the melts, it was predicted that the corrosion rate of NiFe2O4, NiAl2O4 and MgAl2O4 in cryolite with 11 wt per cent Al2O3 were 461 × 103, 1.03 × 103, and 798 × 103 cm/a, respectively. Much lower corrosion rate of 2.3 cm/a for NiFe2O4, 2.6 cm/a for NiAl2O4 and 0.3 cm/a for MgAl2O4 were predicted if the refractories in contact with aluminium melts. Erosion played an important role in the corrosion as the concentration of the refractory constituents in the melts were beyond its solubility limit. It is therefore crucial to increase the densities of the refractory and improve its wetting characteristics.

Aug 21, 2024

By B Vorster, T Medhurst, A Huey

Roof conditions at Oaky North Mine can be prone to stress related damage and/or time dependent degradation. The ability to identify these areas prior to mining has proved challenging using traditional methods. To help alleviate this situation, a study was initiated to investigate methods for roof characterisation using geophysical logs. This involved the use of neutron log data to provide an indirect measure of the proportion of carbonaceous/micaceous laminae present in the immediate roof strata. Detailed analysis of the shale–porosity inter-relationships arising from this analysis provided a means to estimate the proportion of laminations for a given roof interval. This paper outlines the process and how it was used to improve the current GSR modelling and hazard mapping process.

Nov 29, 2022

By R Verreet

In April 2000 Mount Isa Mines installed hoist ropes of a new design on the double-drum winder at their P49 shaft. The ropes, CASAR Duroplast, were about three times as expensive as the previously used triangular strand ropes. The P49 shaft is situated at Mount Isa MinesÆ George Fisher Mine, located some 30 km north of Mt Isa. This shaft used the tried and proven 6 x 33 triangular strand style ropes. The rope life attained by these ropes at the time was acceptable due to many years of satisfactory performance. The following study indicates the improvement of service life using CASAR Duroplast rope in P 49 shaft, which depends on shaft and winder parameters of that particular shaft and cannot necessarily be generalised to other shafts.

Jan 1, 2005

By J Jasper, L Koroznikova, J Begelhole

This paper outlines a comparison of heavy liquid and heavy suspension separation methods for iron ore characterisation.As part of Arrium MiningÆs program to improve its knowledge of ore types being processed in its two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed for the upgrading process has become a major focus.Iron ore deposits almost always contain more than one valuable (and relatively dense) iron mineral. Iron ores are found with a range of iron contents, giving rise to density variations.At present the industry relies on heavy liquid separation techniques for the evaluation of iron ore samples arising from exploration, mining or metallurgical processes. There are only a few high-density liquids available, which are both high-cost and highly toxic.Low-toxicity solutions that can be utilised at relative densities up to 3.0 have been developed. However, highly-toxic organic liquids are required presently to achieve relative densities beyond 3.0.Bromoform which has a specific gravity (SG) of 2.89, and diiodomethane (SG 3.31) are commonly used; both present significant health and safety hazards.æClericiÆs solutionÆ (mixtures of thallium formate and thallium malonate) provide liquids having specific gravities between 4.0 and 5.0. ClericiÆs solution is highly toxic and testing is currently conducted by a limited number of laboratories worldwide.An alternative to ClericiÆs solution and organic liquids is a low-toxicity, high-SG, suspension technique, which has been demonstrated successfully for heavy mineral sands. This heavy suspension method employs mixtures of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions.Heavy liquid separation is not commonly used as part of routine iron ore feed characterisation due to the expensive, toxic and time consuming nature of the technique. Our results show that the heavy suspensions method can achieve low-cost, low-toxic separation and are outlined and results compared with results using ClericiÆs solution presented.Heavy suspension technique provides a theoretical/absolute separation of a particular sample. By placing an iron ore sample in a suspension of a particular density, it produces two products: a sink fraction and a float fraction. As iron oxides-hydroxyoxides are denser than the gangue minerals associated with the ore, particles that have high iron content will sink and the particles with gangue association will float. This process is repeated over several densities, thus also enabling separation of the constituent iron ore phases. A theoretical grade and a theoretical mass recovery can be calculated. With these calculations, a grade-mass recovery curve can be constructed for any element that is of interest.This type of characterisation can be used to either prepare OBP feed-piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved on a continuous basis.CITATION:Begelhole, J, Jasper, J and Koroznikova, L, 2013. Application of the heavy suspension technique for ore beneficiation plant feed characterisation from the Southern Middleback Ranges, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

pNumerical modelling has been used to examine the relationship between the results of two commonly used methods of assessing the propensity of coal to spontaneous combustion, the R70 and Relative Ignition Temperature tests, and the likely behaviour in situ. The criticality of various parameters has been examined and a method of utilising critical self-heating parameters has been developed. This study shows that on their own, the laboratory test results do not provide a reliable guide to in situ behaviour but can be used in combination to considerably increase the ability to predict spontaneous combustion behaviour./p

Jan 1, 2005

This paper reports the advances made during the development of underground mine fill technology from circa 1960 to the present and, in particular, indicates where increased input from process plant metallurgists û mainly milling, but also smelting û can contribute to further advances. Fill types pertinent to the discussion are partially deslimed, partially dewatered mill tailings fill (uncemented, cemented) and paste fill. Pertinent process plant includes hydrocyclones, thickeners, filters, elutriation tanks, holding tanks, mixing mills, pumps and pipes. Control instrumentation is a critical component of each of the process plant units. The impact of smelter practice on filling is not considered in this paper, except to note that some smelter slags are, or have the potential to be, active pozzolans and when ground to the specific surface area of Portland cement can act as partial Portland cement replacements, a factor of economic and operating significance when Portland cement supply lines are considerable and/or tenuous. The important role of process plant metallurgists has long been recognised, with Thomas, Nantel and Notley (1979) including them as one of the many categories of professionals with contributions to make. With the ever increasing sophistication of mine fill practice and its ever increasing acceptance as an essential component of the mining/ milling/waste disposal process, the scope for contributions by the modern breed of highly educated, specifically trained process plant metallurgists is becoming ever increasingly obvious.

Jan 1, 2006

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015