Search Documents

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

By Grieve BL

For a blast to be successful both heave and fragmentation must be satisfactory. Amongst the major factors influencing blasting are rock properties. This paper considers the effect of rock density on fragmentation and heave and how better results can be achieved in dense ore. Patterns which increase the heave and give better fragmentation are examined and the application of theory to the blasting of the Dales Gorge Haematite, density 4.2 - 4.5 t.m.,3 is then discussed. The drilling of staggered patterns instead of square patterns and a shallower 'V' initiation system has given better heave and fragmentation. This practice has re- duced backbreak and improved toe conditions; these factors have resulted in increased load ing rates. There has been an increase in the lump/fine ratio which is consistent with the theory although other factors such as ground conditions could have contributed.

Jan 1, 1978

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By Yates M. G, Rowlands A. T

Most geostatistical techniques applied to the estimation of ore reserves assume relatively unifonn grade and thickness within an ore deposit environment. In shear-hosted mineralisation this rarely occurs. The distribution of mineralisation is controlled by the kinematic and geometric variation within the shear zone. Although the kinematic variation is dependent primarily on the temperature (and consequently the depth) of formation of the deposit, the geometric variation appears to be relatively insensitive to this parameter. Shoot mineralisation is controlled either by the intersection of secoodary shear planes (brittle deformation) or the stretching lineation of the mylonitic fabric (ductile defonnation).Once the shear geometry is clearly identified, it is critical to review the distribution of grade and thickness of mineralisation. The practice of cutting high-grade intersections without reference to the shear model leads to underestimation of the amount of gold in the deposit. High-grade shoots may occur as pipe-shaped bodies within the system; their identification is essential for both resource estimation and mine planning purposes.

Jan 1, 1991

By M Fewings

This paper casts a light on the sometimes murky world that lies between base metals product æout the gateÆ, and money in the bank. Whether your base metals are leaving the mine as a refined product, or as an ore or concentrate, the generally accepted method of value determination is a London Metal Exchange price, usually measured at some point after the material has left your control. In this paper, the structure and operation, regulation and the reasons for the use of the London Metal Exchange are explored. In addition, the risks and opportunities that terminal market pricing provides to mine managers are explained, with particular reference to hedging. The paper also deals with the structure of the sales contract, including management of shipping issues, agreement of delivered quality, documentation and administrative issues. The selection of counterparties, the role of traders in the market and the growing influence of China and India as base metal consumers and competitors are also addressed.

Jan 1, 2006

By Bell MG

At various decision points in the development of a project, a developer, joint venture partner or financial institution may require an independent review of the basic assumptions and technical aspects of the project. This type of review or technical audit is becoming a more common feature of the project development process. This feature has evolved because of the need of investors and lenders to be more confident of the viability of a project by the confirmation of its technical and cost aspects. Technical Audits offset some uncertainties introduced by the combination of longer development periods for, projects and the highly dynamic world economic scene. This paper reviews the place, nature and process of the technical audit by examining the circumstances when it might be needed, the typical scope of work or brief, the responsibilities of and relationship between the auditor and the client, and the auditing procedure. Detailed aspects of technical audits are discussed followed by a case study of the Hail Creek Coal Project Audit.

Jan 1, 1983

Attention is given to three possible alternative structures namely corporate joint venture, partnership joint venture and unincorporated joint venture. A corporate joint venture involves the formation of a separate and distinct legal entity with limited liability. The shareholders of the Company will be the members of the consortium. A partnership joint venture involves the members of the consortium joining a formal partnership. The partners will conduct the business in common with each other and will share the profits and losses of the project activities. The partners will be jointly and severally liable. An unincorporated joint venture is distinct from a partnership. The members of the venture will not be jointly and severally liable. Taxation and accounting aspects are examined and an outline provided of a typical joint venture agreement. The two main advantages of an unincorporated joint venture are considered to be a favourable treatment for income tax purposes and a greater degree of flexibility when compared with the corporate joint venture and the partnership joint venture.

Jan 1, 1983

With the proclamation of the Environmental Protection Act, 1971-80, the Environmental Protection Authority and Department of Conser- vation and Environment were established to enhance the quality of the environment. Proposed gold developments of all scales can be referred to the Authority in the form of a Notice of Intent. Environmentally significant projects might then require preparation of an Environmental Review and Management Programme. Current environmental issues include the'effects of clearing by prospectors,, mine dewatering and tailings disposal. INTRODUCTION In the past, the environmental aspects of gold industry related activities have received little attention. However, with the proclamation of the Environmental Protection Act, 1971-80, mechanisms were instituted which allowed both for referral of projects to the Environmental Protection Authority (EPA) and establishment of the Department of Conservation and Environment. As well as providing assistance to the EPA on referred projects, the Department is concerned about a number of environmental issues associated with the gold mining industry.

Jan 1, 1982

There are three major human resource management activities which, depending on how well they are done, impact on the performance of people and therefore the bottom line. These are: ò recruitment; ò training and development; and ò performance appraisal. Most sizeable organisations would say they are involved in all three, but there are many more that would admit that their human resource management practices are limited to recruitment. If we concentrate on the organisations that currently undertake all three, we have to ask, `Are they using different systems/benchmarks for each activity, or is there congruence between the activities?'. Our experience is that most organisations use different systems/benchmarks. The end result is: ò one set of criteria to recruit staff; ò another to identify their training needs; ò and yet another set of criteria to measure their staff's Performance.

Jan 1, 1995

By P C. Pistorius

Previous mineralogical investigation of all effluent flotation streams of Mimosa mine (Zimbabwe) indicated that appreciable amounts of liberated platinum-group minerals (PGMs) of the Pt-Pd-Bi-Te class are not recovered û despite electrochemical measurements showing interaction between xanthate and such minerals. In this work, the flotation recovery of synthetically prepared Pd-Bi-Te was compared with that of chalcopyrite (a typical fast-floating mineral) and pyrrhotite (a typical slow-floating mineral), with microflotation tests. These indicated Pd-Bi-Te to be a fast-floater with flotation rates exceeding that of chalcopyrite. Predicted flotation rate constants (from the Ralston model) were significantly lower for small particles (with diameters similar to those lost to the effluent streams) compared with those of particle with intermediate sizes. This supports the suggestion that losses to effluent streams are caused by particle size effects.

Jan 1, 2005

Extensive geophysical exploration and drilling operations have been: conducted in, South Central Queensland by Phillips Petroleum Company and Sunray DX Oil Company since late 1959. The main outlines of subsurface geology are now known, but many problems must be solved before a comprehen sine. picture can be presented of the geology and petroleum prospects e Interpretations to date suggest that -fiddle Paleozoic sedimentary rocks, probably, related to the Tasman belt of geosynclines, once extended. over. most. of the area An oro;eny 2.n late Paleozoic time, succeeded by deep pre-Pexmian erosion, removed the older sediments over large. areas, but Paleozoic sediments, were preserved from erosion in the Adavale and ancillary structur-a.l basins. Marine sediments of Devonian age are con-sidered prospective source beds for petroleum. Current work is directed toward finding favorable structure and reservoir beds to test the oil prospects of the area.

Jan 1, 1962

By M Miettinen

That microorganisms, both living and dead, and products derived from the organisms, can function as flotation agents and flocculation agents is abundantly clear. They can modify the surfaces of minerals. They can function as flotation collectors and as flotation depressants and activators. In many cases they or their products can function as specific flocculation agents. Problems that must be solved before such microorganisms or products from the organisms can be used in commercial operations include culturing the organisms at a cheap cost and reduction in dosages required for various separations. These tasks are formidable. However, the concept of using such natural materials in place of various chemical reagents that may be toxic is very attractive. An attempt is made to show some of the promise of microorganisms in mineral bioprocessing and to consider the problems that must be overcome before commercial application of the technology is realised.

Jan 1, 2005

Coal water mixture (CWM) is a mix of finely ground coal with water and a small amount of chemicals. It is a new way of transporting and handling coal. CWM can be transported, stored and burned like fuel oil in steam generating boilers. It also has some environmental advantages over both oil and bulk coal. A group comprising Ube Industries Limited, Nissho Iwai Corporation (both from Japan) and Coal & Allied Industries Limited has been working in Japan and Australia since 1987 on a joint feasibility study into the production, transport and marketing of CWM from Australia to Japan. The group has been studying the development of a large-scale CWM plant on Kooragang Island at the mouth of the Hunter River at Newcastle, NSW. The project concepts and engineering plans for the CWM plant are well advanced and other studies related to the project are continuing.

Jan 1, 1995

By Ellyett C. D

This paper is an appraisal of the application of optical-mechanical-scanners operating in the non-photographic infrared wavelengths (3-5 and 8-14 micrometres) to mineral exploration in Australia. Pundamental principles of the operation of airborne scanners and their data output, thermal infrared (IR) imagery, are summarized. It is contended that thermal IR imagery often depicts the distribution of electromagnetic radiation emitted from earth surface materials better than aerial photographic techniques because optical-mechanical-scanners sample wavebands which straddle the wavelength peak of earth surface emission. To illustrate the geological features which such scanners can depict, reference is made to thermal IR imagery of a number of areas in Australia where the technique has been applied for exploration purposes. The images demonstrate that this technique can detect structural features like faults and folds, stratigraphic data by distinguishing different rock types and delineating their

Jan 1, 1973

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

By Q Zhou, Y Ma, J Zhu, R L. Frost, P Yuan

A series of organoclays with different surfactant arrangements were prepared by ion exchange. The resulting organoclays were investigated using a combination of characterisation techniques, including X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric measurement (TG) and N2 adsorption-desorption. In the present study, the pores within the organoclays were discussed on the basis of the micro- structural parameters, including BET-N2 surface area, pore volume, pore size, surfactant loading and distribution. The results show that both BET-N2 surface area and pore volume decrease from low to high packing density of the surfactant as the average pore size increases. Two basic organoclay models were proposed for hexadecyltrimethyl- ammonium bromide (HDTMAB) modified montmorillonites: 1. the surfactant mainly occupied the clay interlayer, and2. both the clay interlayer space and external surface were modified by surfactant. This study demonstrates that the pore structure of the resulting organoclays has a significant influence on the sorption efficiency and mechanism of p-nitrophenol onto the organoclays.

Jan 1, 2008

In this paper the reactions which may lead to particle hydrophobicity/hydrophilicity as a function of grinding environment-are reviewed. The results of pulp chemical investigations related to a Cu-Pb-Zn ore on a pilot plant scale and laboratory tests with a Pb-Zn ore to evaluate the effect of some inhibitors on grinding/flotation are presented. The flotation recoveries of the ores treated by conventional and autogenous grinding methods show only a marginal difference and the results favour autogenous grinding. Iron originating from several sources manifests in the form of insoluble hydroxy complexes in the pulps. Such metal hydroxy complexes are hydrophilic and coat the mineral surfaces indiscriminately. On the other hand, selectivity is a problem for pulps ground by autogenous milling. Some corrosion inhibitors used in the laboratory grinding/flotation tests on a Pb-Zn ore showed maximum reduction in the wear of the grinding media ranging from 25 - 36 per cent, depending on the type and concentration of the inhibitor.

Jan 1, 1993

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100% recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after twelve years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Fabjanczyk MW, Guy RJ, Tarrant GC

The design of the reinforcement systems required to stabilise mine roadways has developed through the application of field measurement techniques. These techniques have allowed the level of security of a given opening to be determined from an assessment of the loading within the reinforcement, the extent of roof deformation and experience. The design systems developed are now used extensively in a wide variety of geological environment. Recent interpretative techniques have been developed to improve the level of confidence when designing roadway reinforcement. The techniques are particularly applicable for roadways subject to either weak materials or extreme stress levels. A second area of application is where roadway advance rates and hence the timing of reinforcement placement are critical. The newly developed techniques include both analytical and computational models. The validated computational techniques allow a more rational approach to investigation of the effect of varying reinforcement type, timing of placement and density on the level of stability achieved.

Jan 1, 1992

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985