Search Documents

By Morris P. H

A trial embankment was constructed using coarse coal mine reject on a deposit of crusted coal mine tailings at New Hope Colliery, located in the Bundamba District of the West Moreton Coalfields in South East Queensland, Australia. The purpose of the trial embankment was to assess the load carrying capacity and settlement behaviour of the crusted tailings, including an assessment of strength gain in the tailings under the influence of the fill. Prior to construction of the trial embankment, a site investigation of the tailings deposit was carried out. This comprised vane shear strength testing, together with disturbed sampling and undisturbed block sampling for the purposes of laboratory testing. Following the site investigation, settlement plates and standpipes were installed at various depths and locations within the tailings in the vicinity of the proposed embankment. The instrumentation enabled the magnitudes and distributions of settlement and pore pressure within the tailings to be determined during and following construction of the embankment. The embankment was constructed using coarse reject in three equal lifts to a height of 3.0 m. The tailings sustained a maximum settlement under the weight of the fill of 290 mm, representing about 4.2 ii of the average initial thickness of the tailings and a loss of embankment height of about 9.7 %. By the end of the monitoring period the strength of the softer tailings underlying therust had roughly doubled under the influence of tha cmbarikment

Jan 1, 1990

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By M I. Pownceby, A Guiraud, S Purohit

Sticking and breakage of iron ore pellets during high temperature reduction can result in several operational challenges during shaft furnace ironmaking. With the shift to H2-based DRI processes and decreasing iron ore quality, this issue becomes more prominent. It is therefore important to understand how the iron ore chemistry and mineralogy affects the sticking and breakage of pellets inside the shaft furnace. This study provides a review of the mechanisms that lead to sticking and breakage of pellets inside the shaft furnace. The sticking index of pellets is related to the rate of metallic iron production as well as the precipitation morphology of product iron. Sticking of pellets is also enhanced by the formation of low-melting slag phases. The breakage of pellets inside the shaft furnace is often associated with the mechanical load of burden and pellet swelling, which is caused due to iron whisker or protruded iron formation. This paper investigates how the composition of iron ore, particularly the presence of different impurity oxides such as SiO2, Al2O3, MgO, CaO and alkali oxides in the pellets, influences the sticking and swelling indices. The effect of ore mineralogy on these adverse behaviours is also discussed.

Sep 18, 2023

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By Nakajima A

Some attempts were made to recover uranium from aqueous systems by using various biosubstances including microbial biomass. Of hundreds species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stutzeri, Neurospora sitophila, Streptomyces albus and Streptomyces viridochromogenes. In parallel to this research, various kinds of biomass and commercially available crude drugs were screened to measure their abilities to adsorb uranium. Of these biosubstances tested, high uranium adsorbing ability was observed in chestnut skin, Comi fructus, Geranii herba and Chaenomelis fructus. From these results it may be considered that the uranium adsorbing ability of these biosubstances is due to the following; the uranyl ion is co-ordinated by the polyphenolic compounds such as tannin existing in the biosubstances. Along with these fundamental researches, we have developed a new adsorbent, the immobilised persimmon tannin (kakishibu tannin), for uranium and thorium. This adsorbent can accumulate 1.71 g of uranium per gram of the adsorbent (14 mEq/g), and the uranium adsorbing capacity of this adsorbent exceeds by several times that of commercially available chelating resins (2 - 3 mEq/g). We attempted to recover uranium from uranium refining waste water by using the immobilised persimmon tannin. As a result, the immobilised persimmon tannin can recover trace amounts of uranium from uranium refining waste water containing 10 - 15 ppb uranium with high efficiency. Almost all of the uranium adsorbed onto the adsorbent can be desorbed by washing with 0.05 - 0.1 M HCl or H2SO4. Thus, the immobilised persimmon tannin can be used repeatedly in the adsorption-desorption Cycle.

Jan 1, 1993

By Wright S

Single pellets of mixed lead-zinc concentrate containing up to 20 % lead were roasted in the temperature range of 800-1100¦C. Variables studied included pellet size (from 9-8 to 3-2 mm diameter), gas flowrate past the pellet (from 0.05 to 5 ms t), composition of the atmosphere and the effect of additives such as zinc oxide and silica. After defined periods of time, the pellets were removed from the furnace, quenched and submitted for chemical, XRD, SEM and microprobe analysis. The oxidation of the zinc sulphide followed a shrinking core model. Temperature measurements showed that very high pellet temperatures were experienced at the start of an experiment but after 5-10 minutes these approached a constant temperature. The lead loss from the pellets was then constant with time. Thermodynamics predicted the presence of two bands of lead material in the reacted layer of the pellet. These were found in practice. The lead loss from the pellet occurred from the outer oxysulphate layer via the vaporization of lead oxide polymers. The vapour pressure of PbO, and the loss of lead, was dependent on temperature and bulk gas concentrations of SO2 and 02. At 1100¦C the addition of silica greatly reduced the loss of lead from the pellet. Physical factors such as pellet diameter and gas flowrate past the pellet affected the particle dynamics. These results were found to vary in accordance with the predictions of the Froessling equation.

Jan 1, 1989

By R Bradford, W Gift-Agbey, T Vorster, P Morgan, E Grobler

The Asanko Gold Mine in Ghana started processing ore from the Nkran pit in January 2016 at a production nameplate of 3 Mt/a. The flowsheet is a conventional SAG, ball mill and pebble crusher (SABC) with gravity-gold and carbon-in-leach (CIL) recovery. The nameplate production was comfortably achieved within 3 months, so much so, that it was clear the SABC circuit was capable of processing more than the downstream section of the plant. Consequently, a program of de-bottlenecking was initiated to rectify volumetric capacity constraints. This program was later referred to as ‘Project 5 Million’ (t/a) or P5M. Having completed the de-bottlenecking exercise, it became evident that the SABC circuit could not reach 5 Mt/a solely on hard rock from Nkran. The new challenge was therefore to increase the capacity of the milling circuit through a focused comminution initiative that would address the following: geometallurgical treatment plan; upfront fragmentation requirements; installation of feed and mill monitoring equipment; and integration of a knowledge-based control strategy. This paper takes the reader through the various measures implemented to increase the milling rates and to create a stable/ sustainable control philosophy. As a result of the implementation of advanced mill performance monitoring technology (MillSlicer) and the collaboration between a team of experts in comminution, control and operations, the Asanko Gold Mine process plant feed tonnage has successfully increased from 3 Mt/a to 5 Mt/a.CITATION:Bradford, R, Gift-Agbey, W, Grobler, E, Morgan, P and Vorster, T, 2018. Optimisation of Asanko’s Obotan SABC circuit to achieve ‘Project 5 Million’, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The locality from where these specimens come is distant about 12 miles due south from the township of Bingara New South Wales, and is known locally as Carney's Reef, Barrack's Creek, Top Bingara. The formation traverses the western side of a serpentine spur from the main range, which runs through the country from the other side of Tamworth to Inverell, in the New England District. It has a due north and south trend, with an easterly underlay slightly out of the vertical. The formation has been opened up at different points for a distance of over two miles, and each place showing gold in the stone, and no place more than three to four chlins apart, the whole distance along the line of Reef being leased. The formation varies in thickness, the smallest being about 1 foot and the widest about 10 feet. The following is a list of properties, and description of work done on them at present. First south, and about one and a half miles from Hanion Brothers' old BalIarat claim due north, Court and patty hold a tenacre lease. The formation outcrops near the south boundary, and gold is obtainable in the stone. In the centre of the lease a costeen pit has cut the capping, which shows gold, and about two chains from the north boundary another one cuts the capping, also showing gold. The reef averages, where exposed on this property, 3 feet wide.

East Nelson and Marlborough, in the northeast of the South Island, contain a wide variety of metallic minerals, including gold, silver, copper, chromite, antimony and scheelite, but no sustained metallic mining industry has evolved. Gold was the most sought-after mineral during the first century of European settlement and numerous discoveries were made but these failed to live up to expectations. While traces of gold are widespread in east Nelson, including in quartz veins in Nelson City, no payable deposits were found. In Marlborough the probability of a gold discovery had initially seemed remote but all this changed with the finding of rich deposits in the bed of the Wakamarina River in 1864, which provided a much-needed boost to the provincial economy. However, the decline of gold mining in Marlborough began virtually as soon as it had commenced. Extensive floods in 1865 hastened the exodus of miners to the profitable new fields of the West Coast.

Jan 1, 1993

By R O. James

The usual focus of papers on fatty acid collector action in non-sulfide flotation is on the adsorption of the carboxylate and/or neutral molecule species at the mineral-solution interface. Little attention is paid as to whether or not the solution conditions correspond to true solutions, micellar and other self-assembly objects or precipitates. Our examination of the solution chemistry of the important fatty acid collector, oleic acid, has revealed that many, if not most investigators set their experimental conditions to be in micellar or precipitate domains while arguing, often by implication, that they have only solute species present. We have investigated the equilibrium solution domains usually encountered in studies of oleic acid flotation of such minerals as barite, calcite and fluorite. The alkaline earth-fatty acid and liquid oleic acid precipitate phases exert a strong influence on the solution chemistry, a fact not often appreciated in many studies.

Jan 1, 2005

The timber township of Powelltown, Victoria lies N.E. of Yarra Junction, 60 miles east of Melbourne and in the site of the mill of the Victorian Hardwood Company Proprietary Ltd.A lift gauge railway owned by the company connects Yarra Junction on the Warburton line, with the township through two or three smaller mill centres on the way.The company has been operating for some 12 years. In the divide, about four miles from Powelltown, between the Little Yarra and Latrobe rivers, cutting was continued with material being handled by winch and double incline haulage over the divide. A small bush locomotive dealt with the traffic between the divide and the cutting site.In order to reduce costs, which were heavy at the haulage, the company decided to make a continuous railway from Powelltown to the bush by means of a tunnel through the divide.Hand bore holes were put down on the proposed line of tunnel and showed that the divide at this point consisted of decomposed depth of about 100 ft. towards the eastern or Latrobe side - and that the undecomposed granite summit lay to the west of the surface summit.The bores also served to locate the underground water line, this was afterwards found to rise and fall with wet and weather.To avoid tunnelling in hard and heavy water, the grading of the was laid out with the summit of the hard granite the point in the line.

Jan 1, 1925

By R E. McIvor, K M. Bartholomew

Classification system efficiency (CSE) is a simple, powerful metric that provides a comprehensive measure of classification system performance. CSE directly quantifies the amount of coarse solids in the mill, and as a result, also directly quantifies the percentage of mill power being used effectively. In this manner, it is an effective, practical grinding energy efficiency metric.Three independent variables drive CSE: circulating load ratio, sharpness of classification, and classifier bypass. Due to practical downstream constrains on per cent solids, improvements realised by increasing circulating load reach diminishing returns as sharpness of classification and bypass deteriorate in the most commonly used classification device, the hydrocyclone. This combination of effects leads to the use of CSE, and its relationship to operational economics, as an objective circuit optimisation criterion.Its simplicity in measurement makes CSE a useful tool for the plant metallurgist, and it is not subject to a great amount of experimental error. CSE provides the plant operator a fast, simple, and effective means to evaluate the performance of the plant classification system. Improvements in CSE relate directly to circuit throughput and energy efficiency. This paper, through description and plant case studies demonstrates the power and utility of this emerging grinding system optimisation metric.CITATION:Bartholomew, K M and McIvor, R E, 2013. Classification system efficiency - a comprehensive closed-circuit grinding optimisation metric, in Proceedings World Gold 2013 , pp 389-394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By W J. Shaw

Geometallurgical modelling is now a hot topic in deposit evaluation and in optimising mine performance; however, its history is long and varied. Historically metallurgical sampling has frequently suffered from a lack of data due to the cost of producing representative bulk samples. In the early 1990s geometallurgical modelling similarly suffered from a lack of data due to complex, time consuming and expensive sampling techniques. More recently, simple and relatively cheap tests for geometallurgical variables such as hardness, grindability, throughput, SAG power index, bond work index, crushing index, mineral recovery and concentrate grade have become widespread. The cheaper sampling has resulted in relatively large geometallurgical databases. However, most of the geometallurgical variables sampled are implicitly (and incorrectly) assumed to be additive when modelled by traditional geostatistical techniques, often leading to ill-informed and costly decisions. Geometallurgical variables are mostly non-additive so the current geostatistical challenge is to develop new approaches to dealing with this type of data. This paper briefly describes a historical case study of geometallurgical modelling of the George Fisher Pb-Zn mine completed in the mid 1990s, then outlines some of the current misconceptions of geometallurgical data and modelling techniques regularly applied to it, and finally discusses some recent developments in geometallurgical modelling, with examples from a number of current clients indicating the direction forward.

Jan 1, 2009

A summary of the more important work by previous workers is followed by brief descriptions of the rock formations and regional structure. Type examples of the various forms of mineralization are described and the conclusion is drawn that there has been one main period of ore formation, namely, during the "Viti Revolution" in the mid or late Miocene.INTRODUCTIONThe Crown Colony of Fiji is comprised of a group of some 250 islands situated between latitude 160 sand 21 0 S and longitudes 1770 E and 1780 w: By far the greater, part of the total area, 7,083 sq. miles, is contained within the two main islands, Viti Levu 4,053 sq. miles, and Vanua Levu 2,128 sq. miles, and it is to these that most geologists have directed their studies. The most detailed work has been in the Tavua Basin, north coast of Viti Levu, centering about the mining town of Vatukoula and the geology of this area forms the subject of a separate paper by Blatchford (this volume p. 13).The present contribution summarizes geological knowledge of Fiji, at the time of writing (Feb. 1952), with particular reference to the known mineralIzation, but excluding the Tavua Basin. For general descriptions of Fiji's topography reference should be made to the recent works of Derrick and Dunkin.PREVIOUS WORKERSPeriod 1840-1930Prior to the gold rush of the early 1930s the visiting geologists concerned themselves in the main with the struc...

Jan 1, 1953

By M E. Webb

Safety is a key value in most leading mining companies. Despite years of effort, and significant expense in ‘programs’, operating sites seem to have been left with no real improvement in either the elimination of fatalities or sustained reduction in injuries.Safety systems and processes have grown and evolved, often to the point where they have become overly complicated and marginally useful.MMG Limited, following the consolidation of its Australian operations under a single management structure, undertook a program to effect real and sustained change in its approach to managing safety. The program aimed at improving safety by better engaging its workforce and by making safety processes simple, useful and effective. It defined the role of the supervisor in creating safe work, the role of the people doing work and the role of safe work methods.A safety diagnostic tool was developed to assess site against safety-critical mindsets, behaviours, cultures and systems. The outcome of the diagnostic is considered by the organisation to be the true lead indicator of safety performance.While still a work-in-progress, the program at the Australian Operations of MMG Limited shows that challenging common paradigms in safety management can create real change in safety performance.CITATION:Webb, M E, 2016. Making safety simple, useful and effective, in Proceedings International Mine Management Conference, pp 217-223 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Water is a key resource input to copper heap leach operations in both quality and quantity. A number of recent developments in analysis of the technology have shown that water consumption can be optimised. The leach consumption has been generally considered in terms of minimisation of the evaporative loss by changing the application method (drippers or wobblers). Modelling of the irrigation effects on leach rate has shown that the poorer surface coverage from drippers has an adverse effect on the leach extraction rate. This is particularly evident in the early part of the leach. The use of different irrigation systems during alternate parts of the leach cycle can have benefits in minimising the water consumption without an unacceptable outcome from extended extraction times. By combining the leach rate effect with the evaporative loss estimates, an economic decision matrix can be generated to allow the operator to select an appropriate leach irrigation strategy, combining both irrigation delivery and irrigation rate. In the SX-EW plant, the total quantity of EW bleed and SX scrub stage bleed (both for iron control) can be reduced to an absolute minimum. The economic minimum may be different depending on the cost of producing the high-quality water used to replace the bleed streams. Adjustment of the SX process, in particular use of multiple entrainment control steps, can provide significant reductions in the total bleed and make up requirements.

Jan 1, 2003