Search Documents

At its Port Kembla Plant, Australian Fertilizers Ltd. manufactures Superphosphate and other Phosphatic Fertilizers.Phosphate Rock is received from Nauru and Ocean Island. It contains water insoluble tri-calcium phosphate, Ca3(PO4), to an average of about 86%.It is crushed to pass a 20-mesh x 26-gauge woven wire screen, and is then treated with Sulphuric Acid to give the product Superphosphate with a water solubie prosphate content of 20.5%, estimated as P205. Sulphuric Acid is made by the chamber process. Three sets of chambers are installed, on,e five-chamber set of timber frame work construction and the other two of more recent date, each with four chambers of steel frame work construction. A fourth chamber set is now being built.Sulphuric Acid is delivered for use. at about 70% H2S04, the strength depending upon the rock used.Mixing - The crushed rock and sulphuric acid are mixed in weighed and measured proportions respectiyely in one-ton batches in revolving cast fron pans, mechanically stirred. The mixture, while still slurry, is run into a closed horizontal concrete cylinder (den) where, with the completion of the chemical reaction, it rapidly sets as Superphosphate.Approximately fifty batches are required to fill a den. When full, the den is opened ana the mass cut out by a revolving cutter. The product is elevated and conveyed to any required position in the Superphosphate storage shed, where it dries and matures.Despatch - As required, the Superphosphate is excavated by a two ton grab and conveyed from the matured "dump" to bagging units where it is disintegrated, screened and bagged at twelve bags to the ton. The filled !Jags are closed by machine and delivered to railway trucks immediately.Mixed Fertilizers - Sulphate of Ammonia, Sulphate and Muriate, of Potash, and Blood and Bone are mixed with Superphosphate and thoroughly incorporated to give different mixtures to meet special plant requirements.

Jan 1, 1938

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Sapporo-Iwanai district is located at the intersection of the northeast Japan arc and Kuril arc, associated with the subduction zone. This area is characterized by Miocene submarine volcanism followed by Plio-Pleistocene subaerial volcanism.   Koryu, a small epithermal Au-Ag deposit, occurred in Pleistocene (1.4 - 0.85 Ma) within Miocene sedimentary rocks near a subaerial andesitic volcano, while Toyoha, a large epithermal Pb-Zn-Ag (-Au) deposit, also occurred near a subaerial andesitic volcano. Although most of the base metal deposits formed in middle-late Miocene, Toyoha formed in Plio-Pleistocene (2.93 - 1.60 Ma) within Miocene volcanic and sedimentary rocks. This epithermal mineralization was partly overprinted by xenothermal Cu-Sn-In(-Au) mineralization (2.68 - 0.49 Ma).   Hydrothermal alteration differs vastly between Koryu and Toyoha: host rocks at Koryu were not intensively altered, although wall rocks adjacent to veins were silicified, while those at Toyoha show intensive and extensive neutral-pH alterations. Geological and chronological studies show that middle~late Miocene (12.5 - 8.4 Ma) alteration was pervasive and overprinted by Plio-Pleistocene (2.93 - 0.49 Ma) alteration. The base metal veins in the middle-late Miocene were not well developed, but were large in number with great depth.   These studies show that the hydrothermal activity at Koryu is rather small and short-lived, while that at Toyoha is large, long-lived and characterized by overprinting of different hydrothermal systems. The subaerial magmatic activities yielded not only the andesite lavas, but also generated hydrothermal solutions for the formation of both Koryu and Toyoha. The metals were possibly derived from such magma. At Toyoha, the hydrothermal solutions could also remobilize metals from old ores.   The size, life span of magmatic-hydrothermal system, and overprinting on the old mineralizing systems could constrain the type of metal deposits (precious and polymetallic deposits) nearby subaerial andesitic volcanoes in Plio-Pleistocene.

Jan 1, 2005

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

By Kneisley RO

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north- central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield- pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)- wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By N Robson, E Stephens

Australian mining companies are actively exploring for and developing mineral deposits throughout the world with interests in emerging markets such as Africa, Asia and South America. It is important to understand emerging market risk as this will affect the willingness of mining companies and financial institutions to invest in a country, especially with reference to their key asset, the mining licence or operating/concession agreement. Mining companies looking to develop new projects in emerging markets have different risk profiles than projects in countries such as Australia and Canada. Examples of key risks faced in emerging markets include: political û expropriation, nationalisation, contract frustration, currency inconvertibility, war, terrorism, strikes, riots and civil commotion; and legal û mining legislation, arbitration and dispute resolution, trade agreements. There is a problem in the difference in risk perceptions between mining companies, financial institutions and insurers. This can cause different stakeholders to carry out different evaluations of the risks faced by a project, resulting in confusion about the risk margin attached to any project. In a time where resource nationalisation and energy security are prompting governments to become more involved in the mining sector we run through some recent examples of mining companies that have had problems due to the key risks highlighted earlier. Importance of carrying out the right due diligence to replace perceptions with reality: early identification of risks û detailed due diligence on emerging market risks that may arise will help with their identification and mitigation, make use of companies that can help identify risks and suggest solutions, control the cost of financing û risk margin applied to a project finance loan will be influenced by the risks faced, and risk management and using political risk insurance. There are plenty of opportunities in emerging markets but it is important to recognise the associated risks. Detailed due diligence at an early stage will provide long-term benefits.

Jan 1, 2007

By Y Peng, D J. Bradshaw, G Long

As copper reserves deepen, they are becoming increasingly less pure. Penalty elements such as arsenic, antimony and bismuth are occurring in increasing concentrations. Environmental issues with smelters are leading to increases in penalty rates for these elements such that some concentrates may become difficult to sell. Arsenic concentration in Rosebery copper concentrates during 2010 varied between 3000 and 8500 ppm. Arsenic levels above 5000 ppm can preclude import to some customer countries. Optical mineralogy has indicated that arsenic in Rosebery copper concentrates is most commonly associated with tennantite (Cu12As4S13) in solid solution with tetrahedrite (Cu12As4S13). In addition, silver reports to concentrate as freibergite (Cu12As4S13 ). A reduction in arsenic content will therefore lead to a concurrent reduction in the silver content.A literature review by Long, Peng and Bradshaw (2012) indicated that arsenic bearing minerals could be removed using potential controlled flotation. Some success in reducing the amount of arsenic had also been reported using either roasting or chemical depression using reagents such as lime and cyanide. Due to the location of the Rosebery concentrator adjacent to world heritage listed temperate rainforest, the use of a roaster or cyanide was immediately discounted. Lime is already used as a reagent in the Rosebery flow sheet, so could be considered as a potential arsenic depressant.In order to determine a method of separating out the high arsenic bearing minerals, two series of flotation tests were conducted. The first series investigated the effect of pulp potential on the recovery of copper, silver and arsenic minerals; a second series investigated the effect of pH, froth depth and regrind.CITATION:Long, G, Peng, Y and Bradshaw, D J, 2012. Production of a low arsenic copper concentrate at MMG Rosebery, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 347-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Lethlean

The mining industry in its drive to optimise equipment use and minimise cost simply to remain profitable in an uncertain commodity market needs to develop a greater understanding of equipment capabilities and cost. The factors influencing mobile equipment fleet cost and performance commence at the time of mine planning and continue to exert an influence over the life of the mine. These factors must be understood at the early stages of any operationÆs planning process as they continue to impact both positively and negatively on fleet performance and operating cost throughout the life of the mine. The key factors examined in this paper include: grades; rolling resistance; fragmentation and truck loading.

Jan 1, 1998

By C Yeung, N Swa, D Gribble, R Reupana

BlastLiteÖ is a low density explosive developed by Dyno Nobel and has been in use at BHP Billiton Iron OreÆs Mt Whaleback Operation since March 2004. The Mt Whaleback Operation utilises BlastLite because it offers an attractive alternative to ANFO in soft to medium strength rock types. Its use also reduces the amount of liquid fuel oil consumed and is well aligned with BHP BillitonÆs corporate Energy Excellence initiatives to reduce greenhouse gas emissions. This paper presents the:results of characterisation work completed on-site as a fourth year mining engineering thesis, and application and benefits of the product at Mt Whaleback. One of the key features of low density products is that the detonation is non-ideal. That is, the explosive does not react fully in the detonation driving zone. This manifests itself in that the product is highly dependent on charge diameter and confinement conditions. Dyno Nobel has access to the Vixen suite of detonation codes for characterising the ideal and non-ideal behaviour of explosives. The objectives of this work were to use the Vixen_i code to characterise the detonation performance of BlastLite, in order to understand the role of the bulking agent and to allow modelling of the explosive. The detonation performance was established by detonating a series of unconfined charges at various diameters and measuring the velocity of detonation (VoD). The work program consisted of sourcing and preparing cardboard tubes of various diameters (80 mm to 305 mm). The tubes were loaded with explosive at the BHP Billiton Iron Ore Mt Whaleback test range and detonated one at a time. Over the past three years BlastLite has been used in various applications across the site. Initial findings illustrate that shovel productivity from BlastLite shots was comparable to the baseline ANFO blasts. The study results were also backed with visual inspection and feedback from shovel operators. A work program is currently in place to develop different blends of BlastLite and TITAN« BlastLite to tailor the explosives to various blasting applications. The trials at Mt Whaleback are leading to future opportunities of BHP BillitonÆs satellite orebodies.

Jan 1, 2007

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

By J Vann

Mineral Resource and Ore Reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential pitfalls are to be avoided, however, there are two other requirements which are of equal, if not greater, importance:good communication, and common sense. Estimation of Mineral Resources and particularly of Ore Reserves is almost always a team effort, involving a number of disciplines. Good teamwork requires good communication, both between team members and between the team and other parties having an interest in the process. Breakdown in these lines of communication can have far reaching effects on the project under consideration. The need to use common sense during a Resource or Reserve estimation exercise would seem to be self-evident. It is surprising, however, how often rigid adherence to procedures and methods prevails at the expense of clear thinking, usually with adverse and sometimes fatal effects on the project under consideration. This has become increasingly true as computerised methods have assumed a central role in Resource/Reserve estimation. The critical question that estimators should ask themselves at all stages of the process is: æIs what is being done sensible given the data available, what is known of this deposit and the purpose of the exercise?Æ

Jan 1, 1999

By D A. Williams

The conventional method of transporting mine tailings from a process plant to a tailings storage facility (TSF) is in the form of a low to medium density1 slurry, which can be pumped using centrifugal pumps. Over the past several decades, therefore, mine operators have generally adopted this default approach. There are, however, some convincing arguments why consideration should be given to thickening the tailings slurry to a higher density paste consistency. In particular, the minimisation of environmental impacts, the reduction in water consumption and the cost savings relating to TSF closure make paste an attractive option for the life of mine tailings disposal. There are several environmental impacts that are associated with a conventional slurry TSF, such as land sterilisation, aesthetics, dust, seepage and acid mine drainage. Some of these impacts, such as dusting, may be difficult to mitigate while the TSF is in operation. Others can be influenced by adjustments made to the tailings slurry density at the plant. Unplanned fluctuations in slurry density and/or viscosity can have a significant influence on TSF performance and can exacerbate the environmental impacts relating to the facility. Relatively minor changes in the solids content of the slurry can affect tailings beaching behaviour, degree of segregation, position of the phreatic surface, amount of freeboard, consolidation behaviour, placed (settled) density (and hence TSF capacity) and in situ strength of the tailings. Paste is a non segregating slurry and many of these effects can be minimised at the TSF when the tailings slurry is thickened to a paste. These improvements are manifested by reduced seepage, flexibility in selecting an appropriate final landform, ability to rehabilitate progressively and reductions in plant water usage. It is possible to minimise environmental impacts of a TSF through the use of tailings paste. Ideally the paste production plant should be part of the initial design of the process plant. However, significant benefits can be gained by adding a paste production plant at some time later in the operational life of the mine to reduce environmental impacts and facilitate an environmentally acceptable TSF closure.

Jan 1, 2002

A major new mine to be developed at Pike River during 2005 has been designed to have a minimal impact upon the environment, and an overall net conservation gain. The Pike River Coalfield is located on the West Coast of the South Island of New Zealand on the top of the Paparoa Range approximately 46 km north east of the coastal town of Greymouth. Pike River Coal Company Ltd (PRCC) holds a 40 year mining permit over the coalfield.   In October 2004, the Minister of Conservation granted PRCC access through 1.25 km of Department of Conservation land via an access agreement, and the Environment Court issued a number of consents for the development and operation of the mine, in addition to some existing consents.   The underground mine at Pike River is located under land administered by Department of Conservation, and has been designed to avoid or mitigate adverse environmental effects and integrate into the natural bush surroundings. The mine process has been designed to operate within an environmentally sensitive area and will incorporate technologically advanced methods of mining and processing. The mine process involves hydro mining of the coal, and transportation via a 12 km coal water slurry pipeline, to a dewatering complex located on PRCC land. This will ensure that traffic in the Pike River Catchment up to the mine is minimised.   An extensive series of management plans and monitoring programmes will be used to ensure that the environmental effects of the mine activities are minimised, by evaluating the performance of managerial procedures, and physical mechanisms in place to avoid or mitigate the effects. Trial mining and substance management plans in conjunction with an orthophoto and surface monitoring protocol will ensure that surface features, and water ways are protected from any adverse effects. The Blue Duck enhancement, and pest and predator control programme will help ensure that an overall net conservation gain is achieved.   Developing transparent working relationships and good communication with Department of Conservation, Iwi (Ngati Waewae and Ngai Tahu), and local environment groups has been and remains very important in the development of this project.

Jan 1, 2005

The story of the rise, progress, and development of our modern railway system is a long but an exceedingly interesting one. The phases it has passed through, the discussions that have arisen from time to time on the most economic modes of construction and working, and the final result these various discussions have led to, are full of importance and interest to the engineer. It is not my intention to deal historically with the subject. I desire simply to speak to the requirements of the hour in Australia. It will not be disputed, I think, that these colonies have reached a point in railway construction and management when, if additional lines to any extent are still to be built, a different principle must be adopted. There are yet large tracts and areas of country to be tapped by the rail and the locomotive, which for years to come must remain untouched if the same expensive gauges and modes of construction are continued. We have yet to see clearly the necessity of introducing a system of light lines that will pay their own way and at the same time augment the traffic of our main lines. This question really no longer remains an unsolved problem. It lies, in a few words, in the acceptance of the, narrowest gauge and the simplest mode of construction that can constitute a pacticable railway. I fear it is hopeless to suggest that private companies should be legally permitted to construct such lines. It seems as if it were next to impossible to move official authorities to enter upon the construction of lines on this principle. It is, all the same an undoubted fact that if private companies could obtain Acts of Parliament, that in several of the colonies a new impetus would be given to railway construction.I may point out that not only has the principle of narrow gauge light railways been adopted in India but private companies are obtaining power to build them. Outside of :England many narrow gauge lines have been made, and in France, Denmark, Italy, and Sweden they have been highly successful.

By A Baensch, E Grimsley

Eloise Copper Mine is situated 56 km east-southeast of Cloncurry, Queensland, Australia. The deposit was discovered by BHP Minerals in 1986 during follow up diamond drilling of EM anomalies associated with major aeromagnetic anomalies. The deposit is overlain by 60 m of Mesozoic cover. Amalg Resources NL commenced mining during 1995 by means of decline access and long hole-stoping. The total mineral resource comprised 1.77 million tonnes at 4.10 per cent Cu as at the end of June 2003. Proved and probable reserves are 930 000 tonnes at 3.97 per cent Cu. Mineralisation is hosted within a strongly foliated Proterozoic meta-sedimentary sequence comprising arenites and schists. The metasediment sequence also contains a coarse-grained amphibolite body possibly representing an early intrusion of gabbroic composition. Economic mineralisation characteristically occurs as a number of steeply plunging lenticular bodies with strike lengths of between 100 and 200 m and maximum widths approaching 25 m. The principal orebody, the Levuka (B) Lode, displays a down plunge extension exceeding 1000 m and is open at depth. Ore mineralogy is almost exclusively chalcopyrite with the principal gangue phases consisting of pyrrhotite + quartz + carbonate. A biotite + hornblende + magnetite assemblage represents locally intense mafic alteration of the metasedimentary host sequence. Magnetite is present in variable amounts and may be locally significant in some of the smaller satellite orebodies. Within the orebodies the sulfides display a range of textures from massive through to vein like. Sulfides commonly display brecciated textures at a range of scales. Post-mineralisation faulting has severely dislocated the orebodies, resulting in a complex arrangement of fault bounded ore blocks. These faults display considerable variability in regard to strike, dip and amount and direction of throw. A recent review of the fault system by means of large-scale structure underground mapping, re-interpretation of drill core and 3D modelling has led to a significant improvement in the understanding of these structures. A significant upgrade of the geological database has accompanied the structural review. The overall improved understanding has aided the mine design processes with particular regard to decline and access development and pillar location. This has also impacted on the design of drilling programs and exploration for additional satellite ore zones.

Jan 1, 2003

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

Interpreted geologic domains provide the geologic architecture of many current models used to estimate the potential economic resources in mineral deposits. The spatial extent of each domain is usually defined by a three-dimensional wireframe or triangulated surface.The set of geologic wireframes forming part of a resource model might generally be called a spatial interpretation of some set of geologic features coincident with the mineralisation, based primarily on logged and mapped properties of the samples and other exposures of the mineralisation. The interpreted spatial distribution of rock type, alteration and grade of drill hole samples above a particular grade threshold are commonly used criteria in constructing the geologic domain wireframes. Frequently, the grade threshold is closely related to the anticipated economic cut-off grade. The boundaries or spatial limits of different domains are most commonly defined as æhardÆ or æsoftÆ. A æhardÆ boundary usually means no dependent relationship of any kind is defined between the properties of samples inside a particular domain wireframe and those samples outside the wireframe. A æsoftÆ boundary commonly implies that some kind of dependent relationship does prevail between the properties of samples inside and outside the particular wireframe. Many ways are used to describe those relationships, few of which are based on spatial analysis of the continuity of sample attributes across the domain boundaries. In local estimation procedures such as ordinary block kriging, æhardÆ boundaries act as a total barrier to the influence of samples on either side of the boundary depending on the location of the block being estimated. In some instances, æsemi-permeableÆ boundaries are used in which the samples inside a domain wireframe are allowed to influence the estimates outside but not the reverse. This can lead to many undesirable effects in estimates of block grades.This paper discusses the value of this approach to geologic domaining from a viewpoint of model complexity, as well as in relation to the implications for both linear and non-linear estimation methods and contrasts it with alternatives. It also explores some important consequences of using æhardÆ and æsoftÆ geological boundaries with the commonly used modelling methods: excessive smoothing of estimates near domain boundaries and conditionally biased estimates of grade at the global and local scale.

Sep 26, 2011

Paddington processing plant is located approximately 30 km north of Kalgoorlie on the Menzies Highway and is owned by Placer Dome Asia Pacific. First mining was from the Paddington Pit, but in subsequent years the plant has had a history of treating ores from a large number of sources, and has used several different methods to reconcile mining and mill production. Reconciliations are necessary to keep a check on the quality control of mining and grade control processÆs. There is a need to be able to identify and resolve issues that will affect the profitability of the organisation quickly. They are also used to check the quality of the resource/reserve statements, and allow the accurate and timely payment of royalties to stakeholders. During the formation of the Kalgoorlie West operations when Delta Gold Limited and Goldfields Limited merged in 2001, the complexity of reconciliations increased dramatically. The expansion of the scope of reconciliations to include two mills, four underground mines and seven open pits, and ore from one deposit to both mills meant that a revised strategy was essential. A variety of issues have arisen over the years with discrepancies occurring when reconciling both tonnes and grade. There are many ways to approach reconciliations, and in recent times these philosophies have been widely debated on site. A consistent and logical approach that takes into account many different sources of ore, as well as different methods of delivery to the Run of Mine stockpiles is therefore necessary. This would standardise the different approaches taken by the various operations that combined to form Kalgoorlie west. The new method reconciles mill production back to the individual ore sources, and produces reconciled-mined tonnes and grade based on the mill throughput and the change in stockpiles. There will generally be a small discrepancy between the claimed mined tonnes produced (and grades) and the mill production. This needs to be highlighted to the operations concerned if it considered unacceptably large. Paddington mill over the last few years has had up to ten sources of ore each year, and up to 15 different stockpiles being processed during each month from those various pits. This combined with the need for a blended oxide/fresh feed, whilst striving to deliver a consistent (grade and hardness) product to the mill, has meant that reconciliations have been very difficult.

Jan 1, 2003