Search Documents

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Recent data contributions to New Zealand Mesozoic terrane geology confirm the consensus interpretation thatNew Zealand grew by the progressive addition of material by plutonic and accretionary processes along the Gondwana margin. The data also: 1. emphasise the discontinuous but inter-related nature of these processes of continental growth, 2. better establish a direct Gondwana correlation of the Western Province and probable Gondwana provenance of at least some of the Eastern Province, 3. suggest specific times and places when passive or strike-slip rather than subduction regimes are recorded along the south Gondwana margin, and 4. potentially lead to interpretations emphasising parautochthonous rather than far travelled relationships between many New Zealand terranes.  

Jan 1, 1995

Exploration for uranium in Australia has so far discovered reserves equal to 17.5% of the Western World's. The Australian uranium industry, when fully developed, will be one of the largest producers and possibly the largest exporter in the world. The world's nuclear industry is young, rapidly developing in size and technology and is subject to more social, political and regulatory controls than any other industry. This paper considers the probable development of Australia's uranium industry against a background of normal commercial parameters together with other factors which are peculiar to the nuclear industry. As the theme of this conference is "Australia's role in the World Mineral Indus- try" this paper concentrates on the commercial and practical aspects associated with the development of Australia's uranium resources in a world context.

Jan 1, 1979

The oxidation of sulphide minerals in aqueous suspension is discussed from several viewpoints. Limitations of our present knowledge are pointed out, and several points where further information would be of special interest are mentioned.Firstly, some properties of minerals and their effect on oxidation are discussed. Properties of different species, such as crystal structure, lattice bonding, and "metallic" properties are mentioned, and then the effect of variation within a given species is discussed. The effect of physical factors, especially particle size, is also considered. Other variables discussed include the importance of solution composition, and its effect on the nature and rate of reaction, and the use of various oxidising agents. Some factors concerned with the whole system, such as temperature, pulp density and stirring rate are then considered.Finally, the nature of various oxidation products is discussed with reference to the kinetics of reaction and the nature of the rate limiting step. It is suggested that more attention should be paid to electrochemical explanations of the reaction mechanism.INTRODUCTIONKnowledge of the factors governing the rate of oxidation of sulphide minerals in aqueous suspension is a prerequisite for the effective control of many ore treatment operations. Rapid oxidation of sulphides is usually desired during the leaching of sulphide ores and concentrates, but in the cyanidation of gold ores, or in the leaching of uranium ores, any oxidation of sulphides may be regarded as an undesirable side reaction. Knowledge of many of the factors involved is also of interest in connection with the oxidation of sulphides in flotation circuits and in natural ore forming processes.Systems for which some reasonably quantitative data have been published are listed in Table 1. Qualitative...

Jan 1, 1961

By E Werner, J J. Donovan, A J. Morris

Coal mining in the Pittsburgh coal seam, in the eastern United States, began in the late-1700s. Since that time numerous mining technologies have been used throughout the basin. Environmental concerns, particularly mine discharge quality, have only been considered since the early-1970s. During the last 20 years, many of the larger underground mines have closed and are now either flooding or already flooded. In order to understand the consequences and potential future effects of this flooding, mine mapping of the basin has been compiled utilising a geographic information system (GIS) with an emphasis on locating barrier pillars between mines. Mine flooding has been monitored at numerous sites utilising pressure transducers and data loggers. These data have been combined with historical data from mining companies and structure contour maps to yield chronological flooding maps of the basin from 1980 to present. Utilising these maps and the indicated flooding rates, future discharge locations have been identified along with estimates of when these discharges are likely to occur. Related work has identified barrier pillar hydraulic conductivities and vertical infiltration rates as a function of overburden thickness. All of this information has been integrated into a groundwater flow model that simulates mine flooding. This model is useful in defining mine to mine interactions as the various mines fill with water, and the testing of various flooding scenarios. The model will be used in evaluating mine discharge rates and evaluating the options for regional mine drainage treatment.

Jan 1, 2003

IN a mine with any considerable output the economical handling and transport of ore underground is a matter of prime importance, and in the design or lay-out of a trucking system the question of what form the points and crossings are to take should be one of the first considered. Trucks may be moved from one line of rails to another by the following means: by flat sheets, with which may be coupled turn-tables, or by points and crossings. The latter class may be further divided into fixed and movable points.Flat sheets and turn-tables, owing to the time and skill needed by the trucker in using them, are seldom of great value with large tonnages, unless for purely temporary work, and the choice narrows down to one between fixed and movable points andcrossings. Both systems have their disadvantages - movable points being liable to jamb with dirt and get out of order, whilst with fixed points trucks may sometimes run over the points and capsize, or go on to the wrong line, though this is not of frequent occurrence. On the other hand. the fixed points are simple, easily laid, and strong, and there is no necessity for the trucker to work any levers, the truck being guided on to its new direction by screwing.Cast-iron points and crossings were first introduced into the North mine during the opening-up of the 950-ft. level, and the first arrangement was designed for a double turn-out in the main crosscut. Since then both the points and crossings have beenmodified several times, and it may be interesting to briefly outline the various forms through which they have passed, showing the reasons for the retention of some features and the rejection of others.

Jan 1, 1915

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

By Y Ren

The algorithms employed by the commercial tools are either heuristic algorithm or iterative optimisation of a subsystem. This often results in a suboptimal schedule. In this paper, the author presents a new scheduling algorithm that incorporates with a novel stockpile configuration system, an improved algorithm on multiple processes and a mixed-integer linear programming (MILP) global optimisation model. It can simultaneously optimise stockpiles, blending, multiple processes as well as multiple mines. In addition, it allows the user to interact with the solution to adjust the solution to be practical and desirable.CITATION:Ren, Y, 2013. A simultaneous optimisation tool for open pit mine scheduling, in Proceedings World Gold 2013 , pp 427-432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M Haydon

How do you portray a large structurally and stratigraphically complex deposit to return a meaningful resource estimation, and produce a geological model that is useable for planning on a daily basis? The George Fisher Mine is located 22 km north of Mount Isa and forms part of XstrataÆs Zinc Group operations. It is currently a major producer of zinc, lead and silver in the region with an estimated total resource for all categories of 127 Mt at 100g/t Ag, 5.3 per cent Pb and 9.2 per cent Zn (June 2005). Production in 2005 totalled 2 647 492 wet tonnes for 317 699 kg Ag, 140 317 tonnes Pb and 230 331 tonnes Zn from underground operations. George Fisher (GF) consists of two deposits that are structurally complex on a mine scale, George Fisher North (GFN) and George Fisher South (GFS). Regional faulting has resulted in a 2 km long package of variably pyritic shale and siltstone that separates the deposits. This paper looks specifically at GFN. Distinct correlations exist between the two deposits based on stratigraphic matches; however, orebody characteristics, geometry and fault architectures differ significantly between the two. The deposits consist of multiple, sedimentary-hosted, stratiform orebodies from 2 to 25 m wide, separated by waste intervals of variable width. Each ore-waste interval is modelled as an individual geological domain. Structurally, George Fisher North (GFN) contains a series of major late-stage NE faults with dextral offset(s) of up to 130 m. Further complexity is added by NS, NW and NNE striking fault orientations that can produce either a loss or repeat of stratigraphy, local drag folding, orebody attenuation and block rotation. Due to this structural complexity and orebody offsets, domains at GFN are further divided into fault blocks (FB). The GFN model comprises eight FBs over a strike length of 1 km, all of which are modelled independently. As drilling progresses and additional resources are converted, further FBs will be added at major fault offsets to accommodate orebody and model expansion. This will be in addition to what is already a large and time-consuming data set to manage and update. For example, each FB has 18 domains each with two constraining wireframes (hanging wall and footwall). Each wireframe has several sets of point data depending on the type of data available, ie diamond drilling, mapping or interpretation points. This equates to over 1100 separate files to manage. Additional wireframes and files are also required for major structures, daily planning requirements and block model runs. In total some 1500 files are managed, updated and maintained for GFN alone. The ongoing need to expand as a business and optimise production in the current economic climate where there is a global demand for metal has led to an increase in production at GF. This has resulted in a rapidly growing data set and highlights the importance of practical and efficient modelling to achieve a meaningful resource estimate. This paper focuses on the geological modelling, modelling approaches and techniques employed for the GFN deposit.

Jan 1, 2006

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

The use of scrapers in mining and earthmoving operations is not new, in fact they are one of the earliest methods of bulk earthmoving. A single machine which can load, haul, and dump material with a minimum of ancilliary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancilliary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

By D Elder, S Bell

Over the last five years Solid Energy New Zealand (SENZ) has gone through a series of changes in response to both external and internal factors. These changes have included corporate reorganisation and funding restructure, as well as modifications to medium and long term business objectives. The nature and size of its coal reserves and markets requires SENZ to continue developing new mines as existing mines are depleted. As well, there are opportunities to develop new mines as coal markets change or to realise value from existing coal resources. To assist in this process, a set of mine project assessment guidelines which are relevant to the size and scale of anticipated mine developments have been developed for SENZ. These project guidelines are structured to operate from the early stages of project or resource review through to final feasibility study stage. The guidelines provide both a basis for planning and budgeting, and a control mechanism within the company. They also enable clear understanding of the status of individual projects and provide a framework for comparison between projects. SENZ now has a defined method to plan, monitor and control this important aspect of its business. The paper explains the development and structure of the guidelines, as well as providing examples of their application. and use. It demonstrates how SENZ integrates its long term planning, five year planning, annual planning, project planning and risk management to maximise the value of individual projects, business units and the company overall in a consistent manner.

Jan 1, 2002

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Rope guides, consisting of ropes spanning between anchor points at the top and bottom of shafts, have frequently been considered as a viable alternative to fixed guides, comprising buntons and guides. However, their design has generally been based on empirically derived rules, arising from European hoisting practice of 50 to 100 years ago. This paper describes a recent technology development project aimed at defining and quantifying the important forces acting on rope guided conveyances, calculating the resulting displacement of the conveyances and assessing whether the displacements are acceptable or not. The paper describes the derivation of aerodynamic force coefficients based on CFD analyses and other significant forces acting on the conveyance and rope system. The conveyance displacements may be calculated using computer simulation of the mechanical system, or approximately using simplified equations given in the paper. Measurements taken to confirm the suitability of the proposed formulation are described. The combination of displacements and assessment of the rope guide system design are proposed, based on the ratio of design clearances and the predicted displacements.

Jan 1, 2005

By C Jia, J Graindorge, L M. Olssen

Picking up abandoned mining tenements and looking to recover remnant resources around old operations is an opportunity that comes with its own challenges and risks. Reliance on information released to government departments (such as the Department of Mines and Petroleum (DMP) in Western Australia) by the previous owners, can compound the risk.This paper explores Alto Metals Ltd’s Lord Nelson and Lord Henry deposits and surrounds near the town of Sandstone in Western Australia. The Lord Nelson and Lord Henry open pits produced around 2 Mt of ore for over 250 koz of gold during production between 1999 and 2010. There has been no further work carried out in the area between 2010 and 2016. The deposits are open at depth and along strike.Alto Metals picked up the tenements in 2016 and has subsequently re-estimated remnant resources around Lord Nelson and Lord Henry, and publicly reported updated Mineral Resources in accordance with the JORC Code 2012.All of the information was manually compiled from data released to the DMP and annual reports. This paper highlights the challenges and risks arising from this data compilation, geological interpretation, re-estimation and classification process, together with future opportunities and challenges for further developing the area.CITATION:Olssen, L M, Graindorge, J and Jia, C, 2017. Starting from scratch – defining remnant resources from publicly available data: a case study from the Lord Nelson and Lord Henry gold deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 175–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S Raval

The estimation of greenhouse gas emissions from coalmines is increasingly becoming a priority for both operators and regulators. At the same time, involved scientific challenges in the methane measurements is generating significant interest from global research community. Various technology providers are also actively engaged in improving their sensors and platforms to address the measurement challenges and capitalise the market opportunities. This presentation highlights rapidly evolving multifaceted landscape of coalmine greenhouse gas emissions. It covers the advances in sensors for the detections, including ground-based, airborne, and satellite-based systems as well as models for the emission estimations, including attempts to reduce the involved uncertainties.

Sep 1, 2024

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By J Canterford

Although we have access to a wide range of sophisticated process design and improvement tools in combination with a significant range of case studies, the mineral resource industry still manages to be plagued by the negative publicity surrounding operating plant failures because they were neither smart nor safe, together with proposed projects that fail at the first or second hurdle. The general public and the finance industry are generally totally uniformed about projects that ramp-up to name plate capacity on time and on budget and even more so when ahead of schedule and under budget. As the saying goes, good news does not cut the mustard.The following is a summary of the author’s sometimes jaundiced view about why metallurgical plants do not live up to their technical and commercial expectations. In no way should the summary be construed as a negative reflection on the skills of the metallurgical profession. Rather, it is to be taken as a positive acknowledgement of those skills and is intended to highlight some of the major considerations that need to be assessed as a potential project transforms into a sustainable technical and commercial reality.While a considerable portion of the summary is directed at developing hydrometallurgical flowsheets, the general principles are equally important to all aspects of extractive metallurgy.For convenience, the summary covers the following five basic discussion points – project, people, process, patents and politicians.

Aug 8, 2011