Search Documents

The medical evaluation of the health effects of dust exposure in the mining industry should be based on the premise that the results of the medical examinations will be considered in relation to the previous history of exposure to dust.(l) To this end the Mines Regulation Act and the Regulations under that Act in West- ern Australia provide for: the prime responsibility for dust sampling to rest with the mining companies; the appointment of a Ventilation officer by each mine and the sampling and record- ing by him of dust and toxic gases in work places at three monthly intervals, or more frequently as required; the appointment of a Mines Medical Officer who shall make provision for the medical examination of persons and the prevention of occupational diseases; the appointment of a Ventilation Board, consisting of the State Mining Engineer, the Senior Inspector of Mines for the State, an Inspector of Mines having specialised training in ventilation tech- nology, a medical practitioner having specialised experience in occupational health problems relevant to the mining industry, and a Scientific Officer having duties under the provisions of the Clean Air Act, 1964;

Jan 1, 1979

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The discovery of copper and nickel sulphides in the Riwaka Complex in 1967 led to considerable exploration activity by a number of companies. Various exploration techniques used by these companies are summarised and discussed. Activity of these companies shows that mineralisation is mainly confined to the southern, ultramafic section of the Riwaka Complex where geological mapping recognised sixteen units within, or associated with the Riwaka Complex. Significant pyrrhotite, pentlandite chalcopyrite mineralisation is restricted to biotite feldspar pyroxenites and to clinopyroxenite units. Lesser and more erratically distributed pyrite chalcopyrite pyrrhotite mineralisation occurs in poikilitic pyroxene hornblendites, melanocratic gabbros, and in marginal diorite lenses. It is suggested that a linear belt of layered ultramafic and mafic rocks described in Fiordland by Williams (1974) may be a southern extension of the Riwaka Complex. The Riwaka Complex has been classified as belonging to the Picritic subtype, (Tholeiitic suite), of Naldrett and Cabri, (1976), and as such it is concluded that it exhibits substantial potential for the discovery of economic copper and nickel deposits. It is considered that the complex is a multiphase differentiated intrusion emplaced in a major tensional fracture zone that developed in a relatively stable tectonic environment, namely a succession of middle Paleozoic shallow water shelf sediments. Based on sparse available evidence it is suggested that the Riwaka Complex was intruded in the lower to middle Permian. It is further suggested that the tensional fracturing was initiated by the onset of subduction process which were responsible for the development of the Permian volcanic arcs and ophiolite belt in the north west Nelson area.

Jan 1, 1977

By J Mauk

Water-rock reactions such as pyrite oxidation and calcite dissolution strongly influence the pH of pit lakes that develop in open-cast mines after mine closure. The Martha Mine, located in world-class epithermal Au-Ag deposit at the southern end of the Coromandel Peninsula, New Zealand, is scheduled to close in 2007, after which the pit excavation will be rehabilitated into a recreational lake; the first pit lake in New Zealand. Mineral distribution maps from XRD results of 130 andesite samples identify regions that could produce or consume acidity in the future pit lake. Maps show pyrite, calcite, adularia, albite, illite and chlorite distribution in the wall rocks. These data identify five alteration mineral associations: potassic, propylitic, weathered, oxidised and weakly-altered. Pyrite occurs in potassic, propylitic and weathered associations, whereas calcite is restricted to propylitic association in the northeast wall. Subaerial, epilimnion, and hypolimnion exposure zones describe the physical and chemical weathering processes that are likely to occur in regions of pit wall, and the potential effects on lake water chemistry. The pH of epilimnion water will depend on the relative abundance of pyrite and calcite in the propylitic association in the northeast wall, whereas hypolimnion pH will depend upon the frequency of whole-lake circulation events that distribute dissolved oxygen to deep lake layer. In mines with diverse alteration associations, mineral distribution maps are an essential precursor for accurately estimating water-rock reactions in pit lake environments. Data may be directly incorporated into a quantitative geochemical model of future pit lake water chemistry.

Jan 1, 2002

By H Utama, R Heryadi

The demand for environmentally friendly commercial explosives has increased globally due to concerns regarding environmentally friendly mining activities. Ammonium nitrate fuel oil (ANFO) and bulk emulsion explosives (BEE) are two kinds of civil explosives primarily used in coal and mineral mining in Indonesia. Indonesia is one of the leading countries in coal and mineral mining production and export, with abundant resources; therefore, the consumption of civil explosives such as ANFO and BEE is enormous. The selection and evaluation of commercial explosives are mostly done on the commercial and technical side, and no assessment is made based on environmental aspects. This preliminary study evaluates the economic value and environmental burden of greenhouse gas emissions produced by ANFO and BEE and determines which type of explosives is more environmentally friendly. The combination of environmental and economic indicators, eco-efficiency (E/E), was selected to investigate BEE’s economic and environmental performance compared to ANFO. The life cycle of greenhouse gas emissions of BEE and AN was determined using previously available studies and simple calculations. The cost of the product or explosives was used to represent the economic value. The E/E results showed that environmental and economic sustainability could be enhanced using BEE.

Sep 1, 2024

Saxonvale mine is a multi bench open pit coal mine developed to its Stage I capacity of 1.75 Mt/y of run of mine coal. Detailed engineering studies for the mine commenced in April 1980, approval to proceed with the development was received in July 1980 and first coal shipments were made in April 1982. The engineering and project management of the mine development was carried out by BHP Engineering. This paper outlines the design and site administration for the development and describes both the organisation structure and the control and administration procedures used by BHP Engineering to ensure that the project was Successful.

Jan 1, 1983

Large GDP increases in the Pacific Rim countries have been accompanied by similarly large increases in demand for oil products. In the case of residual fuels, this demand has been tempered by the substitution of other energy products such as coal or gas.In the region's developing and newly industrialised nations, it has not been possible to make the very large investements in infrastructure which allow other energy sources to be used for transportation. As a result, GDP growth has been mirrored in the demand growth for automotive fuels. Other non-sustitutable products such as lubricants have also benefitted by the region's GDP growth.The combination of a number of years of sustained growth, coupled with increasing quality requirements is now stretching the upgrading capacity of the region's refineries. If, as seems likely, the region continues to enjoy a high GDP growth rate, then this will be accompanied by increasing reliance on finished products coming out of the Middle East. The owners of the most simple form of refinery in which crude is simply distilled and the naphtha reformed into petrol will face major capital investments. If they decide not to bear this cost, they will face increasing problems in selling their surplus residual fuel oil at an economic price. Quality will become an increasingly important issue. Not only in the well publicised areas such as unleaded petrol, but also for products such as lubricants which play a major role in the efficiency of modem equipment. Quality of service such as hours of opening, ease of access, and service station facilities will also become increasingly important as the oil companies use these to attract customers and gain brand differentiation.

Jan 1, 1990

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010

To carry out its responsibilities the SECV needs to manage the visual environment effectively. Every land oriented decision effects what we see and the value in pursuing visual excellence is supported by informed opinion, widespread community interest and evidence of cost- effectiveness.By knowing how we perceive the landscape and then changing or conserving it we can assist in fostering a positive mental image of a countyside which is welcomed by the local and regional community.It is useful to examine key design elements and the value we place on visual impressions in relation to three significant SECV rehabilitation projects, at Loy Yang, Newport and Morwell Open Cut.

Jan 1, 1992

By A Nisbett

The largest single operating loss in many hydrometallurgical plants is the poor recovery of leached product in the solids sent to tailings. Any reduction in the concentration of the valuable species in this stream will improve the project economics. Conventional design, to reduce the soluble loss, is to increase the number of wash stages or the wash/water ratio. This approach is limited in effectiveness as it can only reduce the soluble loss to that dictated by the concentration in the returning solution. For copper plants this concentration is set by the recovery in the solvent extraction (SX) plant. When using a single grade of SX feed a single grade of SX raffinate is produced generally with five to seven per cent of the copper still remaining in solution. An alternative approach has been developed by Cognis Corporation and implemented on a number of recent projects using engineering input from Miller Metallurgical Services. The SX plant feed is æsplitÆ into two different streams: a high-grade stream containing up to 75 per cent of the copper and a low-grade stream with the remaining copper. This Split-CircuitÖ concept has significant benefits in terms of both copper recovery and reduction in acid costs. The high-grade stream has the bulk of the copper removed and the raffinate sent directly back to the leach; to fully re-use the acid that has been generated during extraction in the SX process. The recycling of this higher concentrated acid stream considerably reduces the acid in the raffinate sent to washing steps. It represents a significant saving in acid consumed via the tails stream. The low-grade stream has a significantly lower SX feed grade and hence produces a lower raffinate acid and copper concentration. This lowers the economic species in the wash solution and hence reduces the soluble loss accordingly. Other operating improvements are realised with lower neutralisation costs (with the lower acid in the wash stream) and from a decreased need for in-circuit neutralisation to improve SX performance. The SX plant itself is also split into a high-grade extraction and a low-grade extraction stream to enable the low-grade raffinate to be produced. A number of circuit alternatives have been utilised that have provided a range of benefits. The circuit concept has been included into both new and existing plant operation. As a result of this experience other methods of incorporating the concept into a circuit have been developed.

Jan 1, 2005

By C Xuan, J H. Park, Q Wang, C Shen, D Kumar, W Mu

Dissolution of non-metallic inclusions in the metallurgical slag is of vital importance for cleanliness control of the steel manufacturing. With the development of high temperature confocal laser scanning microscope (HT-CLSM), new insights have been obtained due to its in situ observation characteristics, higher resolution and precise control. However, HT-CLSM measurement has the limitation, eg the slag composition cannot include high amount of transition metal oxides. In addition, it is time consuming for the experimental procedure and not so simple to succeed for every measurement. It is known that digitalisation has made a significant progress in recent years. Machine learning (ML), a sub-domain of artificial intelligence (AI), is the key enabling technology for the digitalisation of the material science and industry. The database for ML model is collected using almost all available HT-CLSM experimental data and subsequently the established database is trained by different ML methods. Unseen data is used as the benchmark of the ML model. Al2O3 dissolution is the main process to be predicted in the current study. A good agreement between the HT-CLSM data and the ML model prediction results show the possibility to apply ML in process metallurgy.

Jun 19, 2024

By J J. Hanhiniemi, M S. Powell

A ‘Variable Blend and Rates’ model is developed for SAG mills which extends upon the JKSimMet® Variable Rates Model. Similarly, a ‘Variable Blend Residence Constrained Perfect Mixing’ Ball Mill model is also introduced, also extending upon the existing JKSimMet® model. These models are used in conjunction with JKSimMet® while employing external technical programs. The technical model is then used to inform an economic model described elsewhere in Hanhiniemi and Powell (2022), which calculate operating and unit costs based on operating conditions, design, and ore characterisation. The SAG and ball mill models include constraints beyond those in the JKSimMet® models. The SAG model constraints include Size Specific Energy (SSE) verification, charge weight limit, and assessment of the impact of media to ore composition in the charge using the SAG Charge SSE Model developed in this paper. The ball mill model includes residence time, volumetric capacity, and SSE verification constraints. These models are applied to Cortez Gold Mine in the processing of two very different ore types and their blends; ‘Horse Canyon’ which is softer in coarser sizes and competent is fine sizes, and ‘Wenban’ which is competent at coarser sizes but softer in fine sizes than Horse Canyon. Horse Canyon also has a finer run-of-mine size distribution then Wenban. The application of the model at this site included undertaking five surveys at varying blends. The behaviours of the blends and individual components is then studied in the SABC circuit. A nonlinearity is observed with throughputs increasing with blending. The newly developed modelling approach captures these responses. Controlled blending based on ore competence-by-size and size distribution was implemented by the site, which then realised significant improvements in throughput without any capital cost (Ntiamoah et al, 2020). The modelling developed in this paper is then compared to existing practice, and the new method was found to provide improved fidelity and utility. A three-dimensional surface is then developed using the model describing the SAG mill throughput capacity at varying conditions (speed-filling) versus varying blend. The change in throughput as a function of only the changing charge composition is presented. The result is nonlinear, and explanations are provided to describe this behaviour.

Aug 24, 2022

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

By Montini A

The dynamic behaviour of the load in a pilot-scale ball mill has been measured as a function of axial position within the mill, end plate lifter design, load volume J (percent of mill volume), percent solids in the slurry S and mill speed N (percent of critical speed). Conductivity probes were inserted through the shell of the mill to provide online measurements of the dynamic orientation of the load in the mill. It was found that 1. the height of the shoulder of the load is increased by increasing J, S or N. 2. Measurements of the effect of S on the location of the shoulder of the load should be very useful in mill control strategies. 3. The axial centre of gravity of the load in the mill is not affected by operating conditions. 4. The presence of lifters on the feed end plate does not affect the torque drawn by the mill. 5. Holdup of slurry in the mill is a strong function of slurry viscosity and a weak function of mill speed.

Jan 1, 1986

By Opitz E. A

The integration of environmental and permitting strategies into development has become a routine part of doing business for the international minerals industry. Paralleling the development schedule with the environmental and permitting schedule is critical to ensuring that design recognises environmental constraints and that the environmental and permitting program has the right focus and achieves the objective of obtaining workable permits that reflect the project design. Regulatory issues including the law of and controls established by the country the project is situated in, the requirements of international financing institutions, international politics and the role of environmental groups and the particular precedents and processes established are all important issues that must be recognised and incorporated into the permitting program by the developer. Technical issues including collecting early environmental data during exploration, establishing hydro-meteorology equipment, baseline data gathering, and getting good environmental engineering information as a part of feasibility and design are also critical issues to the success of a project which are under the direct control of the developer. Finally tying all of these issues into a single integrated strategy under the direction and control of a nominated team is necessary to maintain focus and achieve results.

Jan 1, 1997

By P Hofmeyr, D Pretorius

Iron ore, which is transported by rail from the iron ore mines at Sishen in the Northern Cape, to the Saldanha Iron Ore Terminal in the Western Cape, needs to be analysed while loading to be exported. Every shipment will be sampled and an average analysis of the ore will be produced which is required by the purchaser at the receiving port. On arrival at the iron ore terminal at Saldanha, the ore is tipped from the rail trucks onto conveyor belts to be either stockpiled or direct-loaded. The conveyor belts run under the sampling plant and the ore is sampled periodically by means of an automated cross-belt sampler. This is the first iron ore port sampling facility in which the automated sampler is situated above the conveyor belts and not adjacent to them. A portion of the primary sample taken off the belt is moved to the dedicated sampling laboratory situated behind the cross-belt sampler and over the conveyor belt lines. The sample is split in the laboratory, one split being used for moisture and particle size determination and the other part is dried and then analysed by means of X-ray fluorescence spectrometry (XRFS) on fusion beads for major and minor elements. Particular care is taken to obtain high quality data for penalty elements.This sampling plant is completely automated and from the primary cross-belt sampler to final analysis by XRFS no manual steps are involved. This has meant that some processes are used which are suitable for automation and are ISO compliant but not necessarily ISO-certificated. The ISO manuals were developed with manual laboratory processes in mind. Precautions are also taken to maintain the integrity and representativity of the samples. This paper is a case study?describing?the automated sampling systems used at the Saldanha Iron Ore Terminal sampling facility and laboratory from conveyor belt to analysis.CITATION:Hofmeyr, P and Pretorius, D, 2012. Automated sampling of iron ore for analysis at the Saldanha Iron Ore Terminal in South Africa, in Proceedings Sampling 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

An automated method, which is believed to be the fastest in the world and which can be used by mineralogically-untrained technical assistants, has been developed for the rapid location of native gold particles and other gold minerals down to 1 pm in size in ores, concentrates, and tailings using a scanning electron microscope. Searching of a 25 mm diameter polished block in 1 pm steps usually requires 3-4 h. Examples of the location of native gold and gold tellurides in drill core sections, in crushed ore samples and gravity and flotation concentrates, and in various metallurgical test products are given. The results have application in ore exploration, in guiding metallurgical test programmes, and in assessing metallurgical per- formance in testwork and in operating plants.

Jan 1, 1991