Search Documents

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

A device is described which is suitable for the automatic sampling of dust in dust laden flue gases. This device, called a Venturi Sampler, consists of two pipes each fitted with a suitably designed venturi.Both pipes are placed in the flue where one acts as an open-ended reference tube and the other as the actual sampling tube.The gas sampling rate is automatically controlled so as to maintain a zero differential pressure between pressure tappings in the two venturi throats. The venturies are so designed that under these conditions the gas velocity in the sampling pipe is always equal to the free gas velocity in the flue-that is isokinetfc sampling conditions are maintained.INTRODUCTIONThere is a constant need in industry for regular and accurate assessments of dust losses, both to assist in improving operating efficiencies in order to minimize losses, and to obtain accurate metallurgical balances. In many cases where sampling is carried out in dust laden gases, the existing sampling methods are both laborious and inaccurate, and often make no provision for changes in flue gas velocity while sampling is in progress.In the majority of cases where a measurement of dust losses in a stack or flue is required, a preliminary velocity survey is made with a pitot tube to establish the gas velocity at each of the points at which samples are to be taken. The sample of gas (and dust) is withdrawn through a tube connected via a flowmeter to an exhausting apparatus. Some means of removing the dust from the gas sample is placed in circuit ahead of the exhausting apparatus. This is often an alundum or paper thimble housed in a gas-tight container.The purpose of the flowmeter is to measure the actual flow of gas during sampling so that the sampling velocity at the inlet to the sampling tube may be calculated, and the flow corrected so that the sampling velocity will agree with...

Jan 1, 1959

By Bilodeau M. L

The paper describes a model which has been developed to assess the economic charac- teristics of base metal investment in Canada and the effects of past, present and possible future sharing systems, particularly mining taxation systems, thereon. The model is illustrated by applying the 1976 Canadian tax system to the economic characteristics of base metal discoveries made in Canada during the 1951-1974 period.

Jan 1, 1977

By Maxwell HW

Pacific Coal Pty Limited (a wholly owned subsidiary of CRA Limited) managed the interests of six members of a joint venture formed to mine and export eight million tonnes of export quality steaming coal from a mine developed at Blair Athol in the Bowen Basin of the Central Queensland coal fields. The mine is now operated by Blair Athol Coal Pty Ltd. Crooks Michell Peacock Stewart Pty Limited (CMPS) was awarded a project management and engineering contract for the total mine portion. Following a feasibility study, CMPS carried out an Optimisation Study which produced changes to the design of the project, thus resulting in the project budget being reduced by some A$13 million. In spite of a number of late additions to the scope of work, the project was completed at a final cost of A$148 million, many millions below the reduced project budget. The project was also completed several months ahead of schedule. Total services were provided to take the project from feasibility stage through to the establishment of an operational facility and included project management, planning and control, accounting and financial control, as well as the organisation of engineering, procurement, construction, industrial plant commissioning, and technical training matters.

Jan 1, 1986

By S Freij, P W, R Gunawan, D Zhang, B Feng

The Mt Whaleback iron ore mine is located adjacent to Newman, approximately 1200 km north of Perth, in the Pilbara District of Western Australia. Approximately 15 per cent of the waste materials are in the zones with high concentrations of sulfide and carbonaceous minerals and are referred to as æreactive shaleÆ. The reactive shale has the potential to undergo self-heating and can react with the ammonium nitrate (AN) based explosives used in mining operations, resulting in spontaneous combustion and spontaneous explosion. The sulfide-rich shales also have the potential to produce acid rock drainage (ARD). In the present study, over 200 shale samples have been collected from different locations in the Mt Whaleback iron ore mine, including blasthole drill cuttings, fresh mine faces and waste dumps. These samples have been systematically characterised for their geochemical properties. Based on the characterisation results, a pH test was developed as a cost-effective, fast and efficient tool for the assessment of reactive ground in the mining industry. This paper summarises the results of the sample characterisations and discusses the key findings arising from the interpretation of results. These results have significant implications in the safe storage of the reactive shales and the prevention of spontaneous explosion, spontaneous combustion and ARD.

Jan 1, 2005

By N Guresin, A Cooper, L Lorenzen, H Muller, S C. Dominy

Sampling and metallurgical test work during various phases of engineering?studies?is of?paramount importance for a robust processing plant design. When developing a process flow sheet, risks in achieving desirable financial outcomes are minimised by ensuring appropriate sampling and adequate metallurgical test work supports the engineering and cost estimation at each phase of project development.The quality and type of samples used for metallurgical test work are just as important as the metallurgical test work itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should take into account the spatial orientation, lithology, alteration, degree of oxidation, mineralogy and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical test work program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design.Snowden has observed that the quality of sampling and quantity of metallurgical test work carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are often the result of the plant design based on benchmarks of apparently similar orebodies or buoyant metal prices supporting cash flows until rectifications can be implemented.The paper will discuss important aspects of sampling and test work required for engineering studies in designing process plants based on industrial case studies.CITATION:Guresin, N, Lorenzen, L, Dominy, S C, Muller, H and Cooper, A, 2012. Importance of effective sampling and test work protocols for process plant design, in Proceedings Sampling 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By T J. Orr

The changing demographics of the mining industry make successful passing of knowledge and skills to the next generation critical. Training methods and technologies are being developed to meet this need. Twenty years ago classroom training was largely a one-way transfer of knowledge through instructor lectures. In contrast, instructors today can use virtual reality technologies to guide trainees as they fully participate in learning experiences. Trainees can interact with the virtual work environment, co-workers, and equipment without being exposed to workplace hazards. The speed of advancement in mine safety, health, and production training shows no sign of slowing in the next 20 years. Researchers at the National Institute for Occupational Safety and Health have studied and participated in the evolution of miner training. A look at training materials they have created in the past and those they are currently developing reveals changes in methods and technologies over time and also key characteristics which have remained constant. Possibilities for the future can be discussed in the framework of an implementation of virtual reality in new miner training sessions. The example computer-based training package teaches new miners to read mine maps and provides opportunity to practice navigation skills in a virtual mine. With this æserious gameÆ, trainees experience the look and feel of moving through an underground coal mine while in the safety of their classroom. During field-testing in 2007, trainees and instructors responded very favourably to this new way of learning. The software was usable by mine trainers with even limited computer expertise and could be installed on the affordable computers they were using for their more traditional slide presentations. The Underground Coal Mine Map Reading TrainingÆs foundation on past successful development strategies and its acceptance by todayÆs instructors and trainees provide valuable lessons for developing training materials, strategies, and technologies for miningÆs future.

Jan 1, 2008

By Mann LD

The Haveluck gold deposit, located 2.5km north of Meekatharra, contained 1,284,000 tonnes at an average grade of 1.8 g/t gold of drill delineated proved and probable ore prior to commencement of production. Following successful laboratory and pilot scale testing a decision was made to establish a 300,000 tonnes per year heap leaching operation. The ore, crushed to minus 100mm was stacked on an impermeable membrane and irrigated with a dilute cyanide solution. Gold was recovered from the resulting pregnant solutions by adsorption onto activated carbon and gold bullion produced in a modified Zadra process desorption plant. From the commencement of mining it was obvious that a high percentage of fine material was being produced which would adversely affect the percolation of the cyanide solution-through the leach heaps. A screening plant was incorporated into the crushing circuit which provided an oversize product satisfactory for heap leaching and an undersize for carbon-in-pulp treatment. Plant design provided for the slurrying of minus 0.8mm ore before feeding to the pachuca tanks. Initial practice was to use four tanks for gold dissolution and two for carbon contact. Vibrating screens were used through- out for the carbon-ore separation and the loaded carbon was stripped in the existing desorption plant.

Jan 1, 1982

By P C. Hagan, J Chen, S Saydam

Fully grouted cable bolts have been used in underground mining industry for more than 40 years and are becoming more and more popular especially when severe geological conditions are encountered, such as high stresses and large cross-section excavations. The axial performance of cable bolts are mainly relied on the load transfer process between the cables themselves and surrounding rock masses via grout annulus. Therefore, the selected grouts play a significant role in determining the reinforcement quality for underground openings. In order to better understand the mechanical properties of Stratabinder HP grout, which is one type of cementitious grouts commonly used in Australian underground coalmines, plenty of unconfined compressive tests are conducted on it. Following diverse standards, two different kinds of samples are prepared and tested with the w/c ratio ranging from 0.35 to 0.45. During the test important mechanical properties including uniaxial compressive strength (UCS) values, Young’s modulus, Poisson’s ratios and so forth are recorded. Based on experimental results, the effect of w/c ratio on the mechanical properties of Stratabinder HP grout is studied. Beyond that, influences of sample size on the failure mode, peak strength as well as residual strength of this kind of grout are summarised and analysed.CITATION:Chen, J, Hagan, P C and Saydam, S, 2014. Mechanical properties of cementitious grout serving in fully grouted cable bolting systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 269–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S Wangchai, D B. Hastie, P W. Wypych, A P. Grima

Industries that handle and process ‘dusty’ ores are facing increasingly difficult challenges to ensure sustainable operation and development. Most existing dust-control measures treat only the symptoms of dust generation and do not deal with the root cause/s of the problem. Many of these methods are also relatively inefficient in terms of controlling dust emissions. This paper summarises the various existing options available for dust control and some of their features, advantages and disadvantages. It then describes some of the new technologies that are being researched, developed and employed to minimise dust emissions by addressing dustability or dustiness and the dust generation mechanisms found in industry. Recent research results and case studies are presented to demonstrate some interesting findings obtained from this work. With improved understanding and modelling of dust generation mechanisms and bulk material dustiness, it is possible to achieve a step-change improvement in the design, troubleshooting and application of more efficient dust-control technologies.CITATION:Wypych, P W, Hastie, D B, Wangchai, S and Grima, A P, 2015. Research and application of new dust control technologies for the iron ore industry, in Proceedings Iron Ore 2015, pp 529–536 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Roldpo, M Vidigal, J F. C L Costa

The local cumulative distribution function (lcdf) of a selective mine unit (SMU) can be estimated by conditional simulations using the statistics derived from the sample points, generating multiple equally probable scenarios. Conditional simulations permit the evaluation of the lcdf at any support, taking into account the spatial variability, ie the variogram, and the two statistical moments, mean and variance, of the conditioning samples. The SMU ore losses and dilution depend on the mining method and mining equipment selectiveness that, in its turn, depends on the predicted block size. A new approach to predict ore loss and dilution was developed in this study. Monte Carlo simulation is used to randomly generate a grade value derived from the lcdf at the mining stage (Zs_mc(t)) in order to make a decision about the SMU destination, ie processing plant (ORE) or waste dump (WASTE). If Zs_mc(t) is lower or equal to the cut-off (Z_cut-off) the block is ORE and, conversely, if Zs_mc(t) is higher than the cut-off (Z_cut-off) the block is WASTE. Considering these binary destinations ORE/WASTE, at the mining time t, and combining each realisation of the simulated random function Zcs_i (X), there are four possibilities for each SMU simulated value: 1. the block was simulated as ore and is actually ore (OO), 2. the block was simulated as ore and is actually waste (OW),3. the block was simulated as waste and is actually ore (WO), and 4. the block was simulated as waste and is actually waste (WW).The dilution factor is given by possibility 3 (WO), while the ore loss factor is represented by possibility 2 (OW). These results comprise the classical classification and reconciliation plots used in the mining industry. The new procedure proposed in this paper is based on the use of all the equally probable simulations to define the ore loss and dilution factors. An application of this methodology was carried out at Vale's iron mine in Brazil. The grade of silica was simulated and 50 multiple equally probable 3D models were generated. The mean and the standard deviation of the ore tonnage (OO + WO) for the 50 realisations, was 233 Mt and 0.5 Mt, respectively. The mean grade increased for the diluted ore (OO + WO) as well as their respective coefficient of variation (CV). The CV increases from 62 per cent in the undiluted ore (OO), to 101 per cent in the ore, considering the dilution factor (OO + WO). The mean ore loss (OW) was 10 Mt and the waste tonnage dilution (WO) was 9 Mt.

Jan 1, 2009

By A Weston

Northparkes Mines is a joint venture between Rio Tinto and the Sumitomo group and is operated by Rio Tinto to produce copper concentrate from ore sourced from open cut and underground. Underground ore is mined with an owner operator workforce using the block cave method from the E26 deposit, with the first lift of the cave now completed. Development of the Lift 2 block cave commenced in March 2001 using a contract workforce. The Lift 2 Project required the mining of 14 700 m of decline and lateral development to establish a new mining horizon at the 9450 level and to develop two new conveyor declines. Also included in the scope was the excavation of a Crusher chamber to house the jaw-gyratory crusher. This paper describes the excavation of the hydroset chamber and orepass that sit immediately underneath the Lift 2 Crusher chamber. It includes risk assessment, planning, development of method statements and standard operating procedures, through to the excavation of the orepass and the installation of ground support in seismically active ground. There was a major ground failure in the backs of the conveyor feeder chamber during its excavation, which affected the excavation of the orepass due to its proximity to the breakthrough site.

Jan 1, 2005

By T D. H McGrath, W P. Staunton

Benchmarking, comparing an operation or process with the industry standard, is known to be a useful method for identifying plant optimisation opportunities, and in many cases providing the pathway to realise the benefits. The difficulty is generating the database of plant data necessary for a benchmarking exercise. Larger companies can benchmark internally; this option is not available to smaller companies, and the full value can only be realised with a comprehensive “industry wide” approach.The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has undertaken several comprehensive metallurgical industry surveys in the gold industry over the last two decades. Analysis of these surveys has demonstrated areas where many operations can benefit from re-assessment of their operating practices.This paper will review the work undertaken by the Group in this area, in particular the 1999 surveys of gold companies in the Australasian region, and the 2012 international survey of the industry. The challenges of, and opportunities arising from these surveys will be discussed. Some of the highlights from analysis of these databases will be presented as well as noting changes in processing practices observed by the Group over the last 20 years.CITATION:McGrath, T D H and Staunton, W P, 2018. Keeping up with the Joneses – the value of industry surveys and benchmarking, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 509–516 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

This paper reviews the developments in understanding of the entrainment mechanism and its modelling in industrial flotation processes over the last 30 years. Both valuable and gangue minerals in the pulp zone of an industrial flotation machine can be transported through the froth zone to the concentrate launder in the water which must also be transferred from the pulp zone to maintain a stable froth zone in conventional flotation. A size dependent portion of each entrained mineral continues in normal circumstances to the concentrate launder. The size dependency arises because the larger particles are able to drain more successfully from the froth region. Gangue minerals are recovered by a number of mechanisms, entrainment being an important one in many cases. The entrainment mechanism is discussed on the basis of the pattern observed in recovery û size data for minerals. Its industrial implications are discussed and means of minimisation of the importance of the mechanism are also discussed. Various means proposed for mathematical modelling of the entrainment mechanism are also described. The effect of process variables on key parameters in these models is reviewed. Properties of both the pulp and froth zones are discussed where needed and means of taking additional measurements with devices developed over the last ten years are discussed as part of the collection of more detailed data on the flotation process in general and the entrainment mechanism in particular.

Jan 1, 2005

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988

By J H. Heo, J H. Park, M J. Lee

In this paper, the challenging points regarding the high temperature physical chemistry of slags to achieve the improved and stable electric arc furnace (EAF) or electric smelting furnace (ESF) technology on the way to green steel will be reviewed, and the recent experimental and modelling research will be discussed. For example, the initial melting phenomena of hot briquetted iron (HBI) and the slag formation behaviour was observed using a high-frequency induction furnace. Main component of gangue oxides in HBI was SiO2, Al2O3, and CaO in conjunction with unreduced iron oxide. To increase the dephosphorisation efficiency, the distribution ratio of phosphorus between metal and slag was calculated using FactSage™ software, version 8.2 (CRCT ThermFact, Inc., Montreal, Canada) and was compared to the measured results. The optimisation of slag chemistry is required not only for maximum dephosphorisation efficiency with good slag foamability but also for minimum slag volume with less refractory corrosion in EAF process. The slag chemistry is also one of key parameters affecting the operation efficiency in ESF in view of FeO reduction behaviour, viscosity, sulfide capacity, etc.

Jun 19, 2024

A discussion on simulation tools to aid the development of robotics platforms is presented. The focus of the work is towards mining robotics platforms where operations are typically in unstructured, unpredictable environments and a high degree of dependability in their operations is required. It is argued that a test-based development approach leads to more robust solutions and faster development cycles than traditional single-track field-only development and that the key enabling technology for this development paradigm is the judicious use of simulation tools. The future direction of simulation for use in online applications such as active planning and as a means to assist tele-operation in high latency communication applications is also brief y considered together with the requirements for a useful simulation environment in terms of the simulator architecture. Finally, a case study is presented on the application of the discussed methodologies to an unmanned ground vehicle (UGV) for earth-moving tasks, which is being developed in an accelerated time frame with a transient development team.

Dec 6, 2010

By H Bao, M Nehring, M Kizil, P Knights

The mining sector, a notably energy-intensive industry worldwide, is a major consumer of fossil fuels, leading to significant carbon emissions globally. The move towards electrification, coupled with advancements in battery technology, has redirected focus from traditional diesel-powered solutions to battery-powered alternatives. This paper introduces a novel mining haulage system, termed the Battery Trolley system, and examines its theoretical foundations, configurations, and operational processes. It offers a comprehensive analysis of the system’s characteristics and limitations. Through a hypothetical road simulation, the study analyses various battery mining trucks, calculating energy consumption based on force parameters and tailoring battery sizes to contemporary materials and technology. When assessing various battery truck alternatives—considering aspects such as battery size, effective payload, duty cycle, energy efficiency, productivity, and single-shift production—a range of performance outcomes and characters become apparent within the mining context. The findings indicate that Battery Trolley configurations, requiring smaller battery capacities, entail lesser compromises on effective payload. Consequently, these configurations achieve a higher duty cycle, reduced energy consumption per tonne, heightened productivity, and enhanced singleshift production capabilities compared to Battery-only alternatives. The comparative analysis of Battery Trolley with stationary charging (BT-S) and Battery Trolley – dynamic charging (BT-D) underlines that battery Trolley systems are capable of overcoming the challenges associated with battery size, thus successfully fulfilling the production demands of large truck applications in mining. This positions Battery Trolley systems as a more advantageous option for the decarbonisation of mining fleets, underscoring their potential in contributing to the sector’s sustainable evolution.

Sep 1, 2024

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By W J. Botha

The Palaeoproterozoic Transvaal Supergroup in the northern Cape Province of South Africa hosts high grade (>60 per cent Fe) hematitic and specularitic iron and manganese mineralisation. The mineralisation is primarily exposed along the western margin or in the central part of a major interference fold structure known as the Maremane dome. The bulk of South AfricaÆs iron ore production is currently provided by two active mines, Kumba Resources megaton Sishen iron ore mine on the northern end of the dome, and the smaller Assmang Beeshoek mine on the southern closure. The undeveloped Sishen South deposit, which contains ~400 Mt of high-grade hematite ore, is located approximately 9 km towards the southwest of Postmasburg. It forms a linear extension of the Beeshoek mine and as such contains comparable laminated, breccia and conglomeratic iron mineralisation. The Transvaal Supergroup sediments were deposited in two distinct fault-controlled basins on the Archean Kaapvaal craton. Basement rocks in the western Griqualand West basin are formed by a carbonate platform sequence (Campbellrand Subgroup), which is overlain by a thick sequence of banded iron formation of the Asbesheuwels Subgroup. A major unconformity separates these rocks from the red-bed Gamagara Formation, which is correlated with the base of the Olifantshoek Supergroup. Diamictites and lavas of the Postmasburg Group have been thrust over these units from the west. The mineralisation process is related to regional scale supergene iron enrichment of Kuruman banded iron formations along the unconformity. During regional tectonism associated with the Kheis orogeny (2400 - 1700 Ma) the Maremane dome was uplifted, and the basal dolomite units thus exposed to erosion and karstification. The overlying banded iron formations collapsed into karst sinkhole structures where leaching of silica and enrichment of hematite occurred. Although the exact mechanism of the mineralising process remains unclear, karstification preserved components of the original concordant laminated and massive ores. These ores were subsequently eroded and deposited as conglomeratic and gritty ores down-dip of the Maremane dome in alluvial fan systems. A thin veneer of recent calcrete or Tertiary Kalahari clay beds masks the subsurface geology and most of the orebodies, thus ground geophysical gravity surveys proved excellent exploration tools to penetrate the surficial cover. These surveys were used extensively for delineation drilling and to deduce the subsurface geology and structural development of the area. Finally Sishen South orebodies were modelled with ModelVision software in an attempt to obtain an exploration template for the surrounding area.

Jan 1, 2005