Search Documents

By K Rozlapa, P Waters, H Middlemis

A major challenge for closure planning at mining operations below the water table is evaporation from final void pit lakes and concentration of salts, which can impact on downstream groundwater (and surface water) flows and quality. Where such impacts are deemed unacceptable, the closure approach that is often adopted is to infill the final voids with waste rock to above the pre-mining water table to prevent the development of a pit lake and subsequent evaporative losses. BHP Billiton Iron OreÆs Marillana Creek (Yandi) mining operations face these issues. The orebody is a channel iron deposit that forms the major aquifer in the region, which will be completely mined as a series of elongated open pits over tens of kilometres. The major constraint on mine closure planning was the stripping ratio of less than one, which means that there is insufficient waste rock to infill all areas to the pre-mining water table. Hydrogeological investigations and groundwater modelling indicated that standard mine closure approaches would result in pit void lakes becoming saline sinks unless the residual void geometry was optimised to minimise evaporation and maximise throughflow. The solution developed is a cost-effective long-term mine plan that meets all mine closure objectives, and involved:the selective infilling of all pits, largely using run-of-mine waste dumping with limited re-handling; the diversion of the major part of up-catchment creek flows around the mining operations to allow mining of the resource under Marillana Creek crossings, which in turn restricted overall aquifer recharge and reduced the elevation of the long-term water table; the diversion of some minor creek tributary flows into specific locations within the mine path to induce hydraulic gradients to maintain groundwater throughflow and water quality; and close integration of mine plan optimisation (mining and waste dumping schedules) with groundwater modelling scenarios to achieve acceptable environmental outcomes. This approach is designed to result in no reduction in downstream surface water flows or quality, maintenance of adequate downstream groundwater throughflow to support groundwater dependent ecosystems, and no reduction in the beneficial use status of the downstream groundwater resource.

Jan 1, 2006

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

By Sarkar B. C, Sen A. K

India is well endowed with vast reserves of banded hematite ore, about 12 billion tonnes, estimated by some conventional methods. Various authors have assessed this huge reserve using some advanced geostatistical methods. A Banded Iron Formation (BIF) belt named the `Singhbhum-Keonjhar-Bonai' belt in India has been chosen as a case study. In this paper, the experiences of Chiria iron ore, in particular, have been described. This study will finally create a dynamic mineral inventory after standardising the geostatistical parameters which will help to cater for the needs of the stringent quality requirements of the Indian steel industries.

Jan 1, 1995

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

Ore Reserves estimation for the two producing copper orebodies at Isa Mine, Mount Isa, Queensland is discussed. The principal estimation techniques used and discussed are first, a computer based inverse power distance weighted assay meshing technique, and second, a manual arithmetic averaging technique. The principles involved in these techniques are compared, and their areas of application indicated. A general comparison of the estimation of reserves with eventual production is presented.

Jan 1, 1979

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Deep hydrothermal fluids adjacent to the Alpine Fault move through the brittle-ductile transition to mix with convecting fluids from near surface environments. These tectonically driven fluids evolve mainly from prograde metamorphism at mid crustal depth (ten kilometres) within the ductile regime which has been elevated due to advection and drag on the fault plane. Through the onset of brittle failure and cataclasis within Alpine Fault mylonites, fluid overpressuring results in hydrofracturing and localized implosion. Along the length of the Alpine Fault, hydrothermal alteration varies on most levels (Table 1). There is an observable increase in Fe-Mg carbonate between the Waitaha and Taramakau Rivers (between Ross and Aurthur's Pass, respectively). Field studies concentrate to the north east of the Arahura River, noted for historical mineral wealth. Late meteoric fluids move through cataclasite, brecciated mylonite, and other open fractures. Chloritisation is the major retrogressive phase. Dolomitic hydrofracture veins (Figure 1) within coherent mylonites contain iron and copper sulphides. Notably, the enrichment in Fe-Mg carbonate towards the Alpine-Hope Fault intersection seems to represent a region of enhanced permeability possibly related to shallow seismicity, increased regional faulting, footwall variation, strike-slip dip-slip distribution, and/or topographical anomalies (ie saddles). Isotope studies identifying an 'Inboard Fault Gouge Calcite Zone' correlate to values from the Main Divide region at the headwaters of the Arahura River (Browning Pass-Wilberforce Valley) (Becker et aI, 2000). These correlations are supported by rare arsenic anomalies (avg l06 ppm n = 5, Figure 2) found in both regions which suggest that fluids may be interconnected at depth.

Jan 1, 2001

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By P B. Swart, P D. Erskine

Despite an increasing focus by media, communities and activists driving an elevated regulatory focus in Australia and indeed some other mining jurisdictions, the mining industry globally has had limited successful mine lease relinquishments and transfers to support a next land use.Critique from anti-mining lobbyists frequently uses the large estimates from historically abandoned mine sites to influence risk-averse regulatory reforms to improve environmental performance. The mine rehabilitation regulatory processes in Australia, and specifically in the State of Queensland, are thus largely in place to prevent mining operators from abandoning their obligations.Regulatory responses to the lack of mine rehabilitation and closure performance in the last five to ten years have primarily focussed on compliance and enforcement of rehabilitation conditions in environmental approvals. Additionally, financial assurance measures have been tightened to protect against abandonment of rehabilitation obligations by the Industry, including the Chain of Responsibility legislation (Queensland Government, 2016b) in April 2016, to hold to account those who have benefitted from mining and processing/refining projects, and then avoid their environmental obligations.CITATION:Swart, P B and Erskine, P D, 2018. Are our closure planning and regulatory processes adequate to identify, quantify and appropriately transfer residual risks after successful mine rehabilitation?, in Proceedings Life-of-Mine 2018, pp 155–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

A review of the factors controlling stope wall behaviour such as excavation geometry, rockmass strength, induced stress, ground support, blast damage and drill drive layout is undertaken. In addition, the advantages and disadvantages of single lift stope geometries linked to vertical crater retreat are also analysed. Finally, key components of multiple lift stoping such as cut-off slots, production rings, stope undercuts and drawpoints are studied in detail.

Jan 1, 2000

By P Trotta

The paper provides a structured methodology to investigate metallurgical problems within the operating concentrators. The strategy uses classical metallurgical data analysis as well as pulp, solution and surface analysis to determine the reasons for particular behaviours. The approach applies equally to all mineral-processing operations. To demonstrate its effectiveness a case study, based on work conducted at Pasminco Rosebery Mine, is described. In this work, the classical metallurgical analysis indicated that a significant amount of sphalerite reporting to the lead concentrate occurred as liberated particles. A combination of pulp, solution and surface analysis supported the hypothesis that the liberated sphalerite was recovered by inadvertent activation by lead ions. Laboratory studies have indicated that the use of sodium carbonate, by itself and in combination with zinc sulphate and sodium cyanide, when added to the lead regrinding mill can depress sphalerite flotation, resulting in an improvement in the lead grade/recovery curve. When this approach was tested in the plant other more dominant issues masked any positive effect the addition of sodium carbonate may have had. The plant trial highlighted the real need for additional regrinding capacity.

Jan 1, 2002

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

By B Bradák, D Asahina, S Saydam, S Akdag

Human exploration of Mars has been on the horizon of scientific goals for decades now, and as part of the objectives of human missions to various planets, one of the possible goals is opening new economic frontiers by the potential extraction and utilisation of resources, eg mining minerals and using surface regolith (Neukart, 2024). A comprehensive understanding of surface morphology, lithostratigraphy, basic structural geology, and civil engineering technology is essential to conduct mining operations for resource extraction on extraterrestrial planets. For instance, proper assessment of the risks associated with excavation and infrastructure construction under unique environments such as low gravity, surface irregularities, and the presence of regolith is fundamental. Such knowledge has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander (Knapmeyer- Edrun et al, 2021; Banerdt et al, 2020; Giardini et al, 2020). Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults exist and form regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. In this study, we focus on so-called graben structures, one of Mars’s common tectonic structures (Plescia, 1991; Banerdt et al, 1992; Hoogenboom Hagen, 2014). The study aims to provide additional information about the tectonic environment during the formation of such features and, in addition, the internal mechanical-rheological structure of Mars, revealed by the geometrical pattern of faults modelled and simulated in a laboratory environment.

Sep 1, 2024

By Hunter GW

This paper gives an account of the filling system at Mount Isa from surface fill production to stope discharge underground. A brief explanation of the surface facility and reticulation is given prior to the discussion on aspects of underground reticulation. These include fill hole types, pipe and breastplate installation, wear characteristics, etc. The different types of fill and their respective applications is mentioned as a prelude to a general overview of the mining considerations associated with fill placement and its role in the long term planning strategy at Isa Mine. Some practical aspects of stope preparation and filling procedures are outlined for the various stoping methods. Finally a brief outline of future fill developments is given.

Jan 1, 1982

By Hall S, Upton D

WMC Resources Ltd nickel operations have expanded significantly over the last three years. Production capacity has increased at mine/concentrate, smelting and refinery processes to such an extent that WMC now ranks within the top three or four producers of nickel metal in all forms. The stainless steel industry remains the dominant user of nickel. WMC's forecast is for stainless steel production to grow at 2.8 per cent per annum off of the 1995 peak, with much slower growth in the short-term as the stainless steel inventory overhang unwinds, followed by a return to higher trend growth rates. WMC's forecast for the long-term growth in demand for primary nickel is three per cent per annum off the 1995 peak; again, slower growth in the short-term before a return to higher long-term trend rates. This projection is towards the optimistic end of the range of industry experts. It equates to a requirement for new primary nickel of 25 000 to 30 000 tonnes of annual capacity each year.

Jan 1, 1996

By F Melcher, M Wiedicke, A Wittenberg

Ferromanganese nodules form a specific category of widespread marine mineral deposits. The tremendous increase in metal prices during the last decade raised new economic interest in their exploration. The German Federal Institute for Geosciences and Natural Resources (BGR), which had been engaged in nodule research in the 1970s and 1980s, renewed its activities on this subject based on an exploration contract with the International Seabed Authority, signed in 2006. BGRÆs licence area û comprising 75 000 km2 û is located between the Clarion and the Clipperton Fracture Zones. In this so-called nodule belt north of the equator the sea floor reaches water depths of >4000 m. About 900 million tonnes of manganese nodules are expected there. In this study the fine-scale distribution of important elements in manganese nodules and crusts from a variety of locations was investigated. Besides 11 samples from the RV SONNE cruise SO-25, numerous samples from additional locations were included in this study for comparison. In general, the sample suite includes two genetic types of precipitates, manganese nodules and Co-rich crusts. A detailed characterisation of the distribution of major, minor and important trace elements in manganese nodules based on in situ microenergy dispersive X-ray fluorescence (¦-EDXRF) analysis is presented here. The data are compared with bulk major, minor and trace element data as well as with quantitative electron probe microanalysis (EMPA) data sets. The element distribution maps and profiles produced by ¦-EDXRF analysis with short or extended (in case of profiles) counting times, allow precise selection of æregions of interestÆ for further detailed investigation using high spatial resolution techniques (eg scanning electron microscope (SEM)-EDAX; laser ablation-inductively coupled plasma mass spectroscopy (LA-ICPMS); isotopic studies).

Jan 1, 2008

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal and gold industry have increasingly placed mining in the media spotlight. A lack of appropriate standard environmental guidelines has resulted in inconsistent responses and assessments of current and proposed mines. These inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere. A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991,the legislation that largely drives the nationÆs environmental policies and guidelines. The tangible outcome of this research program will be water quality and impact management guidelines integrated into a decision-making framework. The result of this unification will assist in the development of viable mineral deposits and minimise environmental impacts. The framework will be derived from a synthesis of three objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland regions. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Wide consultation with representatives of the mining industry and regulator groups will occur frequently during the development stages of the framework. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

ecent work on decoppering lead is reviewed; CuS is formed rapidly even from dilute solutions of copper in lead. he mechanism of decoppering is discussed, and an explanation for the retention of metals such as silver in lead is dvanced. As decoppering tin appears to be an analogous process, the Cu-Sn-S system is studied at 300¦C. CuS, hich is not, an equilibrium product, is found in decoppering drosses. In the removal of nickel from lead, Ni3pb2S2 formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by tirring in sulphur. Decoppering bismuth is thermodynamically favoured, but is complicated by the occurrence of uBiS2. The Cu-Pb-S system is the only one of the four studied where the equilibrium can be calculated simply, as ' resence of ternary sulphide or other phases invalidates calculations based on binary data.

Jan 1, 1970