Search Documents

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

Shizuyuan deposit is a compound type of greisen and skarn associated' with W,mo,Sn,and BI mineralization. Tungsten-bearing skarns are located at the contacts between carbonate rocks and granitic stock. Ore-bearing greisens occur in the top of granite or superimpose on the skarn rocks. Although mineralization and alteration are heterogeneous,there are clear patterns in the preferred associations of minerals on all scales, and an orderly sequence can be distinguished. The sequence of mineralization Isom bhar. Gsesus-.contactròoctaard is characterized bòyVtia of L, a4[~!kient assemblages W(mo,~P),,,W,(,Mo,Sn,Bi),Sn (Bi), and Sn. Skarn formation is divided into an early sk.arnoid stage and a late metasomatic stage. The skarnoid stage formed grandite garnet and diopside pyroxene in the limestone. The iron content of garnets decreases significantly away from the granite, whereas pyroxenes maintain a relatively constant diopsitic composition. The metasomatic skarn stage is charac- terized by hydrous silicates. The mineral assemblages of. greisens are regularly distributed in space. The feldspar-quartz-fluoride was usually formed in-the deeper part, upwards giving way to muscovite-quartz, and topaz usually occurs in the uppermost part. The distribution, and miner- alogical relationships of alteration facies suggest that they formed as a result of the progressive reaction of an ascending hydrothermal solution with aluminum-nearing limestones an-d granitic rocks respectively. The ore elements were mobilized and deposited in association. with hydrosilicate alteration of skarns and greisens.

Jan 1, 1987

Economic and technical reasons forced the mining industry all over the world to increase the unit size of mineral processing equipment. in large flotation cells, this development leads to problems in areas of air dispersion and keeping solids in suspension. Outokumpu, an operating mining company, designed and developed a mixing mechanism for large flotation cells at its own concentrators and also studied problems related to tank design. Ideal conditions for flotation can only be achieved if the flow pattern created by the mixing mechanism fits well into the tank configuration and the risk of short circuiting is minimized. In large deep flotation cells, four different zones can be found which improve the behaviour of large cells when compared to small cells. Selectivity is increased and in some cases final concentrate grades can be produced from the rougher cell. The largest units have also been used as final cleaners in some installations. When modernizing old plants by installing fewer larger flotation cells, immediate and substantial savings in power consumption are achieved. Additional power savings are made in pumping costs because of simpler circuit design and decreased circulating loads

Jan 1, 1978

By Alesse V, Belardi G

A new class of collectors, Mercapto-Benzo-Oxazoles (MBO), exerting selective action on copper sulphides in the presence of Pb, Zn and Fe sulphides (galena, sphalerite and pyrite), has been synthesised in co-operation with Enichem's Donegani Insitute. The collectors have a mixed aliphatic-aromatic structure and contain functional groups which form chelates with copper. Some reagents of this class having hydrocarbon chains of various lengths have been laboratory tested on a complex sulphide ore containing chalcopyrite, galena and sphalerite in pyritic gangue. Comparative flotation tests have permitted selection of the best collector for chalcopyrite, namely Methyl-Mercapto- Benzoxazole (MMBO). Systematic flotation tests have been performed with this reagent, varying collector concentration, grain size of the feed, pH and flotation time. The results obtained show that the synthesised collector is much better than potassium-amylxanthate (KAX) as regards selectivity towards Pb and Zn. Moreover, it is possible to work at natural pH (6-7) and the flotation rate is higher. In fact in the rougher stage with 80 g/t of collector at natural pH, a copper grade of 7.14 per cent was obtained with a recovery of 73.87 per cent, while the grade with KAX did not exceed 2.11 per cent for a recovery of 73.54 per cent. The amount of Pb and Zn reporting in the copper concentrate was eight per cent and ten per cent respectively, while with KAX it was no lower than 24.34 per cent and 22.71 per cent in that order. After two minutes flotation a copper grade of 5.2 per cent with 52 per cent recovery could be attained, against a grade of 2.5 per cent and a recovery of 44 per cent in the case of KAX. The efficiency of this new collector has been ascertained on two samples of complex sulphide ores of diverse mineralogical composition.

Jan 1, 1993

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

By C Menzies

Hydraulic Monitor mining at Solid EnergyÆs Spring Creek Mine has proven to be a safe and effective method of extracting steeply dipping thick seams at production capabilities approaching one million tonnes per annum.   This paper traces the development of Hydraulic Monitor mining from its initial introduction into old workings at Strongman Mine, its refinement at Strongman 2 in shallow, thick and steep workings, through to its introduction into the deep, very thick seams at Spring Creek Mine. This last step of the progression came with all the added complications that come with depth, particularly flammable gas.   This paper will describe the various changes in mining conditions that dictated the performance of the monitor, how the mine layouts were changed to adapt, and the various operational systems that were put in place, to allow a safe and productive operation.

Jan 1, 2007

Part of a four-year course in metallurgy, dealing with metallurgical process engineering, was designed for students to acquire knowledge and skill from physical science, metallurgy, process engineering, and social science. Principles of education, and guidelines obtained from a study of professional practice, indicated that students may learn effectively through a planned sequence of problem-solving exercises based on the diverse functions of metallurgists in industry. The more important characteristics of the curriculum and a few illustrations of the problems are included. An outline is given of the current procedures used to develop parts of the curriculum, and of the students' diffic- ulties and achievements.

Jan 1, 1984

By Staude W, Rosser A

Due primarily to the publication of the Fitzgerald Report the impact of taxation on the mining industry and the amount of taxes actual- ly paid by the industry have become items of intense debate. However, the discussion has been governed more by impassioned rhetoric than considered logic. It is equally as wasteful to the economy for the mining industry as a low cost efficient export earner to be punitively taxed, as it is for the industry to be given excessive taxation assistance. A comparison of the effect of five tax- ation policies on the cash flow of a capital intensive mining project is presented. The policies considered are Liberal 1969, Liberal 1976 with and without the coal levy, Labor 1975 and Labor 1976. The mining project used in the analysis is modelled on published estimates for the proposed Nebo coal project. The analysis is equally applicable to any large mining or petroleum development.

Jan 1, 1977

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The intention of this work was to con struct a machine on a pilot scale which could hoist a mixture of ore and water through a height of 300 metres and to operate the mach- ine to determine the parameters which affect the success of upscaling the machine to a pro- duction unit size. The investigation into this form of hoist- ing was stimulated by the interest shown by Roan Selection Trust (RST) into the Mills Pulse vessel system. Agreement was reached between these two parties that RST would in- vestigate the Mills System and determine if this system, shown to be successful on a Lab- oratory scale, would be successful as a pro- duction unit. The investigation has shown, however, that for practical reasons, the Mills System is not satisfactory. As a consequence, the RST system was invented and developed which on a pilot plant scale would be capable of lifting 7,000 tonnes of ore per month. The inventions included amongst other things, a valve to control the flow of the abrasive mixture of ore and water, a new pumping system employing a filter mechanism, and a method of changing the downward direction of flow of the pipe mixture through the plant to an upward flow in the hoisting pipe. The valve has operated to pressures equivalent to 300 metres

Jan 1, 1973

By S Nowosad, O Langefeld

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

By Lawrence PR, Hoffman W

The dissolution of gold from various ore-bodies is discussed in terms of extraction rates and reagent consumptions during leaching. Gold dissolves slowly in cyanide but reagent consumptions are usually satisfactory. In almost all cases where excessive cyanide consumptions occur, similar high consumptions result with other lixiviants. Recovery of gold from cyanide solution is well established and comparatively simple technology.Gold dissolution in thiourea is faster than cyanide but significant consumptions of thiourea, due to both adsorption and oxidation, occur. Gold recovery from thiourea solutions is likely to be more difficult than from cyanide.Chlorination of gold is very fast in acidic conditions but excessive consumption of chlorine occurs for ores containing greater than 0.5% S. Reprecipitation of gold and handling of acidic chlorine solutions are both significant problems. The mechanism of gold reduction onto activated carbon creates difficulties in the carbon in pulp process for recovery of gold but means a simplification in the production of bullion from loaded carbon.

Jan 1, 1984

By M Rimes

This paper describes a technique to predict achievable head grades and likely variances from target grade for the Shovelanna Iron Ore Project, in the Pilbara region of Western Australia. The block model from which the production schedule is produced was created from a wide spaced drilling program and was classified as an Inferred Resource under the JORC Code. Ideally, production schedules and target grades would be determined using a combination of Proved and Probable reserves. However sometimes it is necessary to consider the requirements of potential off-take parties who have specific grade tolerances. A technique is needed to simulate mining sequences and grade variations early in the planning process, using an æexplorationÆ block model rather than the normal æminingÆ block model. Marketing contracts require examination whether the target grade {Fe, P, SiO2, Al2O3 can be kept constant, or must be revised during the life of the mine. A model (written in ExcelÖ using Visual Basic macros) develops a feasible, close to optimal, mine plan from block model data. Cut-off grades for minable ore are chosen. The model evaluates ore tonnage, grade and stripping ratio against depth. Outputs at this stage include plots of slices through the orebody, at nominated x, y and z coordinates, showing ore grade, waste, drill hole locations and topography. The model then searches for a feasible satisfactory mine plan. The initial grade target is the average for the identified ore blocks. The available block list (ABL) at any time is the set of ore blocks, any one of which can be mined without removing any other ore block. The entire initial ABL has an unacceptably large ætotal grade stressÆ, defined as [(Grade-Target)/Tolerance]2, summed over the four relevant minerals {Fe, P, SiO2, Al2O3}. The model trims the ABL, removing the block most harming the total stress. Trimming is repeated until the total grade stress reduces to an acceptable level. The trimmed ABL defines the first mine campaign. Removing the trimmed block set, a second ABL is exposed, which is again trimmed and mined. The process is automatic: a few seconds computation provides a complete mine plan. Re-running the model with adjusted grade limits quickly shows whether a uniform target can be achieved or whether the target must be modified during the mine life.

Jan 1, 2007

By D L. Head

Critical risk management (CRM) has become one of the latest safety buzz terms in mining. Everyone seems to be doing it, everyone seems to know about it, yet we are still having fatalities in our industry from well understood hazards such as mobile equipment amongst others.

May 5, 2022

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Bure R

Approximately 2.4 million ounces of gold and 11.3 million ounces of silver have been produced from the Umuna Lode by Misima Mines Pty Limited between June 1989 and the end of Decemeber 1996. Reserves remaining at the end of December were 32.1 million tonnes at 1.0 gram per tonne gold and 9.7 grams per tonne silver. To attain precious metal production of this volume, an estimated K60,000,000 (1996 Kina) was spent on exploration alone. from the 1940s to the present day. Exploration expenditure for the 1996 calendar year was approximately K4,400,000. With such a large investment in exploration, large quantities of data were generated and stored in various forms. To make best use of this data, it was necessary to organise and systematically store this data in a form compatible with a modern Geographical Information System (GIS). The Umuna Lode on Misima Island is a low sulphidation gold- silver deposit dated at 3.5 ¦ 0.2 Ma. The deposit is controlled by the 50 to 100 metre wide Umuna Fault- a moderate dipping, brecciated clay- chlorite- carbonate altered, normal fault zone. There is approximately 230 metres of mostly dip slip offset on this fault, which is measurable by the offset of the Cretaceous schist, marble and greenstone host sequence. Late Miocene microdiorite spatially related to the Umuna Lode does not appear to be genetically related to the gold- silver mineralisation. GIS was introduced to Misima at the end of 1995 and until recently has been mostly used for data storage and retrieval, the over- laying of various data sets to assist in targeting prospective areas, and as a drafting tool. The use of data-driven, predictive data analysis is the most recent effort in maximising the use of the extensive Misima database. By characterising the key controls and properties of the Umuna- type mineralisation, a Weights of Evidence, data-driven analysis produced a prospectivity map of Misima Island. The purpose of this map was to identify prospective areas yet to be explored and to assess the effectiveness of exploration to date.

Jan 1, 1997

By I Özen, G Chitumbura

A paper identifying anticipated challenges in the extraction of the N3500 Orebody at Glencore Xstrata Copper’s Mount Isa Copper Operations was written in 2007. The paper identified the depth of the deposit, the anticipated high stresses, talc alteration and issues with ground support as factors that may affect production. A number of strategies were planned to cope with these issues. After six years of extraction those strategies are evaluated and additional measures taken are outlined. Strategies to cope with the limited mine life are presented, and methods to overcome additional challenges encountered during production are described.CITATION:Chitumbura, G, Matthews, D, Özen, I and Jackson, S, 2014. One mile underground – mining the N3500 orebody at Mount Isa Mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 265–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014