Search Documents

The basic make-up of the majority of currently produced bulk explosives has changed little in the last 20 years. These explosives would be described as mature in a life cycle analysis. Therefore these explosive products and the practical rules for their use are well understood and well established. In recent years there has been interest in low density explosives, predominantly due to ammonium nitrate shortages and the associated increase in the cost of explosives. In the use of low density explosives some of the practical rules for the more commonly used bulk explosives do not apply. Therefore a shift in the thinking among users is required. At a number of mines low density explosives have been trialled or are being used, utilising the practical rules that apply to bulk explosive products. This has led to poor blast results in many situations. These poor blast results have often then led to a reduction in the use of low density explosives at the mine. This reduction does not acknowledge the advantages that can be gained from this product in the area of reduced cost of mining. This paper looks at low density explosives and discusses how and why these products work. Included in the paper are some practical ideas and examples of how low density explosives can be effectively used at the mine site.

Jan 1, 2007

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By Gregory O, Winters BI, Garlick C, Rogers H, Ye ZC

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multi- hearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80% metallization) from the rotary kiln and completes the reduction process to produce iron of nominally 3% carbon. As the melter operates at around 1500 ¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

By T Kilpatrick

Managing heat stress on Australian mine sites is a complex and enduring challenge due to the combined and variable contribution of environmental conditions, physical activities, and protective equipment. Inappropriately managed, heat stress can place significant physical strain on workers, leading to serious and chronic health issues. Additionally, excessive heat stress can dramatically reduce productivity, with 30 per cent of workers reporting a loss of productivity due to occupational heat strain. In Australia, due to increased absenteeism and reduced work performance, heat strain is estimated to have an annual economic burden of over $8 billion.

May 5, 2022

The explosion at Appin Colliery on July 24th, 1979, demonstrated the need for a large scale facility to simulate an underground type explosion and study its effects. The effects of an explosion cannot be established quantitat- ively using small scale models. A gallery was constructed for this purpose at Londonderry Centre and commissioned in Feb- ruary, 1980. It is 50 metres long, 2.7 metres in diameter, capable of withstanding an internal pressure of 210 kPa and is the only facility available for this purpose in Australia. The gallery has provided valuable inform- ation on blast effects of explosions in tunnels and is to be used for testing the performance of explosion arresting devices, further invest- igation of explosion effects, research into basic explosion phenomena and instrumentation development. Additionally, it will provide a demonstration facility for training purposes.

Jan 1, 1981

By Perring CS, Vearncombe J. R, Ho SE, Groves DI

Large Late Archaean greenstone belts in Western Australia, Canada and Zimbabwe, contain abundant mesothermal gold, volcanogenic massive base-metal sulphide, and komatiite-associated Ni-Cu mineralization. These greenstone belts are similar in many respects to convergent and accretionary plate margins found in the Pacific rim; modem environments which are cor-respondingly rich in gold and base-metal mineralization. The giant gold placer deposits of the Late Archaean Witwatersrand Basin (the world's largest gold producer) formed in a foreland or retro-arc basin; in a similar tectonic setting to much modem placer mineralization around the Pacific. Gold and volcanogenic base-metal sulphide mineralization are abundant in Late Archaean terranes and the Pacific rim because1. gold mineralization is a product of convergent margin tectonics, and 2. accretion in convergent margin orogens provides the best chance of preserving base-metal mineralization related to submarine volcanism.It is therefore likely that the abundance of gold and base-metal sulphide mineralization in the Late Archaean reflects the widespread growth and sta-bilization of continental crust via tectonic processes broadly similar to those operating in the present Pacific basin.

Jan 1, 1990

Before I begin this paper, I thought that it would be important to start with a brief background on myself. This will give some insight into where I am coming from with some of the ideas presented in the body of the paper. I studied mining engineering at the University of New South Wales, graduating with Honours in 1999. When I finished university I was offered a job with PricewaterhouseCoopers in Sydney, working in the Energy and Mining Group of the Audit practice; which I accepted. I have been working at PricewaterhouseCoopers now since January 1999, completing an accounting conversion course at the University of Technology Sydney along the way. I am currently beginning my Professional Year for Chartered Accountant qualification. During my later years at university, continuing on through the start of my working career, I have been involved with the Sydney Branch of The AusIMM; firstly, as a student representative and, now, as the Young Professional Representative. Therefore, you can probably see that I will have very different young professional experiences than some of my peers who have been working on mining sites. The purpose of this paper is to examine the challenges that face graduates who are entering the industry and what solutions are used to ensure that this entrance is as smooth as possible. A challenge has then been made to the industry and The Institute in the form of further observations on ways that this entrance may be improved and the development of graduates to be more effective. In preparing this paper I have discussed various graduate experiences with some of my colleagues in order to see what some of the challenges they, themselves, face now and, also, going forward. I also discussed with them what they see as solutions to these challenges, drawing on some of my own experiences in a different company environment.

Jan 1, 2000

Partnering has come to prominence in the Australian construction industry in a formal sense this decade. The high level of disputation in the building and civil construction industries in the 1980s drove its development in both Australia and North America. PartneringÆs use has been most prominent in the construction industry, particularly in the civil and construction sectors of the industry. It has found favour in some mining development projects, one of the most notable being BHP MineralÆs Cannington project in NW Queensland. This paper examines the requirements of successful partnering agreements and describes in detail the mine development partnering agreement at Cannington. In particular, the paper discusses the authorÆs experience and recommendations for partnering to avoid contractual problems and achieve win û win project outcomes for all parties to major mining projects.

Jan 1, 1999

By Richards AG

The stimulus of major capital expenditure in establishing open cut coal mining operations in the Hunter Valley led Coal & Allied Industries to look to a computer based information system as a tool to assist mine management in day to day operating decisions, as well as to provide a base of comparative data to help in long term equipment procurement decisions. The mine information system was conceived as an integrated set of three subsystems; costing, production recording, and maintenance. The maintenance management features of the system are closely keyed to a policy of preventive maintenance and maintenance costing based on user specified parameters. Central to this policy is the maintenance work order, which may be created and updated directly via interactive procedures at visual display terminals. The, system was designed for on-line processing in a multi-mine shared operating environment. Each mine controls its own data capture, and most other processing functions directly from terminals. The system is currently operational on the Combined Group Services Pty Ltd FACOM M150 computer, located in Newcastle, NSW.

Jan 1, 1983

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

By B M. Moudgil

Atomic force microscopy (AFM) has become an important tool for understanding the nano- to molecular scale mechanisms predominant in multiphase systems. In flotation research, the use of AFM holds promise for unlocking and establishing fundamental mechanisms, ultimately leading to significant advances in process performance. From measuring and characterising surface forces, the structure of molecules at interfaces, and nanoscale features on flotation media, AFM is a powerful tool that has only begun to impact flotation research. Highlights of advances made in the utilisation of AFM for flotation research at the University of Florida are given with an emphasis on interpreting the mechanisms behind calcium activation in phosphate flotation and the impact of nanoscale asperities on collector-born surface hydrophobicity.

Jan 1, 2005

By Y Zhu, D J. Williams, M O’Neill, C Zhang, X Lei

A cover of inert material overlain by topsoil is required over compacted, seawater-neutralised red mud, a waste product from the refining of bauxite to produce alumina. The cover is to be revegetated, and it is necessary to demonstrate that the potential evapotranspirative-driven uptake of salts from the seawater-neutralised red mud will not impact the revegetation. An instrumented column was designed and constructed to test the evaporation-driven uptake of salts from compacted red mud into an overlying cover material with a thickness limited to 600 mm. The PVC column is 1.2 m high, with a 200 mm internal diameter. The column is instrumented with up to ten of each of moisture, suction, salinity and temperature sensors, together with a data logger, designed and manufactured at The University of Queensland (UQ) in Brisbane, Australia. The sensors were installed through the wall of the column at various depth intervals, with each set of sensors located at quarter points around the circumference of the column. Two pressure transducers were installed in the column to monitor the change of water level due to rainfall and evaporation. The column was filled with compacted red mud to a depth of 600 mm overlain by 600 mm of cover material, both sourced from the Queensland Alumina Limited (QAL) site in Gladstone, Queensland, Australia. The column is installed on a building roof at UQ, alongside a weather station, and will be subjected to the prevailing weather conditions for up to 1 year in the first instance, during which time the weather conditions and sensor responses will be continuously monitored. This paper reports on the instrumented column set-up and the early results obtained from the test.CITATION:Zhang, C, Williams, D J, Lei, X, Zhu, Y and O’Neill, M, 2018. Instrumented column testing of salt uptake from compacted red mud into a cover, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 220–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By McIlveen GR

The water pollution hazard posed by the derelict Conrad mine site, to the water and associated stream sediment of Borah and Maids Creeks and the nearby Copeton Dam storage, has been assessed. Mine water, tailings and tailings dump leachate have polluted water and stream sediments in Borah Creek downstream of the mine site. Acidity, arsenic, copper, lead, iron, silver and zinc are the principal pollutants. Under dry and low flow conditions, mine water was found to be the dominant polluting source, however, leachate and run-off from tailings dumps were also significant under and following wet conditions. Soluble arsenic, lead, iron and silver species in mine water and leachate were found to be rapidly incorporated into sediments, but acidity, copper, and zinc persisted in the creek water. Under low flow conditions, the water of Maids Creek is polluted with copper and zinc (up to 4.4 and 34 mg/l for copper and zinc respectively) and the pH is decreased (from pH 5 - 7 to pH 3 - 6) by entry of Borah Creek water. Values found in Maids Creek were variable and related to flow regime and distance downstream from Borah Creek confluence. Water in Copeton Dam storage, having a much larger volume of water with a higher bicarbonate buffering capacity (50mg/l versus 15mg/1), is not affected by entry of Maids Creek water. Polluted sediment from Borah Creek has contaminated Maids Creek for 2km downstream to Copeton Dam storage. Stream sediment downstream of the Borah Creek confluence, contains up to 1.0% As and 1.4% Pb in the less than 200 micron size fraction. Under high flow conditions, arsenic was found to be moved out from the mine site as insoluble species, associated with suspended sediment in Run-off.

Jan 1, 1988

The last decade has seen a very rapid development in TBM tunnelling. Some trends are purely technical or economical and others relate more to preferences of different interests. Power levels have more than doubled and thrust levels too. Shield machines are developed to be able to handle harder rock and the open TBMs are made more feasible for `difficult' rock. What is right and what is wrong is more a matter of opinion, but one thing is certain: TBMs now are a useful tool and no longer an experimental work-shop for the enthusiasts.This paper highlights some recent developments and indicates some probable future ones. A few features that have increased the open TBMs' ability to cope with ever harder rock and also to overcome problems with poor rock are discussed in detail, using the Atlas Copco JARVA Mk 27 -the most powerful TBM built so far - as a reference.

Jan 1, 1993

By P Willems, J B. Crow, R Dale

Open pit mining commenced at Lihir Island in 1997 and is undertaken using a conventional drill, blast, load, haul methodology. Unique challenges at the operation include an active geothermal system, a well-developed advanced argillic blanket in the upper portions of the orebody and high rainfall. Grade control is effective utilising routine blast cone sampling. While this provides ‘just in time’ grade information for mill blending, there are opportunities to improve scheduling of mill feed, based on material classification of clay types and sulfur grades. The nature of the clay can impact on the handling properties while the sulfur grade is an important guide for autoclave blending, required for refractory gold. Drilling below the pit floor introduces hazards from the identified geothermal field. A trial Reverse Circulation (RC) program was implemented with the aim of defining four benches below the active mining bench. A comprehensive risk analysis, including the geothermal environment, was undertaken to design a drill collaring procedure with pressure diversion equipment. Operator exposure was minimised through ‘nil on foot’ principles with the driller located in an onboard cab, utilising remote rod handling. Sampling personnel operate in an elevated platform with access to protective covering. Samples from blastholes and the RC holes are processed at two site laboratories. One provides conventional Au fire assays with additional Infrared Combustion (Leco style) S analysis. The second laboratory collects material classification details from portable XRF (pXRF), near infra-red spectrometry (ASD) and Hardness Indicator Testing (HIT). An existing workflow was updated by the site to deal with the additional samples and ensure production ‘turn around times’ were retained for short-term planning. This required some changes to drying temperatures, compositing and screen sizing for the material classification. All results from the two laboratories are loaded into a centralised acQuire database for estimation into a single block model that informs the 13 week medium term planning (MTP) schedule. This paper describes some of the logistical issues faced when drilling in a geothermal area. It also discusses the selection and commissioning Quality Assurance of the sampling equipment and drill rig. Integration of the resulting assay data with existing resource models is also explained.

Mar 22, 2022

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By Ward B

Central Colliery was developed to exploit large underground reserves in the German Creek lease. It was planned from the outset as a retreating longwall operation and is the first longwall mine in Queensland. Longwall mining is not new to Australia but all previous experience has been confined to the coalfields of New South Wales. There was no precedent for longwall extraction in the markedly different geological setting of the Bowen Basin in Central Queensland. Various investigations were thus carried out during the initial development of Central Colliery, prior to the installation of the longwall, to ascertain the geotechnical characteristics of the coal seam and the adjacent strata and to predict the performance of the heading and pillar design as mining proceeds to depth. Laboratory tests showed the coal to be weak with an unconfined compressive strength of 9.6 MN/m2. Site inspection and geophysical correlation revealed a shear zone and extensive intraformational shear planes in the seam. The latter were found to exert a controlling influence on rib reaction in the headings. This behaviour was predicted by finite element modelling of the development headings which indicated that mining induced stresses in the coal would be relieved by block movement of the ribs. A chain pillar width versus depth curve was established for yielding pillar design based on empirical and computational methods. This gave pillar widths from 25m to 48m over the proposed depth range of 150m to 300m. Finite element modelling of the 25m pillars chosen for the first gateroads confirmed the overall stability of the design but suggested that rib spall could be significant in the adjacent tailgate. (1) Chief Mining Engineer, Capricorn Coal Management Pty. Ltd., German Creek Mine, Queensland (2) Senior Engineering Geologist, Coal Division, The Shell Company of Australia Limited, Melbourne

Jan 1, 1986

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By P A. Williams, P Leverett

Many of the worldÆs stibnite deposits are found in orogenic zones and are mesothermal or epithermal in origin. They commonly occur near contacts between intrusives and metasediments. However, the spatial extent of anomalous Sb levels around such deposits is not well documented. This project has aimed to gain a better understanding of the mineralogy and geochemistry of Sb by deriving solubility and thermochemical data for some of the most common secondary Sb minerals. This has then been applied in field exploration for Sb ore deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023