Search Documents

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100% recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after twelve years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By D S. Scovira

The effect of blast vibration on highwall stability is a common concern for many open pit mines. Vibration in such a case is a typical near-field blast vibration situation. Vibration modelling in the near-field of a blast requires consideration of both the amplitude and frequency attenuation of waveforms with distance. Most existing blast vibration models are designed for far-field vibration and do not simulate the frequency attenuation and its effect on waveform shape. With the advent of electronic detonators it is desirable to quantify the effects of blast delay on the amplitude as well as the frequency of blast vibrations. A suitable modelling tool is proposed here. At present, a blast vibration model with double attenuations(amplitude and frequency) has been developed at Orica. The present model simulates the amplitude and frequency attenuations separately using different transfer functions. The amplitude attenuation is modelled according to the non-linear relation between the peak particle velocity (PPV) and the charge weight scaled distance established from the signature hole vibration. The frequency attenuation is modelled with the signal broadening based on KjartanssonÆs transfer function û a linear model for attenuation of waves. The model is capable of taking multiple sets of signature waveforms as input to improve the modelling accuracy of the wave propagation in the geology at a site. The screening effect of the earlier firing holes in the path of a later firing hole is taken into account on not only the amplitude, but also frequency attenuation. The present blast vibration model is suitable for modelling both near-field and far-field blast vibrations. It yields reasonable agreement with measured field data for the near-field vibration examples discussed.

Jan 1, 2007

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

By R Pozo, F Reyes

Codelco Chile is currently developing the El Teniente û New Mine Level Project (NMLP) in order to increase ore production by seeking to mine the ore deposit located under the current operational orebody. Reserves of 2000 million tonnes (Mt) have been quantified, which will be extracted as from the year 2017 by using the panel caving and progressive sinking method. Codelco and SKM Minmetal (SKM) jointly developed the project prefeasibility stage (PFS), closing these studies in March 2008. The first part of the project approach is to replace mine production currently feeding the Colon concentrator facilities with 137 000 tonnes per day (t/d), focusing attention on a production increase from the year 2026 up to 180 000 t/d. Project efforts have also been centred on maximising the contribution of new technologies for both construction and operational phases of the New Mine Level, together with selecting the best mine infrastructure to keep El Teniente operations going on for the next 50 years. Implicit in this is the inherent improvement of a variety of current Mina El Teniente process and management practices. The plan is to reduce actual mine operational risks and take advantage of new opportunities afforded by the project, which is in effect a greenfield project with respect to the implementation of fundamental changes in the labour and business environment. In addition, issues related to human resources, maintenance and management, materials handling, establishing centralised operations and accesses, automation and remote operations control and power efficiency could also be addressed. The project, beyond the New Mine Level exploitation, considers the mineÆs future potential, with a second deeper exploration in prospect named Deep Level. Finally, the project identifies features that would add value to the mine operations, in an initiative named æSpace for Future TechnologiesÆ. This will allow the eventual implementation of new electrical equipment and the application of mechanised technologies and other process improvements for the mine development.

Jan 1, 2008

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

By A Robertson

Australia has been slow in adopting the use of underground space as a part of our urban planning process. Australia has one of the highest levels of tunnel advance per capita per annum in the world, yet the use of underground space in our cities appears difficult for our planners and politicians to comprehend, not withstanding the general availability of good quality rock and contractor expertise in Australia. However, the lack of space in our urban areas is being highlighted as our major cities expand outwards and people and businesses gravitate towards city centres. Typical potential underground space uses include car parking, self-storage and archiving facilities, water storage, underground quarrying, small industrial facilities and another layer of traffic (electric and fuel cell) and services network. Historically, blasting in high density population areas has resulted in blast vibrations and blast overpressures exceeding the limits, which in some case have been set extremely low in terms of peak particle velocity (PPV). This makes conventional blasting difficult, often requiring low charge weights per delay and associated small blast sizes and slow advance rates. However, the introduction of new technologies, such as computer aided drilling, electronic delays and low-energy explosives has made this task considerably easier. Although more expensive than conventional blasting, excavation by blasting using these products and technologies in relatively good quality ground is believed, in most cases, to be less than the cost of mechanical excavation. In this paper, the authors look at innovative trends in underground quarrying, underground commercial space and tunnelling and put forward their concept of future excavation demand, future product requirements and technical specifications to the drill and blast community.

Jan 1, 2007

By P J. Harris, D J. Bradshaw

Surface oxidation of sulfide minerals, such as that found in the regions of a sulfide ore body near the water table, can have a significant impact upon flotation. This theme has been explored for Merensky ore type sulfides where an ore containing pyrrhotite, pentlandite and chalcopyrite was thermally oxidised and the role of potential remedies investigated. Back-scattered scanning electron microscope images are presented showing the oxidation layer which formed in the mineral surfaces. These oxidation layers were depleted in both sulfur and iron with incorporated oxygen. Flotation recovery rapidly decreased with increasing oxidation, particularly after 27 days and reached a plateau after 50 days. Up to 27 days, this effect could be partially overcome with higher collector additions. Oxidation had more impact upon the finer size fractions, particularly for pyrrhotite. For more heavily surface oxidised samples, ultrasonic treatment prior to collector conditioning was found to improve flotation recoveries. This treatment had the greatest effect upon chalcopyrite particles. Sulfidisation was successful in restoring the flotation recovery of the heavily oxidised sulfide minerals. Longer sulfidisation conditioning times were not conducive to good flotation recoveries of both oxidised pyrrhotite and pentlandite due to oxidation of the freshly formed sulfide surfaces. For maximum flotation recoveries of oxidised pyrrhotite, pentlandite and chalcopyrite, different sulfidisation conditions are indicated. It appears likely that in a mineral processing operation treating oxidised Merensky type ores, two stages of sulfidisation employing different conditions would be required.

Jan 1, 2005

By C Vejrazka

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.The occurrence of air blasts is one of the principal mining hazards in block caving operations between the time of first undercutting and breakthrough of the cave to surface. As such, it needs to be managed continuously, and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. Unfortunately, there is little literature on how to practically approach air blast risk assessments in a way that can be incorporated in the day-to-day operation of a mine. Previous methods of assessing air blast risk were tedious and results were often unrepeatable.With the extension of the E48 Lift 1 extraction level, it was necessary to assess the air blast risk for the extension drives and develop operational guidelines for production from the extension. A review of the methodology for assessing air blast risks revealed substantial improvement opportunities.This paper outlines the principles used for air blast risk assessments at Northparkes Mines and the methodology employed to achieve efficient, repeatable and auditable results.CITATION:Vejrazka, C, 2016. Northparkes Mines’ current air blast risk assessment practices for block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 257–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

It is argued, that plate convergence, i.e. subduction, at other than right angles under a continental margin may lead to compensa-tional transcurrent faulting in the sialic environment. In this pro-cess the introduction of ultrabasic slivers, derived from the down-going oceanic crusial plate, along this fault may occur. This regi-me, both compressive overall and tensional along the transcurrent fault, will contain numerous indications for ongoing igneous and tectonic processes (such as volcanism, hot springs and frequent earthquakes).Examples for this scenario are California, the hinge between the Alpine- and Appennine orogens and the island of Sumatra.Igneous manifestations of subduction will be present both as inter-mediate intrusions and/or andesitic piles. The intermediate volca-nics may be intensely altered (chloritic, propylitic, argillic). Silice-ous breccias and banded chalcedonic sinters may be commonly found. This entire scenario is indicative for epithermal gold mine-ralisation.

Jan 1, 1990

The concentrating plant of the Broken Hill South Limited was described in Proceedings No. 44, Australasian Institute Mining and Metallurgy, December, 1921, by Wainwright and Read. It was erected on the present site in 1907 and 1908.From that date, the plant has undergone various alterations consistent with metallurgical improvements. By 1925, the timber work of the gravity secti"on had seriously deteriorated, so much so, that, when the machinery was working, the floors and supports vibrated badly, causing heavy maintenance costs.In 1928, it was decided to erect a new gravity-treatment section, to be followed later by a new flotation section.

Jan 1, 1932

The first steps towards the use of artificial intelligence to manage ground conditions have been made. Millar and Hudson (1993) outline the theory behind the use of neural networks in monitoring rock engineering performance.

Jan 1, 1994

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By G Kluck, N Stoitis, D R. Seaman, R A. Lauten

The presence of clays, in particular clay slime, may complicate many mining operations. Clay slime particles may possess a negative or positive charge depending upon the pH in the process and their presence may lead to reduced recoveries in flotation processes. It is assumed that slime particles may adsorb onto the surfaces of the minerals to be floated and by doing so, reducing the efficacy of the flotation chemicals. In this work it is shown that addition of a small amount of dispersant, either a polyacrylic acid or an anionic polyphenolic polymer, increases the recovery of copper and gold, both in laboratory trials and in plant testing of an ore with high clay content. Measurements of adsorption isotherms reveal that the tested dispersants show preferential adsorption towards the clay minerals present, suggesting that the improved recovery upon dispersant addition occurs by prevention of attachment of clay slime particles onto primarily chalcocite but also chalcopyrite.CITATION:Seaman, D R, Lauten, R A, Kluck, G and Stoitis, N, 2012. Usage of anionic dispersants to reduce the impact of clay particles in flotation of copper and gold at the Telfer Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Logsdon, T R. Clark, T I. Mudder

Oxidation of pyrite and other metal sulfides is accelerated by the activity of acidophilic iron- and sulfur-oxidising microorganisms. The ideal biocide for controlling biocatalysed acid rock drainage (ARD) would be inexpensive, inhibitory toward sulfide-oxidising bacteria at low concentrations, relatively non-toxic toward non-target organisms, degradable in the environment outside the zone of application, stable and long-lived in the impacted environment, sufficiently mobile to penetrate into piles of waste rock or tailings, and effective regardless of the metal sulfides present. A potent agent for combating ARD that fits these criteria is the thiocyanate anion (SCN-). The objective of this study was to determine the effectiveness of thiocyanate in controlling or preventing ARD within several types of sulfidic waste rock and tailings. Results were evaluated within a context encompassing process water and solids management strategies employed at different precious and base metal mines. Sulfidic rock was treated with solutions of potassium thiocyanate and subjected to accelerated weathering tests in lab-scale humidity cells, trays, and columns. Certain tests also utilised solid phase copper thiocyanate (CuSCN) to evaluate a ærelease on demandÆ strategy. Leach solutions were analysed for parameters indicative of ARD including pH, redox potential, conductivity, acidity, sulfate, iron, and certain heavy metals. Two larger scale field tests were also initiated by personnel at separate mines using, in the first case, ore containing a pyritic component in large columns and, in the second case, waste rock containing base metal sulfides in lined pits. Humidity cell tests showed low concentrations of thiocyanate solution applied to pyritic waste rock could reduce ARD formation by 90 per cent or more compared to untreated controls, with the residual release of ARD components (eg sulfate, Fe, acidity) probably reflective of strictly chemical oxidation of the sulfides by molecular oxygen. Thiocyanate applied at a concentration of 22 mg/kg to waste rock from a base metal mining operation in large laboratory scale columns reduced acidity and sulfate release by 75 per cent to 80 per cent compared to untreated controls. This extent of reduction in ARD may not meet discharge water quality criteria, but has the potential to significantly reduce lime consumption and sludge production in a conventional neutralisation facility. The use of a solid-phase metal thiocyanate compound (CuSCN) at a dosage of 194 mg/kg pyritic ore resulted in the following per cent reductions in leach solution parameters in comparison to controls: sulfate (78 per cent), acidity (93 per cent), dissolved Fe (99.4 per cent), and dissolved arsenic (99.9 per cent). This compound has the further advantage of being relatively stable until needed, dissolving only in the presence of an acidic and oxidising ARD solution. If this line of investigation progresses favorably, it offers the possibility of an ARD prevention technique that may be applicable in some settings. Mine-site pilot scale tests with pyritic ore resulted in reductions in sulfate (56 per cent) and Fe, As (66 - 68 per cent). In sum, thiocyanate at relatively low concentrations dramatically reduced ARD from sulfidic rock in a simulated heap. The pilot test using waste rock containing base metal sulfides has begun only recently. A preliminary process design and cost estimate was made for fullscale application of thiocyanate to waste rock at a hypothetical gold mining operation producing 5000 tpd of ore and 10 000 tpd of sulfide containing waste rock. The combined capital and operating costs for the full-scale thiocyanate application facility were about $US 0.25/tonne of waste rock and $US 0.50/tonne of ore. Although thiocyanate is readily available commercially, it also occurs in process solutions associated with certain types of mining processes. Such solutions after selective treatment might be recycled to sulfidic waste rock or tailings, rather than being treated for thiocyanate degradation.

Jan 1, 2003

By R Marchant, D Willingham

"Predictive maintenance (also known as PHM or equipment ‘health monitoring’) refers to the intelligent monitoring of equipment to avoid future equipment failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:reduction of equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetimeautomatic determination of the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis avoidance of costs of unnecessary maintenance and unexpected failures improved safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data preprocessing is performed using advanced statistical and signal processing techniques. In the case that data isn’t available for the full range of operating modes, operating scenarios can be simulated. Machine learning techniques are then used to estimate equipment health. Once tested, predictive maintenance algorithms may be operationalised in an IT environment such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.In this paper, we use both historical and simulated data of the plant under various modes of operation including run to failure, and we then leverage machine learning techniques in MATLAB to estimate degradation and remaining useful life. This technique, of combining both simulation models and machine learning, in the areas of predictive maintenance and equipment health monitoring has been adopted by Safran, makers of aircraft jet engines, since 2007. They now have over 160 modules developed (Lacaille and Aurelie, 2015).Citation:Willingham, D and Marchant, R, 2016. Predictive Maintenance Using Simulation and Machine Learning, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Brady KT, Pattenden G

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1984

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

When a joint venture is established between a major and a minor, the co-venturers often have a number of divergent interests; the major may have put up significantly more capital into the project and will want to protect its investement; the major may have more financial resources and be more readily to commit capital to the project; the major may have more technical resources and expertise to provide to the project; the major may have other competing demands for its capital; the minor may be relying on rapid development of the project as its sole source of cash flow. Successful joint ventures arise when the co-venturers understand each others' interests and attempt to satisfy these interests. This could be achived by having a clear process and timetable for development of the project coupled with clear rules for distribution of income, the commitment of capital to the project and the provision of inter-company services. If divergent interests are either regulated clearly or eliminated, both co-venturers are more likely to seek common objectives in the joint venture with less scope for conflict. This paper, written from the perspective of a major, examines means of establishing successful joint ventures between majors and minors.

Jan 1, 1997