Search Documents

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By May P. M

The role of chemical speciation in alkaline cyanide solutions is discussed by reference to recent experimental data from the authors' laboratories. It is shown that serious gaps exist in our present knowledge of the thermodynamics of cyanide complexes in solution. Nevertheless, using the available data and the JESS suite of computer programs it has been possible to develop a simplified chemical speciation model for alkaline cyanide solutions under conditions relevant to the gold extraction process. Some possible implications of the model for plant operations are Discussed.

Jan 1, 1991

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

Drill and blast operations account for 12 - 15 per cent of total mining costs. This paper looks at a comparison between electronic detonators and non-electric detonators, focusing on the cost benefits associated with the high precision of the timing sequences of electronic detonators. An analysis of the total mining costs was made on two main case studies; one on a quarry in South Australia (Martin, 2007) and the other on a project undertaken at Sunrise Dam (Vaughan et al, 2007). The criteria used in the analysis included; the resulting fragmentation, a vibration analysis, crusher throughput and productivity analysis such as excavator cycle times, dig rates of the excavator and bucket fill factor. The results indicate that there were consistent production improvements and hence reductions in total mining costs attributed to the use of electric detonators. An increase in the degree of fragmentation gives lower crushing costs as more material passes through as undersize. This reduces truck delay time at the crusher, which in turn gives higher truck and shovels productivity as well as higher dig rates for the excavators.

Jan 1, 2008

By D Hodson

Current classification of resources is entirely a subjective task. The various international reporting codes (such as the JORC Code) provide Competent Persons and practitioners with little specific guidance on the standard of work and levels of uncertainty required to classify resources into Measured, Indicated and Inferred. Furthermore, little guidance is given in the conversion of Resources to Reserves and the potential impacts on classification of uncertainties in the modifying factors. Working back from the intended use of the resource estimates, and in understanding the tolerance for uncertainty by the end user of such estimates, insights into the objective and requirements of classification can be determined. Following this approach a comprehensive set of (quantitative where possible) guidelines have been determined that will ensure resources meet the desired objective of each classification, and are consistent and comparable. The guidelines look at what is required for each step in the resource estimation process in order to ensure the final resource estimate meets the desired level of confidence. This approach provides a transparent, comprehensive, justifiable and largely objective method of classification. The implication of introducing such a guideline or approach is to highlight areas of a resource estimation that do not meet the requirements (ie drive the uncertainty beyond the objective) and then focus in on the risks that may flow on from that particular uncertainty, to mitigate or attempt to control those risks.

Jan 1, 2006

By Dixon D. R, Sparrow G. J

Pressure leach liquors from the pressure oxidation of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore were treated to remove iron, either by pressure oxidation (the Hematite process) or with particles of magnetite (the Magnetite process), followed by cementation of various metals with zinc dust to obtain a purified solution from which zinc was electrowon. Satisfactory iron removal was achieved by both processes after neutralisation to pH 4.5 or 5.5. Pressure oxidation of the liquor at 200¦C and 690 kPa oxygen overpressure, conditions similar to those of the Hematite process used in the zinc industry, resulted in the precipitation of the iron as hematite. With the Magnetite process, an iron hydroxide was precipitated onto magnetite at atmospheric pressure and ambient temperature and removed by a magnetic separation step. The performances of both these processes for the removal of iron are compared. It is concluded that the Magnetite process offers considerable cost savings. Other impurities, in particular arsenic, were also removed with the iron in both processes. Cementation at pH 5.2 and 85-90 ¦C with 3.5 g/L zinc dust reduced the levels of copper, cadmium, and nickel to a satisfactory level and subsequent electrolysis in a laboratory cell gave an acceptable deposit of zinc.

Jan 1, 1989

By D R. van der Meulen, P Ande, D J. Lunt

Pressure hydrometallurgy is becoming an increasingly common unit operation in the treatment of gold and base metal ores and concentrates. The design of an adequate and appropriate pilot-scale testwork program is, therefore, essential in order to minimise the risks associated with developing a project in which autoclaves form a key part of the operation. This paper identifies the approaches that have been taken in the piloting of oxidative and pressure acid leach operations. Particular emphasis is placed on the determination of scale-up ratios between the pilot and commercial plants and the pilot-plant run durations. The issues, both metallurgical and project-specific, that can impact these key parameters are reviewed.

Jan 1, 2004

Water resources legislation in Brazil is evolving in a number ways. The nature of water resource ownership has changed in the last constitution (1988) so that now all water remains the property of the state and not the individual. There is also an increasing amount of legislation to control water access from the environment and regulation over water quality for water discharged. Finally, in some regions charging for water has been introduced and this is expected to become more wide-spread over the next few years. Increasing government attention to water legislation creates an increased need for mine sites to improve water management. As a fundamental basis for this, it is necessary to make robust estimates of mine site water balances, which also requires knowledge of the regional water balance to provide context for the mine water use. A conceptual model for mine site and environmental water balance is presented. Issues associated with conventional water monitoring are discussed. It is proposed that introduction of automated monitoring to provide comprehensive and consistent data is attractive. However, there remain a number of cultural and practical impediments to purchase, implementation and maintenance of effective monitoring, which are summarised.

Jan 1, 2009

The Crown Minerals Act 1991 has introduced some significant changes to the New Zealand mining industry, not the least of which relate to the ability of miners to obtain access to land to conduct mining activities. This paper briefly reviews the relevant provisions of the Crown Minerals Act dealing with access arrangements, considers some typical features of access arrangements and examines a number of areas where problems may arise.

Jan 1, 1992

By Jin C, Shuyi L, Yuanbiao Z

This paper describes the structure, performance, principle and effectiveness of a new laboratory type of composed-forces field separator utilising the composition of the magnetic force, vibrating force, pulsating force, gravity and fluid-viscous force etc to separate fine feebly magnetic valuable minerals. Compared with the pulsating high gradient magnetic separator, this separator possesses unique advantages of higher enrichment ratio and higher recovery of the magnetic component.

Jan 1, 1993

By R H. Boffey

The Osborne copper-gold deposit was discovered in North-West Queensland in 1989. Underground production activities commenced at Osborne deposit in April 1996. This paper will examine technical and operational aspects of the underground mine during its development to a 1.2 Mtpa operation . Technical aspects discussed include geology, mine design and mining methods, equipment fleet selection and capital infrastructure. Operational aspects discussed include the evolution and performance of the integrated work teams that are utilised at Osborne to perform all mining and maintenance activities.

Jan 1, 1998

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

Subsidence prediction methods can be divided into two basic types: empirical and analytical. Empirical methods are based largely on a combination of experience, intuition and observations from a large number of observed subsidence data. They are simple in their application, but they are not based on any principle of mechanics. Analytical methods are based on equivalent material modelling principles, where the ground surrounding the extraction is mathematically represented by idealised materials that deform according to the principles of continuum mechanics. Wide applicability and improved understanding are the principal advantages claimed for this approach. In NSW, significant progress has been achieved in the area of subsidence prediction during the last ten years. Empirical prediction curves are available in NSW for predicting the ground movement in the Southern and Newcastle Coalfields. A' comparison of subsidence values predicted from these curves with the actual monitored values indicates that the curves are adequate for use in conjunction with the existing damage assessment methods. Future research for improving the existing empirical prediction curves can only be justified if it is cost effective. There are several numerical models currently in use in NSW for predicting subsidence. The models do not appear to be superior in their ability to predict subsidence when compared with the empirical curves. the performance of these models will no doubt improve along with advances in defining strata properties and failure mechanisms.

Jan 1, 1991

A summary of the more important work by previous workers is followed by brief descriptions of the rock formations and regional structure. Type examples of the various forms of mineralization are described and the conclusion is drawn that there has been one main period of ore formation, namely, during the "Viti Revolution" in the mid or late Miocene.INTRODUCTIONThe Crown Colony of Fiji is comprised of a group of some 250 islands situated between latitude 160 sand 21 0 S and longitudes 1770 E and 1780 w: By far the greater, part of the total area, 7,083 sq. miles, is contained within the two main islands, Viti Levu 4,053 sq. miles, and Vanua Levu 2,128 sq. miles, and it is to these that most geologists have directed their studies. The most detailed work has been in the Tavua Basin, north coast of Viti Levu, centering about the mining town of Vatukoula and the geology of this area forms the subject of a separate paper by Blatchford (this volume p. 13).The present contribution summarizes geological knowledge of Fiji, at the time of writing (Feb. 1952), with particular reference to the known mineralIzation, but excluding the Tavua Basin. For general descriptions of Fiji's topography reference should be made to the recent works of Derrick and Dunkin.PREVIOUS WORKERSPeriod 1840-1930Prior to the gold rush of the early 1930s the visiting geologists concerned themselves in the main with the struc...

Jan 1, 1953

**Add abstract here**

Jun 1, 2010

Where tunnel rounds are based on the burn cut, faster advance could often be achieved by increasing blasthole diameter from (the conventional)

Jan 1, 1981

By A Radici, M Attwill

The Dampier Port Upgrade Project (DPU) involves an upgrade to Hamersley IronÆs Parker Point iron ore port facility at Dampier, Western Australia. The $US700 million DPU Project will increase Hamersley IronÆs shipping capacity at Dampier from 72 million tonnes per annum (Mtpa) to 116 Mtpa. The DPU Project comprises a new car dumper facility and rail spur, an upgrade to the existing stockyard and conveying system, a new screen-house and a 450 m wharf extension with two new shipping berths and a new ship-loader. This paper discusses the innovative design and construction of the new car dumper facility, which is capable of automatically unloading 240 car iron ore trains at a rate of 10 000 t/h. The facility design is unique compared to more conventional designs currently in operation, and greatly improves operation and maintenance functions.

Jan 1, 2005

By Yu A. B

An experimental study of the packing of a coal heap has been carried out. The bulk density of a coal heap is considered as a function of a number of variables, viz flow rate, conveyor belt speed, the height of the disengagement point of the conveyor belt, coal particle density, moisture content, the size of the heap and coal particle size distribution. The effects of the dimensionless numbers resulting from dimensional analysis on the packing density of a coal heap have been experimentally examined and analysed. Based on the experimental results, equations have been formulated for the estimation of the bulk density of a coal stockpile. The validity of these equations are checked by comparing the predictions with measurements of real industrial Stockpiles.

Jan 1, 1991

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993