Search Documents

Bauxite Resources Limited is grade drilling in its Western Australian Darling Range tenements to firm up resource definition and to develop mine plans. The Darling Range bauxite is generally in shallow deposits with minimum overburden. In the northern tenements, the ore is characterised by a higher silica layer which may extend from 0.5 to 1.5 m below, which high grade bauxite is found to a depth of four to 7 m. When grade drilling samples are taken, every 0.5 m and the recovered sample is weighed, logged and bagged. To eliminate splitting errors, the whole sample over the short interval is pulverised. Twinning holes variations are observed when using various drill rigs. Diamond core has been shown to give close to 100 per cent recovery and grades have been verified by digging bulk samples. As such, diamond core is used as the reference. It is intended to include sonic drilling as an alternative to diamond cores. This presentation details and attempts to explain the reasons for the observed variations in the various drilling methods used by Bauxite Resources Limited. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Mar 1, 2010

The Bureau of Mines, with a history of mining research since 1910, still seeks improvement in safety and health along with improvement and competitiveness in the mining industry. Much promise of such improvements lies in new technology, and this is particularly the case in the still growing coal mine sector, although much Bureau research is long term, high risk, aimed at new concepts.The miner's environment is a primary concern, involving technologies of contaminant monitoring and control in high production scenarios. Contaminants arising from diesel use, alternatives to high speed rotary cutting and more efficient dust removal are being addressed, and drilling efficiencies, better monitoring through unitising operations and insitu rock dust monitoring are particular features.

Jan 1, 1991

The development of paraprofessional courses in metallurgy and related disciplines, by the Department of Technical and Further Education in New South Wales, is outlined in this paper. The changing nature of metall- urgical educational requirements is summarised, and various attendance patterns discussed. The potential advantages of the sandwich system of College attendance, to the more distant sectors of the mineral processing and metallurgical industry is outlined. Some of the likely future trends in technician education are presented. These include the need to respond to the changing expectations of technician employers, as shown by industrial surveys, the role of experiential learning, the need to integrate courses so that students can build on prev- iously completed courses, the possibility that future technicians will require a multi- disciplinary background and the provision of easier access to technical college facilities by potential students and industries.

Jan 1, 1978

By McKenzie C. K, Stewart R. S, Simpson J

Blast control in small scale underground mining leads to improved fragmentation control, improved control over overbreak and dilution, and the optimisation of drilling and charging operations. Greatly improved control can be achieved through blast monitoring, to confirm proper implementation of blast designs and blasthole charging. Further improvements can be achieved through simple modelling, enabling blastholes to be placed in the correct locations and charged with the correct weight and strength of explosive. Improved design can be shown to significantly reduce overbreak and dilution, and even ground support costs. In one mine in Quebec, open stopes of widths varying from 2.5 metres to four metres and dipping at 36¦ to 38¦ were designed to achieve zero dilution using open sloping blasting practices. The first stope designed in this manner was monitored in detail and achieved its objective.A method for contouring damage around blastholes is presented as a basis for selection of drilling patterns, with particular application to the control of overbreak and dilution. Contouring can be used to provide reliable estimates of either overbreak or damage (where rock is broken het reynainc in nlarr)

Jan 1, 1993

Faced with rising costs and lower metal prices, several Ontario base metal sulphide mines have changed their method of mining to vertical crater retreat mining. This is a bulk mining method that utilises large diameter holes and mines successive cuts remotely by blasting and cratering the bottom of the drill holes. The orebody is mined from the bottom up. The method in turn has required a change in materials handling to cope with the greatly increased productivity.   This paper presents an overview of vertical crater retreat mining in the Sudbury area using examples from several producing mines. The paper reviews the history of vertical crater retreat mining, various methods of applying vertical crater retreat layouts, the development of in-the-hole drills capable of drilling the large diameter holes required, methods of explosives loading and blasting to achieve the required cratering effect, methods of ground support including backfill placement, and the ore loading equipment presently being utilised including remote control load-haul-dump units and continuous loaders.   The safety aspect of vertical crater retreat mining has been of concern, and was the focus of a provincial inquiry. The benefits in improved safety are demonstrated through an analysis of various records kept by the mines and provincial agencies.   Future trends can now be envisaged, particularly in relation to deep mining. Some experimental work which could have practical applications, is described.

Jan 1, 1989

By Fuller P. G, Dugan K. J

Artificial support can be used to improve wall stability in open pit mines. This is examined for a particular case where the factor of safety for a slope is kept constant by using artificial support as the slope angle is increased. It is demonstrated that the savings in excavation generally exceed the cost of support. However, in order to correctly judge the eco- nomic impact of artificial support on the project, all the elements relat- ing to the use of artificial support must be taken in account.

Jan 1, 1989

The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance as a defence against the Global Economic Crisis. Five of the six RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites. The sixth is for Sino IronÆs Cape Preston Project in Western Australia. This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules. The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest semi-autogenous grinding (SAG) mill new liner placement rates ever observed by Russell Mineral Equipment (RME), as would be expected with two, independent Machines working simultaneously in the one mill. The liner replacement rate, averaged over the whole reline is good (27 per cent improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation. This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ædouble headÆ mill liner handler by others. Early performance of EscondidaÆs new RUSSELL TWIN 8 System performance is then compared with recent single machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved. The preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform to develop data collection templates is also discussed in Appendix 1.

Jan 1, 2009

Magmatism and mineralization are features of the New England Orogen in late Palaeozoic- Mesozoic time. Voluminous silicic and mafic magmatism, both orogenic and post-orogenic in association, was accompanied by abundant mineralization in the earlier phases. Later activity passed transitionally into less vol- uminous felsic to mafic intraplate basaltic volcanism, with possible migratory hot spot activity through the flanking Oxley and Sydney Basins. Only minor mineralization took place at this stage. A new inerpretation links these magmatic and mineralizing events to a major thermal cycle. A New England hot spot(?) complex evolved in latest Carboniferous/early Permian time. Its activity was partly obscured by orogenic magmatism as Australia moved slowly over magma sources in the deep lithosphere. In Triassic time Australia's movement changed direction and faster drift over the waning hot spot complex produced multiple migratory intraplateòactivity. The volume of magma and hence abundance of ancillary mineralization was related to age of the hot spot, speed of the continental movement over thermal sources and extent of accompanying orogenic activity. The New Eng- land Orogen hot spot(?) possibly existed for 165 Ma, with mineralization changing over this Period.

Jan 1, 1987

Particles finer than 10 um often cause problems in flotation. The current under- standing of the nature of the following effects is discussed: slime coatings on particles, carrier flotation, increased froth stability, entrainment of ultrafine gangue, excess reagent consumption, slower rate of flotation, more reactive surfaces. The review emphasizes the principles underlying these effects rather than details of progress in practical solutions to the problems they cause. The princi- ples of selective flocculation and floc flotation and the various approaches to achieving selectivity are discussed. Hydrodynamic effects on floc growth are reviewed. The evidence suggests that satisfactory performance in the ultrafines fraction will be achieved only by simul- taneously increasing the rate of flotation of the ultrafine valuable mineral and de- creasing the rate of entrainment of ultra- fine gangue.

Jan 1, 1984

There was a time, in the memory of some here tonight, when the annual meeting of The Institute was a nostalgic occasion. Often, in the 1920s, there was comment on the decline of Australian mining and on the lack of new mineral discoveries. When some of our Presidents prayed then for a new Bendigo, and instead were given a Mount Isa, they were justifiably disappointed because of the vastly different capital requirements.In 1967 the mining picture is very different. The recent mining developments in Australia are certainly as important as several Bendigos and several Kalgoorlies. The mining industry in Australia has never been more dynamic than today (Table 1). And if we ask why it is so dynamic, the answer lies in the role which overseas capital is playing in the industry. The contribution of overseas capital should concern us not only because we are members of the mining and metallurgical profession, but also because we have a duty to make our profession contribute as much as possible to the well-being of Australians. It is not sufficient to argue that overseas capital is good for the mining industry; we must also examine whether it is good for the economy and the nation. In this context the current criticism of the inflow of overseas capital into Australian mining is useful, for it gives us an opportunity to see what has resulted from the inflow.In discussing this question I do not suggest that we emulate Captain Hancock, that legendary Moonta mine manager who, according to Oswald Pryor's cartoon, used to say to his miners: "When I say a thing is, it is, even if it isn't". The question can only be discussed on a factual basis; and I would submit that many of the important facts relating to overseas capital in our mining industry are often overlooked or ignored. I would further submit, on the basis of these facts, that Australia's present day mining industry has been largely built on overseas capital and that the overall benefits of that capital to Australia have been enormous.

Jan 1, 1967

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By J Shooter

Pezzimenti Laserbore designed, fabricated and commissioned the first microtunnelling machine in Australia in 1986. The System was initially a very basic one, developed in isolation to the overseas explosion in microtunnelling growth headed by Japan and Germany. Market needs in Australia have demanded increasing flexibility in microtunnelling capacity-longer distances, variable ground conditions and larger diameters. The one constant throughout the development process is in maintaining high accuracy û the attribute which most readily differentiates microtunnelling from other limited steering techniques.This paper will highlight the features of microtunnelling by drawing on case studies of completed projects.

Jan 1, 1999

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

By Olson H, Kincaid R

The marine portion of the Pacific Basin and Rim constitutes a significant part of the world's surface in which the mineral resources are virtually undeveloped. Indications of substantial resources have resulted in speculation and uncertainty with regard to their potential in the near term. The main issues are centered on the markets for the resource materials, the technology needs for their recovery, and the possible impacts of their development on the environment. While the governments of Japan, France, the Soviet Union, India, China, and Korea are financing new programs in deep ocean mining, the US is consolidating its early leadership by the continuation of NOAA's authority under the Deep Seabed Hard Mineral Resources Act and the Sea Grant Act, Interior's authority under the outer Continental Shelf Lands Act, and by the development of a new Marine Minerals Technology Center within the Department of Interior's mineral institutes program, managed by the U.S. Bureau of Mines. The Center has a Continental Shelf Division (CSD) located in Mississippi, and an Oceans Basin Division (OBD) located in Hawaii. Research and training in the divisions is directed toward the practical aspects of mineral recovery from the nearshore and deep ocean environments with a strong bias for the OBD toward industrial and international cooperative programs in the Pacific Basin and Rim. In terms of resource development, the marine minerals in the Pacific Basin may be favored in some cases, in competition with land sources, by political and environmental considerations.

Jan 1, 1990

A brief descri;tioki is given of nuclear power reactors and their fuels. These fuels are made from a variety of uranium compounds such as uranium dioxide, and uranium carbide as well as uranium metal and its alloys. The various processes used to produce some of these compounds from yellow cake are outlined. Using the natural uranium, heavy water reactor by way of illustration, fabrication of fuel elements is dis- cussed and the characteristics of U02 powder required for this partic- ular fabrication are indicated. The flowsheets and equipment presently in use overseas for production of this type of U02 powder are described. Possible areas where improvements might be made to this conventional process are enumerated and some details are then given of the programme of work which has commenced at the A.A.E.C. Research Establishment to gain experience in the general field of nuclear grade UO20

Jan 1, 1968

By B Beale

Bow-tie analysis is a commonly used tool to identify and display risks that have the potential for an undesired hazardous event. The output of the analysis are bow-tie diagrams, which are an effective and versatile communication format that can be applied to any type of risk. Contrary to their simplicity, a proper bow-tie diagram that maintains its usefulness and clear communication is difficult to build. Over two decades assisting Major Hazard Facilities with bow-tie analysis for Safety Cases, several common mistakes have been identified. This paper aims to highlight those issues with examples and provide improvement strategies. A sample of the most common mistakes are: - overly complicated risk analysis - poorly scoped and defined terms - poor descriptions and justifications - identifying too many dependent controls. Overly complicated risk analysis leads to wasted time in obtaining data for little gain. The bow-tie diagram is only a model. Effort should be redirected into identifying and managing controls that will make a tangible difference to site risk. Broad scopes lead to enormous and confusing bow-tie diagrams for both the user and the workshop team. Defining the scope of the study, the consequence severity of interest and critical control characteristics creates focused workshops and targeted analysis. With more definitive scope, there may be more bow-tie diagrams, however, they are succinct and specific. Well described causes are imperative for clear communication to users, regulators and future bowtie review workshop groups. It is best to use common wording structures and explain the event stepby- step. Also, clearly document any likelihood calculations and use data references where applicable. Identifying all possible controls creates a false sense of security that there are many layers of protection. In reality, most controls are dependent on a single system or person and could all be compromised from a single failure. A definition of a ‘bow-tie’ control is required whereby it must be independent from other controls. Improving the bow-tie analysis process will assist operators in developing meaningful and ‘operational’ bow-tie diagrams to support risk management systems and practices.

Apr 16, 2024

With the progress of modern mining engineering, one of the features of which is the mining from greater depths and the hoisting of greatly increased loads, it becomes a matter of increasing importance that the engineer should be able to determinewith some degree of precision the character of the strains on the hauling rope. But a wire rope is a complex structure; it is made up of spirally-twisted strands, which in turn are composed of spirally-twisted wires, and it is not particularly easy to say exactly what happens when this "doubly-twisted structure is wound round a drum or over a pulley.. The difficulty has been generally evaded in ordinary practice by the simple device of adopting a large factor of safety for the rope-usually from 8 to 10-a factor which experience has shown is sufficiently large to cover the bending strains set "up when the rope is passed over pulleys of the sizes commonly considered appropriate.When, however, we add the stress due to the bending of the rope to the stress produced by" the direct pull, we find that the actual factor of safety is usually more nearly 4 than 10, and frequently the bending stresses in the rope are so large compared with the simple tensile stresses that their neglect may easily lead to disastrous results when dealing with problems a little out of the common run. Common Empirical Rules.-It is always "recognized that the bending of a wire rope round too small a pulley is likely to do the rope serious injury, but as it is desirable in ordinary winding operations to reduce the inertia of the moving parts to a minimum...

Jan 1, 1907

By Bangerter PJ

The use of gravity concentration is, and has always been, the conventional primary method for gold recovery from alluvial deposits. The development of high capacity cone concentrators and metallurgically efficient wash-waterless spiral separators has had some impact in the technology for alluvial gold processing, but perhaps more significantly has led to the relatively recent use of this gravity concentration technology in grinding circuits of hard rock ore for "coarse" gold removal and for scavenging gold locked in sulphides from cyanidation tailings streams.Gravity concentration systems are relatively low-cost, non-polluting and energy efficient; and their judicial use in gold treatment plants can significantly reduce overall capital and operating costs.The application of modern gravity concentration technology to hard-rock and alluvial gold ore treatment is discussed. Flowsheets and test and operating data from a number of gold processing operations incorporating gravity concentration treatment are presented.

Jan 1, 1984