Search Documents

By W Schauenburg

The increasing problems associated with the disposal of waste and the potential for use of by-products as underground filling material is a subject which is relevant not only to the coal-mining industry. The progressive scarcity of surface disposal facilities for by-products and waste has now become a problem in all sectors - not only for the mining industry. The considerable capacity offered by underground cavities which exists in various mining branches present an extremely promising potential in this context. The backfill process for coal mining developed by DMT in co-operation with Ruhrkohle AG make use of the cavities which are offered by the extraction of coal. It consists of several stages: The fine-grained by-products, such as sludge, filter cakes, fine refuse, ash and flue-gas cleaning residues are processed on the basis of specified formulations in metering, blending and pump facilities on the surface to produce pumpable pastes with precisely defined flow characteristics. On Walsum Colliery of Ruhrkohle AG up to 200 m3/h stowing paste is conveyed into the mine in pipes with diameter of 200 mm (8"). The delivery pressure of the pump operating on surface in conjunction with the hydrostatic pressure of the shaft pipe - amounting in total to as much as 25 MPa - makes it possible to convey the stowing material for a distance 12000 m underground up to the workings without any need for additional booster pumps. Via a pipe installed in the face, the paste is pressurised into the cavities in the specially fragmented rock in the mined-out zone well behind the support. Consistent use of stowage of caved-in goafs makes it possible to reduce surface settlement above the workings. Fires in the stowed rock are either smothered or completely prevented thanks to the exceptional air-tightness in the caved goaf and the cooling effects of the slurry stowage. The reduced danger of fire, the preventation of air-leakage and the positive effects on gas emission from the coal improve safety in the workings.

Jan 1, 1998

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991

By K Marler

The Water Act 2000 includes provisions to manage the take of overland flow water. Overland flow water is water that runs across the land after rainfall either before it enters a watercourse, after it leaves a watercourse as floodwater, or after it rises to the surface naturally from underground. To ensure adequate environmental flows and long-term security for water users, it is necessary to balance the amount of water taken as overland flow water and the amount left to flow into watercourses. A water resource plan made under the Water Act 2000 establishes the basis for the sustainable management of this type of water. Of the water resource plans that have been prepared for Queensland catchments, six include provisions to manage the take of overland flow water. This paper discusses some of the common features of these plans and the management approaches adopted. The paper identifies and explains key aspects of the Water Act 2000 framework for managing the take of overland flow water by the mining industry. In particular it explains key concepts of this framework, such as the ability to take overland flow water using existing works, uses of overland flow water that a water resource plan permits, situations where a specific entitlement under the Water Act 2000 is required, and the means for controlling works that take overland flow water. Future initiatives for the regulation and management of overland flow water are then identified and particular challenges for the mining industry associated with using overland flow water highlighted.

Jan 1, 2006

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Johnson M. W

Factual data about the sedimentation in the Newcastle Coal. Measures are presented. Data concerning the total coal measure sequence (isopachs, sand /shale ratio and total coal thickness variation), data about three coal seams (Borehole, Dudley and Victoria Tunnel) and data about interseam con- glomerate units are discussed. From this data conclusions are drawn about the coal measure environment. The western edge of the coal basin, the Lochinvar Dome, although a high feature was apparently stable during coal measure time. Despite its height it apparently supplied little sediment to the basin. The northern and north-eastern edge, which was unstable, suppl- ied most of the coarse detritus including the conglomerates to the basin. The conglomerates show patterns of fluvial origin but after a period of "normal" variations in pattern they become restricted to two parallel zones evidently tectonically controlled. Deposition of conglomerates is episodic and separated by periods of coal formation when deformation was apparently slight. Formation of each of the three seams considered followed a rather similar pattern - each shows development of thick coal around the basin edge and poor thin coal in the "axial" region of the present synclinal structure. Evidence of in-situ formation of some areas of the seams is discussed and periodic deformation of the basin during coal measure time is postulated.

Jan 1, 1969

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

By A Torpy, N C. Wilson

Improvements in electron optics, field emission gun design, and X-ray detector technology have led to the development of a new class of microanalysis tools. By combining multiple wavelength dispersive (WD) spectrometers, spectral energy dispersive (ED) spectrometers and cathodoluminescence (CL) data sets, a wealth of information can be collected during routine electron beam mapping and analysis. In this paper, data collection on a field emission electron microprobe equipped with five wavelength dispersive, two silicon drift energy dispersive X-ray spectrometers and a wavelength dispersive linear array optical spectrometer has been automated with the optical, electron and X-ray signals being collected in parallel. To analyse the large hyperspectral data sets we have implemented an autoclustering strategy that can be used to produce a quantitative chemical phase map. The cathodoluminescence spectra can be deconvoluted to produce peak intensity maps, which are then converted into elemental speciation images with quantitative sensitivity down to parts per million levels. Both methods are illustrated using typical mineral processing examples, firstly a Ni-laterite sample is investigated with the fine-scale distribution of Ni examined in detail. Secondly, a scheelite sample with rare earth zoning in mapped and rare earth levels quantified.

Jan 1, 2008

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

By Crawford G. R, Wold M. B

The application of the hydraulic fracturing technique to the measurement of in situ rock stress from underground excavation is discussed; including relevant theoretical considerations, equipmenl details, experimental technique and analysis procedures. Examples of the application of the technique at three Australian coal and metalliferous mining operations are given. The results obtained from these applications are compared with corresponding results obtained from overcoring tests conducted in close proximity at each site. Generally good correspondence in a wide variety of rock types is indicated. Experience gained with hydraulic fracturing at several underground mining sites has indicated it to be a quick, cost effective means of gaining an understanding of the in situ stress field in sufficient detail for many mine planning functions.

Jan 1, 1990

By H R. Pein

"The Corridor Sands deposit is situated approximately 190 km north east of Maputo, Mozambique adjacent to the paleo-mouth of the Limpopo River. This deposit is one of the worldÆs largest known economically viable resource of titanium, accounting for approximately one third of the global resource. As part of the pre-feasibility and feasibility study for development of the Corridor Sands project, various geological and geotechnical investigations were undertaken, selected results of which are presented in this paper. These investigations have enabled a detailed understanding of the material characteristics of the orebody as well as the tailings materials, such as the fines, to be developed. These material characteristics have had a significant impact on the selection of the mining and disposal methods currently being implemented."

Jan 1, 2001

Mount Isa Mines Ltd. annually extracts 5.6 million tonnes of copper ore from the 1100 Orebody. All production is by longhole open stoping, with an increasing emphasis on pillar recovery. Drilling and blasting prac- tices have been modified to allow more efficient pillar extraction, with the evolution of a "core and shell" approach. Blast design occurs at the stope design stage, while individual blast preparation is based on detailed ring plans. A programme of blasting research involving surface and under- ground vibration monitoring and fragmentation assessment has been car- ried out in conjunction with production personnel. Drilling and blasting practice in the orebody must continue to evolve with continued research, to suit changing conditions and take advantage of new technology.

Jan 1, 1988

By Drew GJ

Smelting is a process in which heat is applied to ores to produce metals. Impurities are removed by segregation in the slag, or converted to gases or sublimates and discharged up the flues. Mate- rials delivered into the smelter have generally been previously concentrated or processed at the mine, and the size of their particles, and also their chem- ical composition, greatly affect the smelting proc- ess. Some impurities are more difficult to remove than others, and are more objectionable in the finished product. The first metal mine in Australia was opened near Glen Osmond in South Australia in 1841, for silver-lead ore. It was followed by the Kapunda Mine for copper in 1844 and by the very signifi- cant Burra Mine, also for copper, in 1845 (Figure 1). A major part of their ores could not be exported profitably for smelting in England and Wales where the large smelters were then located. In addition to treating ores from Cornwall these also smelted ores from recently opened mines in Cuba, Chile, and Mexico. The Welsh smelting process (Figure 2) was developed over a period of years to utilise Welsh coal to treat copper ores particularly from Corn- wall. The first step consisted of a calcination to remove sufficient sulphur from sulphide ores so that subsequent melting operations would produce copper matte, a copper-iron-sulphide which melted at about 1050¦C. Subsequently refined to white metal with the addition of carbonate and oxide ores when these were available, and often through an intermediate step of blue metal, this matte was finally oxidised to pure copper, or as pure as it could be made in those days. The movement of metal towards greater purity was matched by a reverse flow of slag, carrying reducing quantities of copper, so that the slag rejected from the first melting process carried the minimum quantity of copper. Chemical analysis was virtually unknown. Materials were assayed in the laboratory by a small scale smelting process, and the purity of the final refined copper was judged b} the ease with Mhich it could be hammered into thin sheets.

Jan 1, 1987

Much of New Zealand is comparatively young geologically in the sense that it has only recently been uplifted. In many places young marine sediments are to be found at high altitudes, as evidenced by the existence in the North Island of Pliocene shell limestones which form prominent escarpments at altitudes of about 3000 ft. inthe central part of the Island, and remnants of the same formation found on the summits of the northern Ruahin.e Range at altitudes greater than 4000 ft.

Jan 1, 1962

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second, in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.

Jan 1, 1944

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

Three transient phenomena have been observed and experienced in the operation of large solvent extraction mixer-settlers. These relate to the ability of the settler to discharge streams with low entrainments arising from different phase separation æproblemsÆ. The operation of large-scale laboratory and commercial solvent extraction settlers has been shown by a number of workers to be a dynamic process, especially at the feed end. Circulating flow patterns are common in all three organic, aqueous and emulsion phases. The circulating patterns in deep dispersion bands in long settlers are believed to form roll fronts that can travel down the settler length within the bounds of the dispersion band. Various physical models are proposed to illustrate the formation and movement of roll fronts within the dispersion band. Another transient phenomenon has been observed in commercial settlers operating without any dispersion band. Entrainment of the continuous phase in the advancing dispersed phase is at high and erratic levels. This supports the conventional separation model, which recommends the presence of a significant depth of dispersion band to æfilterÆ the secondary haze from the bulk separated phases. The third transient is the position and shape of the dispersion band within the settler. Large commercial settlers have been shown to exhibit high variability in both these aspects of the dispersion band. The elimination of all three transient phenomena in commercial settlers has been shown to be effective with an in-settler media of coarse size and moderate specific surface area. The effect of the media is two-fold: it dissipates both the circulating flows and the forward velocity of any roll fronts, and creates a stable deep dispersion band at the feed end that serves to trap secondary haze from the primary coalescence process. It is effective in treating both types of transients involving non-existent or excessive dispersion band depths. The media serves to enhance coalescence by providing a static surface of intermediate surface tension on which droplets can collapse. The random nature of the media also provides multiple stream splitting and re-combination, that presents further drop to drop and drop to media impingement, which in turn promotes coalescence.

Jan 1, 2000

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

The problem of spontaneous combustion has long exercised the minds of Mining Engineers. The idea of inertising an area with a non combustible gas has seemed to be an attractive way to overcome the problem. Various agents have been tried but nitrogen has particular attractions and advantages. Britain adopted the idea from the German industry and found that it was particularly suitable for the conditions in British Mines. Over 8 years much development work has been done and specialist equipment has been developed as the requirements came to be better identified with experience. There is a continuing programme of innovation and the technique can be further developed in the future as a means of protecting the very heavy investments which are being made in today's large capacity, heavily capitalised faces.

Jan 1, 1988

By T Jones, K Karunaratna

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is located on the eastern boundary of the Kalgoorlie-Boulder City and is mining an area traditionally known as the Golden Mile. The pit area has been continuously worked since 1893, predominantly by underground mining methods and more recently through open cut mining. There are over 2000 km of old mine headings and numerous stopes under the open pit area. KCGM has interpreted and digitised the underground mine plans and stope sections into a common database. A 2D-model software package, called Pits, was developed in-house and allows old workings to be displayed at any bench level; this is integrated with 3D Vulcan modelling software, which allows triangulated surfaces to be displayed. Almost every mining activity is affected by underground workings. The effective management of the interaction between current mining and the underground workings is very important for safety and production. A specific ævoidÆ management department has been formed and its broad objective is to minimise the impact of underground workings upon production while maximising safety. Special criteria and procedures have been developed and implemented to keep personnel and machinery from being exposed to unsafe ground. It is of primary importance to accurately define the location and outline of underground workings in advance. Probe drilling has been used as the key tool for that purpose. Various geophysical methods have also been trialled on site to detect underground workings; these are discussed in some detail. This paper discusses ævoidÆ management issues such as data integration, void detection and flagging. The impact of underground workings on mine planing, production and slope stability is also discussed.

Jan 1, 2003