Search Documents

Trucks are the primary means of bulk material transport in Open Pit hard rock mines worldwide. They are considered to be the most- flexible system available. The large number of trucks used in some mines provides flexibility. Spare units allow for the reduced availability of the single units. Trucks have however very poor energy efficiency. Only 40% of the consumed energy is for transport of the payload, the remaining energy is required to move the dead load of the trucks. With the increase in cost, pressure, mine operators are now looking for alternative methods to make their operation more economical. Energy conservation and increasing haulage distances and uphill haulage are major factors in many well established operations. New methods have already proven themselves as more economical alternatives. Belt conveyors are an alternative means of transport with much higher energy efficiency. They use up to 80% of the consumed energy for transportation of the payload. Energy costs for conveyors are 30% of the energy costs for trucks on level transport and as little as 15% for elevating payloads. Belt conveyors require much fear spare parts and wear components than trucks. A factor of one to two times applies for level transport and ten to twenty times for uphill transport.

Jan 1, 1986

Three methods of gold analysis are briefly described highlighting some of the problems and advantages of each. The variation of results between samples and splits and due to method preparation are illustrated. The mean percent difference of the fire assay values from the means of sample split values for three cases is 15%. Finally, a comparison of the aqua regia atomic absorption spectroscopy and fire assay fusion AAS techniques is made. This shows that the mean precision, the ability to obtain the same value, of the methods at 98% confidence are +30% and +15% respectively. The fire assay fusion atomic absorption spectroscopy method is relatively more accurate than the aqua regia method.

Jan 1, 1982

With the advent of COAG reforms in the late 1990s requiring full commercial return from æpublic infrastructureÆ, and the tightening regulatory compliance for any project that involves the development or modification of any natural resource, it has become increasingly difficult for the private sector to contemplate development and/or ownership of new large-scale water supply infrastructure. The hurdles that must be overcome often seem insurmountable even before a detailed understanding of the project challenges can be developed. Australia has prospered over the last 50 years in an environment where regional development, including mining, has been encouraged by high commodity prices, a well-trained and available labour force and abundant spare capacity in the necessary infrastructure, in particular rail, power and water. Unless future infrastructure is created in advance of, or closely following, demand, this prosperity may be in jeopardy. This paper presents a snapshot of todayÆs project development challenges, and with reference to some recent case histories, argues that owing to their unique background, culture and status, water utility government owned corporations (GOCs) are well-suited to fulfilling the demand for new water infrastructure.

Jan 1, 2006

By T Ye Koltunova an, L A. Otrozhdyonnova

This paper presents the results of studies on the development of an efficient non-cyanide technology for processing massive, finely disseminated, copper-zinc ores of the Urals deposits. Copper is mainly represented by chalcopyrite and zinc û by sphalerite. The main ore mineral is pyrite, with its content in ores varying from 50 to 80 per cent. At the present time, separation of copper concentrate at the Urals concentrating plants is achieved in a lime medium by non-cyanide technology using sodium sulfide and zinc sulfite as depressors of zinc and iron sulfides and butyl xanthate as the collector. Copper content in copper concentrates amounts to 15 - 17 per cent; considerable losses of zinc are associated with copper concentrate and final tailings. Various collectors were tested during the studies: xanthates and aerofloats with different lengths of hydrocarbon radicals, thionocarbamates, Aerofine 3418A of Cytec Industries, reagent S-703G of Mineral Reagents Int, and modifiers û sulfur dioxide, sodium sulfide and zinc sulfite, with a pH of the medium varying from 5 to 12. Optimum results of copper concentrate separation were achieved in a weakly acidic medium using S-703G as the collector and sulfur dioxide and zinc sulfite as modifiers. The copper content in the copper concentrate was increased by 4.8 per cent. Total copper recovery into the copper concentrate and zinc recovery into the zinc concentrate exceeded five per cent.

Jan 1, 2005

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By H R. Watling, W van Bronswijk

Of the various copper sulfides in the EarthÆs crust, chalcopyrite is by far the most common. This mineral is also the most difficult to leach, with hydrometallurgical extraction processes characterised by prohibitively slow kinetics. While a number of processes, including leaching at atmospheric pressure and temperature, pressure leaching at higher temperature, and bioleaching of concentrates in stirred tanks and whole ores in heaps have been demonstrated to some extent, there is currently no full-scale unit process for the hydrometallurgical extraction of copper from chalcopyrite ores. Titan Resources NL operated a test bacterial heap leach at Radio Hill, Western Australia in 2001, to extract nickel and copper from a mixed sulfide ore that contained significant amounts of chalcopyrite, pentlandite and pyrrhotite. A proprietary mixed bacterial culture was used to inoculate the heap, and the nickel and copper were precipitated from the resultant solution as mixed hydroxides. Although 65 per cent of the copper from the Radio Hill heap was eventually recovered, the rate of extraction followed an unexpected trend, as the initial rates of copper recovery were much slower than column tests had suggested. It was postulated that this was due to dissolved copper precipitating as covellite or chalcocite in the most poorly aerated zones within the heap, ie furthest from the aeration pipes at the base. It was further hypothesised that the lack of oxidants (oxygen, ferric iron) and the likely inactivity of bacteria in these areas limited the re-dissolution of such secondary copper precipitates. In this study the above hypothesis was tested in column experiments using the same mixed sulfide ore and a synthetic leach solution. One set of columns was aerated and another set was operated without aeration. Results showed that precipitation of copper occurred regardless of whether the column was aerated or not. The results suggested that pH of the leach solution played a significant part in the precipitation of the copper. Further column tests revealed this to be the case. These results are described here in detail.

Jan 1, 2004

By Corbett GJ

Magmatic-related low sulphidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar - sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.

Jan 1, 1995

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

By Morandini AF, Occella E, Clerici C, Mancini R

This contribution presents the first results of an experimental research aimed at finding an unified description of the first stages of a rock comminution process. With reference to the case of the jaw crushers and to the specific subject of the comminution law, the tests reviewed and analysed in this contribution have been carried out, at a laboratory scale, on five different materials (limestones, quartzite, serpentinite) at different reduction ratios and feed rates, and accurately recording both total power and idle running power. The analysis of the results has shown that: ò the grain size distribution of the products complies with a modified form of the Rosin-Rammler equation, already found to be well suited to representing the grain size distribution of blasted rock in previous works by the authors; ò observed trends of the consumed power at increasing reduction ratios is steeper than predicted by the classical Rittinger, Kick and Bond laws, Rittinger law representing however a closer approximation of the experimental results; and ò a more accurate description of the experimental results is provided by a modified form of the Rittinger law. Accuracy of the semi-empirical expression has been found to be usually better than ten per cent by comparing actual results with expected Results.

Jan 1, 1993

By Campbell Brown G A

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some millions of tons of rich copper-gold ore, averaging about 45%to 50%silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux were required. Unlimited quantities of cheap limestone were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting Operations started with one furnace in January, 1906, using as flux low-grade sulphide ore from the mine, containing very little silica. When the second furnace was blown in this was supplemented by ironstone from small deposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Kabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required-viz., 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1911

By S Strohmayr, R Harvey, A See

Ernest Henry Mining Pty Ltd started production in August 1997. The Ernest Henry orebody consists of two distinct parts, a complex supergene ore zone overlying a primary ore zone. The economic copper minerals in the supergene ore were chalcocite, bornite, secondary chalcopyrite and native copper while the primary zone has only chalcopyrite. The variability of the supergene zone made concentrator operation difficult and predicting metallurgical performance using mineralogy essential to establish the capabilities of the concentrator. A paper presented at the 1998 Mine to Mill Conference entitled Mineralogy Controlling Metallurgy at Ernest Henry Mining (Barnes, Strohmayr, Brindley and Munro, 1998) presented the testwork and initial plant surveys that showed that the mineralogy of the ore controls the metallurgy of the concentrator. This paper presents the data obtained from the subsequent years of operation treating both the supergene and primary ore types. A review of the actual supergene mineral distribution in feed and subsequent recoveries compared to those predicted as part of the flowsheet design is also presented.

Jan 1, 2003

By C Glassock, P Bodon, M Elias

Computer simulation is a well-accepted tool for modelling the behaviour of large or complex operating systems. Less common is the use of simulation as a design aid, but FluorÆs simulation group regularly applies discrete and continuous simulation models to assist with optimisation and risk management in a wide variety of mining, mineral processing and logistics applications. To demonstrate the wide applicability of simulation modelling as a design aid, this paper describes three case examples from FluorÆs recent work that cover both discrete and continuous operations.

Jan 1, 2003

By Howlett P. F, Courtley S

A problem with secondary breaking at one of the mines of Pasminco Mining led to a study of new rock breaking technologies. Many of the techniques being developed had emerged from the thrust in the USA for continuous drill=break excavation. Such approaches to rock breaking highlighted the applicability of what would normally be classified as tunnelling techniques, to the secondary breaking sector - and possibly the reverse. As a direct result of the investigations for suitable technologies, Pasminco Mining supported the development of two improved rock breaking methods specifically targeting secondary breaking, one of which could be applied to continuous excavation.

Jan 1, 1993

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By Parrington PJ, Bailey A

Serious exploration for carbonate-hosted lead/zinc deposits in the Pillara district commenced in 1971 when Trend Exploration acquired exploration tenements covering stream sediment anomalies in the Limestone Billy Hills area. Shell Minerals managed the project from 1974 to 1976, and BHP Minerals Limited assumed management during 1976. Carbonate-hosted 'Mississippi-Valley- type' Pb-Zn deposits most commonly occur in Palaeozoic shallow marine carbonate complexes. At Pillara upper Devonian (Givetian/Frasnian) reef complexes are preserved on the flanks of Precambrian basement 'highs'. Within platform and atoll facies limestones sphalerite-galena- marcasite-calcite mineralisation occurs as disseminations, veins and breccia matrix, mostly associated with fractures and fault zones. Early exploration concentrated on detailed surface geochemistry and IP geophysical surveys, with geological mapping and shallow target percussion and diamond drilling. Results were discouraging and did not indicate potential for a shallow base metal resource. During 1976-77 BHP adopted a grid diamond drilling exploration technique and commenced testing an area of approximately 50 sq. km, initially using an 800 m square grid. In 1978 high grade mineralisation was intersected in an area subsequently named Blendevale. This was in the seventh diamond drill hole in the 800 m grid drilling programme, and to date more than 400 holes have been cored in the Pillara area. Detailed drilling at Blendevale has defined a number of mineralised breccia zones within an area of 2.4 km x 0.5 km, at depths of 100 m to 600 m below surface. The breccia bodies are associated with a series of north-south trending normal fault zones, forming a graben structure. The mineralisation occurs as breccia matrix surrounding unaltered limestone clasts, as veins filling steep fracture zones, and as

Jan 1, 1986

By A Sinuhaji, H Kalangi, T B. Setyoko

Ore fragmentation at the DOZ block cave mine is highly variable, both as a function of rock type and column height of draw. Initially, the mine was constructed and equipped with limited capability to handle drawpoint oversize material. Significant issues with drawpoint availability and achieving overall mine production targets resulted. A suite of secondary sizing tools was added to the mine equipment fleet over a one-year time frame. Although significant oversize continues to be experienced, use of the correct secondary breakage tool for each particular oversize or hang-up occurrence has resulted in increased drawpoint availability, production rate, draw compliance, and operator safety. Currently, a range of secondary breakage techniques is being utilised to size material for delivery to the primary crusher. Run-of-mine material (3) is directly mucked to ore passes fitted with grizzlys that have one-metre square openings. Ore containing small boulders (>1 m3, 3) is loader-trammed to ore passes fitted with rockbreakers. Medium-sized boulders (>2 m3) accessible from the drawpoint are drilled with Sandvik Tamrock Commando drills. Boulders hung-up within the drawbell are drilled and charged with a Sandvik Tamrock Secondary Breakage Unit. Compacted, fine-grained muck is blasted utilising 55 mm cartridge powder concussion bombs.

Jan 1, 2005

Direct measurements of liquid contents in foams obtained from (x-terpineol a-T) n-pentanol (AmOH) and n-octanol (OctOH) solutions were carried out using a column of special construction. The column enables to determine the liquid contents by cutting-off foam layers of various thicknesses and measuring amounts of liquid contained in the cut-off foam layers. Liquid contents in the whole foam layers, in the top foam layers of thickness 14 ¦ 1 mm and distribution of water alongside foam height were determined. The average liquid contents were high and reached a level of 30, 35 and 40 per cent for foams formed from cc-T, AmOH and OctOH solutions, respectively. The liquid contents in the top foam layers were much smaller. They were of an order of five per cent for a-T and AmOH and 12 per cent for OctOH. On the basis of the liquid distribution alongside foam height some practical conclusions concerning possibilities of minimising amounts of liquid contained in the collected concentrate are presented.

Jan 1, 1993

The application of reinforcement techniques to enhance the stability of underground coal mine roadways subject to high stresses is discussed. Research conducted in the Illawarra Coal Measures has been aimed to delineate the factors which influence the behaviour of rock above roadways and the performance of the reinforcement placed. Design considerations for the reinforcement of mine roadways in the Bulli coal are based on a quantification of the rock response together with a reinforcement strategy to enhance the structural integrity of the roof strata.

Jan 1, 1986

This paper reviews the role of fill in mining including consolidated fill both histor- ically and currently as determined by a recent survey of the Fill Subcommittee of the Canadian Advisory Committee on Rock Mechanics (CACRM). It covers the application of fill in modern min- ing methods including mechanized cut and fill, undercut and fill, post pillar cut and fill and longhole pillar recovery between stabilized fill. An automated fill preparation plant and recent developments in rotary drilling of hydraulic fill conducting holes are described briefly. The paper also summarizes the findings of some of the important laboratory and field work carried out on the behaviour of fill in Canada, the United States and Australia and again draws on current information obtained from the Fill Subcommittee of the CACRM. Space limitations and unavailability of suitable material prohi- bit the summary of similar information from other countries.

Jan 1, 1973