Search Documents

By Kyle J. H, Browner R. E

The selective adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4* and Duolite A-7*, the neutral polymeric adsorbent, Amberlite XAD7*, and the strong base resins, PAZ-8 and IRA-400+ have been studied in both low and high salinity waters, and performance compared with activated carbon. The selectivity of the neutral polymeric adsorbent and activated carbon for gold decreased in highly saline water, while the selectivity of weak and strong base resins for gold increased in highly saline water. This supports the contention that the adsorption mechanism for neutral polymeric adsorbents and activated carbon is the same. Copyright

Jan 1, 1992

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

In his letter of resignation as General Superintendent of the Broken Hill Associated Smelters (BHAS) prior to taking up aconsulting position at imperial Smelting, G.K. Williams wrote that he considered his major contributions at BHAS were:the development of large scale sintering machines;the double tuyere-row blast furnace; continuous lead refining.Despite his well deserved reputation as a scientist, based on his advancement of the metallurgical chemistry underlying lead refining processes, Williams reveals that he considered commercial implementation as the ultimate measure of technological success. Furthermore, he clearly did not differentiate between the scientific and the empirical as a means of achieving that end.

Jan 1, 1985

By X Li, M-F Zhou

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yinachang deposit in south-west China contains large amounts of Fe, Cu and rare earth elements (REEs). Apatite in this deposit records complex REE mineralisation and remobilisation processes.Fe-Cu-(REE) mineralisation at Yinachang occurred at ~1700 Ma, and three stages of alteration and mineralisation are identified: Na-(Fe) alteration, Fe-(REE) mineralisation and Cu-(REE) mineralisation. In the Fe-(REE) mineralisation stage, REE-rich apatite formed together with magnetite. In the Cu-(REE) mineralisation stage, fluids undersaturated with REEs interacted with early-formed REE-rich apatite, during which large proportions of REEs, especially light REEs (LREEs), were leached from apatite.At ~840 Ma, apatite experienced a second interaction with fluid. In that process, REEs were removed from the apatite structure but immediately reprecipitated into new phases within the apatite. Thus, numerous REE mineral inclusions including bastnaesite, monazite and minor Y-phosphate occur in the apatite. There are also a very small portion of LREEs that were transported out of the apatite, resulting in the growth of bastnaesite and monazite grains outside the apatite.This study demonstrates that REEs can be mobilised in multistage hydrothermal activities and highlights the significance of fluid compositions for REE transportation and deposition behaviours in hydrothermal systems.CITATION:Li, X and Zhou, M-F, 2015. Hydrothermal rare earth element mobilisation processes in the Yinachang Fe-Cu-(REE) deposit, south-west China, in Proceedings PACRIM 2015 Congress, pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R Balusu

This paper provides an overview of computational fluid dynamics (CFD) modelling capability developed by CSIRO with the aim of improving the knowledge of flow migration dynamics within longwall goaf areas. The CFD models can be used to study the ingress of oxygen into the goaf in different ventilation scenarios and goaf drainage arrangements. This approach not only helps the design of effective gas control strategies but also the management of spontaneous combustion risk in the goaf. Innovative goaf inertisation strategies have been developed and implemented during longwall sealing operations. Work is continuing to develop general guidelines of proactive goaf inertisation strategies to suppress the development of spontaneous heating behind active longwall faces.

Jan 1, 2005

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

By Y Zha, J L. Walshe, A Ord, N J. Archibald

The purpose of this paper is to discuss the concept of Geodynamic Modelling as an exploration tool and to provide a specific example, namely, the Century Zinc deposit in Northern Queensland. Geodynamic Modelling is an attempt to become more quantitative in the way we develop exploration models. It is a systems approach to ore genesis which examines the complete four-dimensional mineralising system of interest, rather than individual site specific ore deposits. The goal is to establish a predictive capability that enables the explorer to predict grade, tonnage, mineralogy, alteration patterns and precise location of a potential orebody given a particular exploration model. The process consists of two well-defined stages: firstly, a æsoftÆ modelling stage where all available data on lithospheric architecture, geodynamic history, fluid chemistries, fluid flow mechanisms and mechanisms of metal transport and deposition are collected; and secondly, a æhardÆ modelling stage where the system is modelled using fully coupled deformationûfluid flow-thermal transport-chemical reaction computer codes. In the case of the Century Zinc Deposit we point to its existence on the boundary between two fundamental blocks of Proterozoic mantle lithosphere. This boundary has controlled Pb/Zn mineralisation in Northern Australia from the Proterozoic through into the Paleozoic. Detailed thermal, chemical, fluid flow, deformation modelling of the Century System points to an origin involving mixing of crustal oxidised fluids bearing zinc, with reduced fluids bearing H2S and CO2 from the lower crust or mantle. We use this modelling to define critical exploration criteria for another Century type of deposit.

Jan 1, 2000

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

In the early 1950's, it was forecast that there would be, worldwide, a need for approximately sixty computers! Included in that estimate was provision for a considerable amount of geoscience modelling. Since 1950, the role and concept of the computer has changed. With that change has come alteration and adaptation within industry in order to better utilise the services and tools that computers can provide. For example the science of statistics prior to the computer was regarded as an intractible speciality. Computers have allowed the exploitation and further generation of statistical theory. In turn, as the science of statistics has become practical and relevant, the mineral geologist has moved from being essentially "a-numeric" to "non-numeric" to highly skilled in the application and use of very sophisticated statistical concepts. The modern computer provides the opportunity to perform many of the old practices more conveniently and/or economically and, perhaps more importantly, for exploration it provides- an enormous range of activities which previously would have been impossible. Such new activities allow for imaginative and creative application and extension of basic theory into practical situations, which when used by well trained, able people can open up new avenues of exploration. However, the use of such tools by poorly trained or incompetent people can lead to errors potentially as great as any success derived from the same tools. This paper reviews some applications of the computer to exploration, and attempts to discuss likely future developments.

Jan 1, 1987

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By A Gerson, S Miller, R Smart, J Thomas

Environmental Geochemistry International (EGi) and the Ian Wark Research Institute (IWRI) collaborated in a three-year Australian Minerals Industry Research Association (AMIRA) research project (Project Number P387A) focussed on the prediction and kinetic control of acid mine drainage. As part of this project, single addition, and sequential net acid generation (NAG) testing was carried out on sulfide mineral samples. The test samples comprised a range of synthetic waste materials prepared using a quartz bulk and controlled quantities of the commonly occurring sulfide minerals; pyrite (FeS2), pyrrhotite (Fe7S8), arsenopyrite (AsFeS), chalcopyrite (CuFeS2), chalcocite (Cu2S), covellite (CuS), bornite (Cu5FeS4), galena (PbS) and sphalerite (ZnS). NAG test results clearly show that there are significant differences between the acid forming potential of sulfide minerals. The NAG test results for each mineral were compared with theoretical acidity values (NAPP*). The NAPP* calculation was based on stoichiometric oxidation reactions assumed for each of the sulfide minerals. Sequential NAG values for pyrite corresponds closely to predicted NAPP* values, confirming the assumption that pyrite oxidation occurs according to the stoichiometry assumed. For the pyrite sample with 5 wt per cent S, two NAG stages were sufficient for all of the sulfur to be released to solution. Since sulfides in waste materials will generally be dominated by pyrite, results also confirm the validity of including NAG testing for ARD evaluation of most waste rock. NAG testing confirms that of the sulfide minerals examined, only pyrite, pyrrhotite, arsenopyrite and chalcopyrite are acid producing, ie able to produce leachate with a pH less than 4.5. In the case of sphalerite, galena, bornite, chalcocite and covellite the pH of the final NAG solution was greater than 4.5. The significant differences between the acid forming potential of different sulfide minerals could lead to overestimation of acid producing potentials based on NAPP values calculated from total per cent S alone, ie assuming all S is present as pyrite. The oxidation of galena during the NAG test resulted in the consumption of acid. The examination of the galena surface by X-ray photoelectron spectroscopy (XPS) after oxidation in peroxide solution indicated the presence of polysulfide. The reaction of sulfide to polysulfide is acid consuming, thus explaining the net acid consuming behaviour of galena in the NAG test. This reaction pathway may provide a possible explanation for the lower than expected acid production observed for some of the other sulfide minerals examined.

Jan 1, 2003

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

Dry magnet separators are used to upgrade and beneficiate a wide variety of minerals such as hematite and magnetite materials. In recent years advances in dry magnetic separators have improved their performance. Fine particle separation is one of the main areas which still remain weak. This paper will present a new design of fine particle drum separators which used for particle size less than 3 mm. A big problem in processing of iron ore is the grade and recovery of mineral values in the fines fraction. The new design high efficiency drum separator is developed to handle fine feeds. In this drum separators both of the drum shell and magnetic yoke rotate in opposite direction. the results showed that when the material feed size was = 1298 μm, drum shell speed was 42.5 rev/min, magnetic yoke speed was 100 rev/min and the maximum intensity of magnetic field was at = 30° the feed grade increased from 50.87 to 65.67 in concentrate box, increase to 60.45 in middle box and tail grade was 24.44. The total achieved recovery for both concentrate and middle box was 81.89 per cent.

Nov 8, 2021

Current NSW Government policy requires searching for more than just minerals during an exploration program û add endangered fauna and archaeological relics for a start.

Jan 1, 1995

By J C. Furness, F S. Cannon

Metal casting operations are a significant source of hazardous air pollutants. In particular, high production iron foundries emit significant quantities of volatile organic compounds (VOCs) during pouring, cooling and shakeout of iron castings made in green sand molds. End-of-the-pipeline capture and destruction methods to reduce VOC emissions add crippling costs to foundries. Alternately, the incorporation of advanced oxidants (AO) into metal casting green sand systems has been shown to reduce emissions from high production iron foundries in the US, and at the same time reduce operating costs. Cost savings are driven by the benefits of AO in clay recovery systems. Emissions reductions are the direct result of cascading AO-based reactions taking place in green sand molds. This sustainable greening of the metal casting process is a prototype for the development of other AO and non-AO process-based solutions for sustainable high temperature processing of materials. Fundamentals of AO technologies will be discussed along with the performance characteristics of AO processing systems in the metal casting industry and the breadth of other processing and remediation applications for which AO technologies have the potential to be successfully employed.

Jan 1, 2002

By Kelly BJ, Smith GA

The recommendations of a recent American report on "Better contracting for Underground Construction" are considered in relation to Contracting practices on major Australian projects by representatives Of the "classical trilogy" - the Owner, Engineer and Contractor.

Jan 1, 1976

By Falbo A, Barbaro M, Esposito MA, Passariello B

Acidic reductive leaching is one of the best known and most widely employed chemical processes for beneficiating minerals of industrial interest. Conventional acidic leaching with sodium dithionite (Na2S2O4), employed to bleach industrial minerals used in the production of ceramics, glassware, paper etc, does not always allow products of high quality to be obtained. In the work reported here two reducing agents, ascorbic acid and oxalic acid, have been employed in a medium acidified by means of sulphuric acid. Continuous systematic tests have been performed on a kaolin sample containing 0.8 per cent Fe2O3, adopting various operating parameters such as, leaching time, temperature and reagent concentration. In each case the total quantity of bi- and trivalent iron dissolved was ascertained. Removal of 80 per cent and 100 per cent of iron with ascorbic and oxalic acid respectively was obtained, while less than one per cent of iron was dissolved in the presence of sulphuric acid only. Products having a very good degree of whiteness (92 - 94 per cent) were obtained, whereas with sodium dithionite the degree of whiteness was in the 85 to 88 per cent range. The best conditions identified were applied to a sample of quartz for the removal of ferric impurities.

Jan 1, 1993

By Ghiani M, Satta F, Zucca A, Peretti R

After a brief introduction on the principles of contact electrification and a synthetic illustration of the Turbocharger separator, the successful results obtained with different raw materials are given and discussed, with particular reference to a North African run-of-mine with carbonate gangue, a crude ore from India containing pyrite and a mineral sample from Angola having quartzeous gangue. The pre-eminent effect of target surface temperature in the charging device of the separator is emphasised. On the basis of the results of both batch experiments and long-run tests the prospects of industrial application appear very interesting both from the technical and economic points of view, even when compared with froth flotation.

Jan 1, 1993

There has been a significant increase in exploration and development of mineral wealth in South East Asia over the past five years. This paper describes the foreign investment laws in the region as they relate to the mining industry.

Jan 1, 1993

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005