Search Documents

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By E M. Rykaart

The design of soil covers as part of the remediation initiatives for mine waste facilities is common practice and more and more engineers are faced with designing these facilities. The design issues associated with these soil covers are complex and requires a good understanding of unsaturated flow. More engineers are making use of numerical models to predict how cover designs would perform, and this has been necessitated by the high non-linearity associated with solving unsaturated flow problems. There are numerous numerical models available to the prospective users and they are all simplifications of reality using different assumptions. The users of these models often do not understand the limitations of the models but rather select a model based on ease of use, and that lends to increasingly erroneous designs being proposed for construction. This paper describes a comparative evaluation of a cover design using four different codes available today; SoilCover, SWIM, HYDRUS-2D and HELP. The paper does not propose to measure these codes up against each other and make statements about which is better than the other but rather illustrates how the assumptions in each code affect the outcome. The data set used for the comparative study is a well calibrated data set that that has been collected over a long period in time and that has been collected according to strict controls. The authors present the pitfalls of numerical modelling of the surface flux boundary conditions, as well as present guidelines towards appropriate use of these modelling tools.

Jan 1, 2003

By M B. McKevitt, W J. Shaw

The main task of grade control on a daily basis is to define the material that should be mined to a destination under various categories. This can be determined by grade, lithology, quality and blending criteria. In the case of multi-element deposits or deposits with various blending or other processing criteria the optimum selection of ore block boundaries can be quite complex. In every case the balance between ore loss and dilution must be considered when designing the ore block boundaries and this becomes a risk-based decision when using the conditional simulation model. The use of such systems allows grade control to meet specific targets, such as budget tonnages and grades and blended product specifications. Two case studies are presented: the Prominent Hill copper/gold mine and the Rapu Rapu zinc/copper mine. Mining is based on a rational grade control strategy involving a number of factors, including strong geological control, advanced geostatistical approaches, such as conditional simulation, and optimisation of the ore blocking to meet production requirements. This provides an objective, transparent and repeatable grade control strategy.

Jan 1, 2009

Mining is claimed to be unique among industries owing to its dependence on exploration for its existence, the need to operate in remote, inhospitable areas, the vast capital sums required for development, the need to pay royalties regardless of profitabil- ity, the wide swings in prices for many of its products, the finite life of each-mineral deposit, its susceptibility to criticism by environmentalists, its dependence on export markets and sensitivity to' cost and exchange rate fluctuations, the uncertainties inherent in most mining legislation, pressures to grant mineral rights to aboriginal communities and the burden of having to finance its own infrastructure. The special problems of the industry have been recognised in the income tax laws which, generally speaking, allow for the deduction of all capital expenditure before tax is payable. Notable exceptions to this rule are the absence of special deductions for mineral processing facilities and the absence of any deductions for a large part of the expenditure on ports and port towns. The scope and extent of infrastructure expenditure is discussed. The consequences of the burden imposed on the industry include tax inequity, higher capital and operating costs, "high grading" and

Jan 1, 1974

By Y Wan, L Liao

Organo-montmorillonites were synthesised by intercalating different amounts of dodecyl trimethylammonium bromide, cetyl trimethyl- ammonium bromide and stear trimethylammonium bromide into montmorillonite layers, and were used for the adsorption of 17b-estradiol in aqueous solution. The adsorption kinetics and thermodynamic of 17b-estradiol onto organo-montmorillonites and the effect of pH on the adsorption capacity of organo-montmorillonites for 17b-estradiol were studied. The adsorption isotherms at 20¦C, 35¦C and 50¦C were measured. Results show that organo-montmorillonite has a high affinity for 17b-estradiol. More 17b-estradiol can be adsorbed on to organo-montmorillonite and the adsorption is more rapid at a lower temperature. The montmorillonite intercalated with cetyltrimethyl- ammonium bromide with the amount equivalent to one times of its CEC has the highest adsorption capacity. For all organo-montmorillonites synthesised in this study, an optimum pH (around nine) for the adsorption of 17b-estradiol exists. Before this pH 17b-estradiol uptake increased with increasing pH. After that the 17b-estradiol uptake decreased with increasing pH. Simulation of the isotherms indicated that the adsorption of 17b-estradiol onto organo-montmorillonites is a spontaneous and exothermic process. Endocrine-disrupting chemicals (EDCs) are the focus of current environmental concern, as they can cause adverse health effects in an intact organism, or its progeny, subsequent to endocrine function. Most EDCs are man-made organic chemicals (industrial chemicals, crop protection products, antifouling compounds, pharmaceuticals and personal care products). In addition, EDCs can be naturally occurring in the environment (eg the natural female hormones estrone and 17b-estradiol). Therefore EDCs, especially estrone and 17b-estradiol, are ubiquitous in the aquatic environment receiving sewage inputs. Estrogen and 17b-estradiol are among the most potent of all EDCs and are sufficiently stable to survive present sewage treatment processes and are reactivated during those processes through deconjugation (Clara, Strenn and Saracevic, 2004; Zhang and Zhou, 2005; Fukuhara et al, 2006; Butler and Guilbault, 2006; Volpe et al, 2006; Ren et al, 2007; Zeng and Li, 2007). In comparison to traditional contaminants such as pesticides, the concentrations of the most potent EDCs are low, generally within ng/one range. The current sewage treatment processes have limited capacity in removing certain EDCs (eg 17b-estradiol, C18H24O2) It is therefore essential to install additional treatment processes to remove them from wastewater before discharge (Zhang and Zhou, 2005; Fukuhara et al, 2006; Lee, Jung and Kim, 2006). Adsorption is considered to be a possible way to remove EDCs from aqueous solution. Various adsorbents have been studied, including chitin, chitosan, ion-exchange resin, activated sludge, activated carbon (Clara, Strenn and Saracevic, 2004; Yoona and Westerhoffa, 2003; Zhang and Zhou, 2005; Fukuhara et al, 2006; Ren et al, 2007). Studies have shown that organo-montmorillonite has a high affinity for organic pollutants (Li, 1997; Zhu et al, 1998; Han et al, 2001). The aim of this work is to investigate the feasibility of removing 17b-estradiol from aqueous solution by adsorption onto organo-montmorillonite.

Jan 1, 2008

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

It is often said in business that if you donÆt have a customer you donÆt have a business. The same rule applies to project evaluation; if you donÆt have customers you really donÆt have a viable project. It is therefore essential that in the early stages of project evaluation the following fundamental questions are addressed: What products will this project produce? Who are the potential customers? What are the customersÆ requirements with respect to grade and impurities? Do they have adequate capacity to take the production from the proposed project? Will the products introduce adverse effects in the customerÆs process circuits? Will additional waste streams requiring disposal be produced? In the past the attitude has been along the lines of the customer will take whatever we produce at the mine site. Times have now changed with customers now operating under much tighter environmental regulation with waste disposal becoming increasingly difficult. It would therefore be prudent that the principles of product stewardship be used as a tool in project evaluation. This paper will provide a general discussion on customer requirements and provide detail on case studies of the impact of mine products on smelter process circuits. It will provide examples where there were synergies between the mine product and the smelter circuit and where the mine product had adverse impacts on smelter performance.

Jan 1, 2007

Brief summary of results obtained by a French-Japanese cooperative study on the bottom of trenches around Japan. The geophysical prospection, multi beam echo sounding and direct observation with submersible dives of the trench bottom clarified the details of the subduction of oceanic plates. It may be noted, among many new facts found: 1. The subduction and geologic structure resulted from the process is different according to the nature of subducting oceanic plate, and the geology of the land behind the trench. Thus the Nankai trough characterized by the developpement of accretionary prisms is contrasted to that of the Japan Trench where the basement rocks are exposed on the land side cliff of the trench wall. 2. The compressional tectonic situation prevailing in the trench bottom provokes the venting, along the fissures on the bottom, of water contained in sediments. Hydrocarbons contained in the sediments are comming out with water and give nutrients for bacteria. Clams, tube warms, sea slugs and shrimps are taking these bacteria as their food and biological communities with exceptionally dense population for the deep sea of more than 3000 meters in depth are formed on the field of accretionary prism and wall of the land side cliff. 3. An intense compressional tectonic field resulted from the subduction is inducing the transition from the subduction of oceanic plate to the collision of a part of the plate to the continental plate.

Jan 1, 1987

By M Vavro, V Slivka, J èterba

In the course of the last ten years the development of the mining industry in the Czech Republic has been influenced by the pushing through of economic and ecological criteria. Due to this coal mining was ended in the whole series of the underground coal mines. These mines become the source of ecological and safety risks û methane leakage, surface deformation, etc. The way of solving of these problems is by stowing of underground spaces, and also surface fault basins with the help of mixtures produced from industrial wastes. The presupposition of this procedure is knowledge of prescriptions for production of the mixtures, and of the economic advantageousness of carrying out these activities. This contribution pays attention to the utilisation of power-gypsum as a raw material in the production of mining-construction materials.

Jan 1, 2003

I would like to start by thanking The AusIMM and CSIRO for organising this excellent conference and inviting me to give a keynote address. Today I will focus on some broad observations of our industry, and leave the technical discussion to my colleagues who are presenting specific papers covering a wide range of topics. In preparation for this paper, I did a little research into the early history of the Pilbara iron ore industry. I was fascinated to read a quote attributed to Harry P Woodward, the Government Geologist in the late 19th century, before Federation. Mr Woodward described the Pilbara as an iron ore country and observed that æthere is enough to supply the whole world should the present sources be worked outÆ. Mr WoodwardÆs prediction could be viewed as wishful thinking and certainly at Hamersley Iron I would gladly envisage the Pilbara supplying the worldÆs entire iron ore needs! In reality, Western Australia accounted for 162 million tonnes or 36 per cent of seaborne trade in 2001. An impressive effort, but not quite the total world supply as Mr Woodward imagined. But we shouldnÆt dismiss these historical musings out of hand û perhaps we could see it as a challenge for the industry to æwork outÆ the present sources. We all know there is abundant iron ore in the Pilbara, and I expect it is only a matter of time until our collective technical expertise and sheer hard work will enable us to utilise its greater range of ore types. Opening up new markets will be a key pathway to creating additional value from the Pilbara ores. Today I will examine the state of play of our industry and the major influences that shape our business at present, before considering what the future might hold for us. I canÆt guarantee the accuracy of my crystal ball, but the stability and long-term nature of our industry does enable some reasonable hypotheses on where we are heading. I will also spend some time examining the way in which the iron ore producers are working to maximise the value of their resource base and obtain more from their existing capital assets.

Jan 1, 2002

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Thompson IR, Solomons SS

Underground mining with the cut and fill method has been declining during the past decade or so, being replaced mostly by sublevel open stoping methods. During 1983 the Australian Mineral Industries Research Association Ltd. (AMIRA) commissioned a review of the method, with the aim of compiling the state-of-the-art, indicating future trends and recommending topics for research that would be needed to support this future mining. Mines using the cut and fill method in Australia and three other countries were visited to compile current practices and expected developments.Cut and fill is mostly used where geological and ground conditions are unsuitable for open or caving methods. These range from narrow, irregular orebodies to wide, massive orebodies where pillars are retained in ore. There is significant potential for improvement and further development of the method. It may then be used in a broader range of conditions and for orebodies that may not otherwise be viable to mine.

Jan 1, 1985

By Kruse JW, Kjar AR

Recently there has been increased recognition o'f the cost savings that can be achieved by the greater use of offsite preassembly for the construction of industrial plants. Preassembly is a method of construction which involves considerable offsite assembly of complete sections of an industrial plant in established fabrication shops. The preassemblies are transported to the plant site, often by large and oversize transport systems where they are set on prepared foundations, finished and interconnected to other sections of the plant as required. The concept of preassembly is not new, but widespread interest has been shown because site construction costs in all parts of the world have increased rapidly and often at a greater rate than in established fabrication areas. Particular interest has be focused on remote, isolated and inhospitable plant site locations. These areas require the import of skilled labour, the payment of high labour rate premiums and the development of infrastructure to support the workforce for the duration of the construction period.

Jan 1, 1983

Zinc concentrates from the newer mines and from proposed developments provide both opportunities and processing challenges to the conventional roast-leach electrowin smelters. These concentrates are often characterised by low iron, elevated silica, possibly high manganese, and levels of elements such as germanium which may cause concern. In addition, environmental constraints on residue disposal are forcing significant changes to some smelter practices. Iron in concentrate, and the resulting environmental impact of residue disposal are now major questions. However, normal concentrate tariff structure provides a disincentive against smelters taking high grade concentrate and oxide fume. Processing technology to cope with these changes is reviewed, as is de-watering and materials handling of ultra-fine concentrate. Within a few years, such fine concentrates will account for up to 1 000 000 t/y of contained zinc. New processing technologies including novel transport methods, siliceous leach circuits, manganese removal cells and front-end smelting will become significant in zinc smelting.

Jan 1, 1993

By P O. Andersson

Mining of sill pillars is more difficult than the ordinary mining. The sill pillar mining is performed under more difficult conditions and the mining of the sill pillar itself produces more problems; failure of the rock due to high stresses, difficulties in controlling the fill above, overall stability of the stope and special requirements on the technique for backfilling. Altogether this makes sill pillar mining technically difficult and often not profitable. A project was therefore initiated with the aim to increase the mineable ore reserve by making sill pillars mineable, both technically and economically. The project aimed at developing technique for already existing sill pillars as well as planned sill pillars. For the existing sill pillars a technique would have to be developed for mining beneath unstabilised fill. For sill pillars that would be created in the future, the most suitable mining method and methods of supporting or stabilising the fill in the stope above was to be chosen within the project.

Jan 1, 1998

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Pan

This case study assesses the application of Mine-to-Mill optimisation combined with Whittle Consulting’s Prober<sup>®</sup> economic optimisation for the purpose of economic value uplift in open cut base and precious metal operations. The study extends the application of these optimisation methods to incorporate the recent practice of Ultra High Intensity Blasting (UHIB) developed by Orica Mining Services. The case study deposit known as “Marvin” is a copper/gold porphyry resource that is commonly used in optimisation software training and industry case studies. It has many similarities to Newcrest’s Cadia Hill open pit mine in NSW. Prior desktop research and industrial trials employed static assessments of Mine-to-Mill effects. No prior work other than a Whittle Consulting client study, has sought to assess the impact of variable fragmentation on enterprise economic value. This study examines the use of variable blasting intensity as a driver of economic value maximisation over the mine’s life.CITATION: Howe, S and Pan, J, 2018. Application of enterprise optimisation considering ultra high intensity blasting, in Proceedings Complex Orebodies Conference 2018, pp 14–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011