Search Documents

By Kerr M. H, Slaughter P. J

Design of the new cemented hydraulic fill plant was based mainly on experience with a succession of previous fill plants. Two stage cycloning of combined concentrator tailings was introduced. Design of the two stage cyclone configuration was assisted by computer simulation of cyclone performance. Cementing additives, namely Portland cement and ground copper reverberatory furnace slag, drawn from bulk storage, are pre-slurried prior to mixing with hydraulic fill. Quality control of fill being sent under- ground is achieved by a series of automatic control loops. Plant instrumentation was given prime consideration during the design phase. Inventory checks of all mass flow metering equipment are made at regular intervals. Fill is pumped to boreholes at several locations. Details of the equipment and operating procedures for the plant are Discussed.

Jan 1, 1973

By J Player, R de Vries, E Villaescusa, R Hassell

Concerns regarding the uncertainty of stope dilution at MMG Dugald River Underground Mine led to a trial stoping program to acquire full-scale comprehensive geotechnical information and to test the validity of the geotechnical and mining parameters. Given that stope production drilling and blasting is a key parameter that influences dilution a detailed stope blast vibration project was implemented. The stoping trial consisted of 19 stopes, a combination of both sublevel open stoping and longitudinal and transverse stopes, of which five were monitored for blast vibrations.The blast vibration project utilised 20 triaxial geophones and five triaxial accelerometers installed in the hanging wall of five monitored stopes. For each stope fired, full blast waveforms were recorded along with detailed information of the blast design. Analysis of the blast vibrations used the Holmberg-Persson approach, with potential damage determined by the relative (Holmberg-Persson) K values.The project identified the benefit of parallel, breakthrough slot holes in reducing blast vibration damage. The results show that radial rings toeing or stabbing into the stope wall lead to higher vibrational energy yield which contributed to increased overbreak. Hanging wall overbreak, by comparison, with parallel, breakthrough blastholes with 1 m standoff, combined with lower density explosive charging (0.8 EP) and increased delays limited blast vibration damage. A number of ring burdens from 1.4 m to 2.5 m were monitored with no difference in terms of energy yield being identified. Changes to the stope drill and blast design are suggested to better control the large blast vibrations and recommendations from this project have been implemented into future mine design and planning.CITATION:Hassell, R, Villaescusa, E, de Vries, R and Player, J, 2015. Stope blast vibration analysis at Dugald River Underground Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 221–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

By B Taylor, S Evans

Bulk explosive technology for underground mining has not seen any significant technological advances since the widespread transition from ammonium nitrate fuel oil (ANFO) to ammonium nitrate emulsions (ANE) commencing in the 1980s. The in-hole energy profile that conventional ANE systems deliver is limited by the physics of chemical gassing and simple control systems. This compromises the range, precision, and accuracy of energy delivery into the blasthole, and in some cases limits the length of charge that can be delivered. Orica’s 4D™ bulk system removes many of these constraints, enabling better blasting performance across all underground mining methods. This paper reviews work completed at three mining operations across Australia, the United States, and Chile with a focus on how this system can improve mining operations and deliver sustained commercial and productivity benefits into the future. These benefits include improved ore recovery, reduced dilution from waste rock, and reduced overall explosives consumption. This paper also reviews how this new technology can be applied for planning future mining operations.

Sep 1, 2024

By R Berry, J Hunt, T Kojovic

Geometallurgy aids the understanding of orebody variability through the integration of geological and processing information, thereby enabling spatial mapping of processing (eg comminution or separation) performance across a deposit. In order to do this, estimates of quantitative geometallurgical attributes are needed so that continuous downhole profiles can be generated for each attribute, providing vital data for the development of processing domains through geostatistical modelling. However, as traditional comminution tests are high cost and/or require large samples, current practice typically results in insufficient data density and distribution of comminution indices making it difficult to model and map deposit scale variability. The aim of this work was to find a method to estimate comminution indices based on data that is widely available at mine sites. This data includes mineralogy and chemistry of drill core samples, plus logging information such as lithology and alteration. Work to date indicates that comminution parameters such as semi-autogenous grinding (SAG) Power Index (SPI), Bond Work Index (BWI) and A*b (Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight test (DWT) Index) can be modelled using chemical and/or mineralogical data. The estimated hardness indices can then be propagated into the mine site database and used in the definition of processing domains that map inherent variability across a deposit. The estimates can thus provide geometallurgical inputs for spatial modelling, mine planning and optimisation initiatives.CITATION:Hunt, J, Kojovic, T and Berry, R, 2013. Estimating comminution indices from ore mineralogy, chemistry and drill core logging, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Braes J. R, Neale J. R

The New Broken Hill Consolidated Limited (NBHC) mine currently produces 1.42 million tonnes of silver, lead and zinc ore annually. All of this ore is treated by the NBHC milling ccx[plex. This paper describes the crushing, grinding, flotation and filtration circuits used in the treatment of this ore and lists the major items of equignent used in these circuits. Metallurgical results, manning levels and consumption rates of reagents and grinding media are shown.

Jan 1, 1983

By S S. Kanchibotla, D La Rosa, R W. Pesch

The Porgera Joint Venture and Dyno Nobel have commissioned a joint project to optimise the drill and blast operations to increase the overall profitability of the mine. One of the aims of this project is to increase the throughput of semi autogenous (SAG) mills by optimising the blast fragmentation. A number of test blasts were conducted during the period May 2000 to January 2002 and the ore from these blasts was campaigned through the mill. The data from these trials suggested up to 15 per cent increase in the SAG mill throughput with high energy blast designs. However, changes in ore geology (shape, structure and hardness) and potential ore dilution/loss and wall damage have raised concerns about the economic benefits of these designs over the entire orebody. The lack of a system to track the economic benefits of these modified designs has also compounded these concerns. PJV and DynoConsult, the consulting arm of Dyno Nobel have initiated steps to minimise the potential for ore dilution and wall damage resulting from these modified designs. DynoConsult worked with Julius Kruttschnitt Mineral Research Centre (JKMRC) to develop and implement a blast management system to track the quality of blast implementation and down stream process benefits. This paper discusses the implementation of the system and the results achieved to date.

Jan 1, 2003

By Ypma PJM

The Westmoreland uranium deposits occur on the northern flank of the Murphy Tectonic Ridge in the upper member of the Westmoreland Conglom- erate. Uranium mineralization is spatially associated with the contact of the overlying basaltic Siegal Volcanics and the margins of in- trusive dolerite dykes which are geochemically similar to the Siegal Volcanics. Thermoluminescence (TL) measurements on 800 samples from within the orebodies and surr- ounding host rock (up to 8 kilometres away from the deposits) have indicated that all of the Westmoreland Conglomerate has suffered major radiation damagg attributable to at least 10 ppm uranium over 10 years. The underlying rhyolitic Mid Proterozoic Cliffdale Volcanics have distinctive TL glow curves indicative of radiation sensitization caused by high uranium contents. These vol- canics are part of the Mid Proterozoic volcanic event known to be enriched in uranium. The Westmoreland Conglomerate has been derived by erosion of the uranium-rich Cliffdale Volcanics and associated Nicholson Granite Complex which makes it likely that the Westmoreland Conglom- erate had a high inherent uranium content.

Jan 1, 1984

Mine dewatering has long been a problem with mines and some of the shallowest mines have the biggest problems. Machinery was developed by the ancients for raising water by rope buckets with treadmills or by horse whim. From the 1700's on into the early part of this century, massive cornish pumps or equivalent were the vogue powered by steam. One Australian mine pumping system was claimed to be the largest in the world just after the turn of the century. It was installed at Beaconsfield in Tasmania and the mine, like so many other mines of the period, were beaten by problems and cost associated with mine dewatering. The owners of that mine are looking at the feasibility of dewatering using surface drilled wells. Much simpler and smaller pumps are the order now and it is feasible to use boreholes instead of shafts to contain the pumps or else to use the holes to convey discharge waters to the surface from pumps located in drives or stopes.

Jan 1, 1988

By Q Zhou, G Barrett, Y Choi, J Jiang

As part of a general review of processing double refractory ores through Barrick GoldÆs autoclaves /carbon-in-leach (CIL) facility at Goldstrike, a study was made to evaluate the use of surfactants for reducing the loss of gold during cyanide leaching of preg-robbing gold ores. Consistent improvement of gold recovery was observed with surfactants at various testing conditions. This paper will discuss the results obtained from laboratory and pilot-scale testing, as well as, review potential mechanisms for the observed improvement in gold recovery.CITATION:Zhou, Q, Barrett, G, Jiang, J and Choi, Y, 2013. Surfactants for gold recovery improvement with preg-robbing gold ores, in Proceedings World Gold 2013 , pp 367-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J Arola, B Kettunen, W M. Bond

Separation of fine and coarse particles as separate streams prior to flotation, and their differential treatments, could substantially increase recovery and reduce collector consumption. A series of simulations was carried out to quantify the benefits from plant scale implementation of such a treatment at the Ispat Inland flotation circuit (Minorca mine). The study involved detailed plant sampling and sample analysis to generate the data needed for simulation studies. Samples were taken from all the streams from flotation feed to final concentrate, as well as cell lips and cell pulp. Sampling was repeated for the second ore blend that was processed by the plant during different periods of a year. Sample analysis involved sieve analysis and size by size chemical analysis for total iron, magnetic iron and silica. Raw data were mass balanced, and flow rates within the circuit were calculated. Mass balanced data were used to calculate model parameters representing the existing conditions. Usim Pac was used for both mass balancing and simulation studies. Available pilot and bench scale data were utilised to define the modified flow sheet and expected performance. The simulated flow sheet included classification of flotation circuit feed by hydrocyclones. While the coarse fraction followed the existing flow sheet, the fine fraction was sent to a magnetic separator. Magnetic and rougher flotation concentrates were combined to form the final concentrate. Two simulations for each blend were carried out. The first one assumed that there would be no change in size by size kinetic behaviours of both gangue and magnetite due to this modification. This was named as the worst case scenario, in which particles had a longer residence time due to reduced flow rates within the flotation cells. The second scenario anticipated that there would be an increase in recoveries of gangue and magnetite going into froth launder due to more efficient use of collector in absence of fines. Results showed that pre-classification of flotation feed could improve the flotation recovery by 0.3 - 0.5 per cent, with the major benefit being significant reduction (40 - 60 per cent) in the amount of collector used.

Jan 1, 2005

Lime is the common reagent used for pH control in cyanide gold circuits. Lime can be supplied as either quicklime (CaO) or 'hydrated lime(Ca(OH)2). Both are dry powders with variable flow properties. These properties demand special attention when designing machin- ery to handle them.

Jan 1, 1987

By Y Peng, D Wannas

In the fine particle flotation technologies being developed today the fine hydrophilic (gangue) particles are usually well dispersed. These highly dispersed fine particles can be recovered into the flotation froth product by mechanical entrainment. Flocculation of hydrophilic particles caused by polymer depressants could potentially reduce the mechanical entrainment of these particles. This paper reports testwork completed on fine particles of several solids, iron oxide, hydroxylapatite, galena and sphalerite, as well as on a relatively coarse quartz sample (-75+38 ¦m). Dodecylamine was used as a collector for the quartz, and several dispersants and polymer depressants, including sodium silicate, sodium metaphosphate, zinc sulfate, potassium dichromate, corn starch, corn dextrin and carboxymethyl celluloses (with molecular weights of both 700 000 and 80 000) were used as flotation modifiers. The major part of the testwork involved flotation tests in a 200 ml flotation column. Both water and solid recoveries were recorded. The degree of flocculation and dispersion was determined by settling tests in 250 ml graduated cylinders. It was observed that flocculation of the fine hydrophilic particles significantly reduced their mechanical entrainment, while dispersion severely aggravated it. Thus, in the flotation separation of artificial mixtures of the -75+38 ¦m quartz and fine iron oxide or hydroxylapatite, polymer depressants that caused flocculation were found to perform better than the ones that did not cause flocculation.

Jan 1, 2005

By R Varden

This paper summarises the process taken to simplify 35 ground support standards accounting for the multiple development profiles, dynamic geotechnical environment and the practical safety implications of a large-scale change in the ground control standards. This reduction was required after an incident involving incorrect standards being issued. The subsequent investigation identified that: • Selection of ground support standard for a mining instruction (MI) is not straightforward due to multiple standards, standards not reflecting current reinforcement used and complex geotechnical environment being encountered. Instead, site-specific ground control instructions were being issued. • Ground support standards were hard to follow and confusing, errors were present and not all standards to scale. • Ground support standards being used did not reflect what was being installed, ie bolt type incorrect and mesh orientation different. • No process or tier action response plan (TARP) for operators to follow for ground control standard noncompliance. • No justification for ground support standards being used in the current geotechnical environment. • No process for ground support standard selection and thereby no paper trail to document and assess adequacy of performance. A project was undertaken to reduce and simplify the ground support standards, produce a justification document to support ground support design and develop a process for site practitioners to identify the type of ground support standard required for the mining instruction. The exercise of rationalising the ground support was met with some challenges, including: • Technical aspects to determine the level of demand and the capacity for each ground support scheme. • Training the geotechnical engineers how to determine the level of risk for each area. • Winning over other technical services staff and the underground mining contractor of the new approach and then implementation. One of the major successes was the acceptance by the underground operators who found the system simplified their work and gave them increased confidence in management of seismicity. The rationalised ground support standards have now been successfully in place for over two years.

Mar 29, 2023

By J Li, H Hooi, D Payne

Caval Ridge Mine (CVM) is one of the newly established open-cut coal mines of BHP in Queensland, where no tailings dam is planned to be built in order to minimise environmental impacts from mining activities. The waste streams from the Coal Handling and Processing Plant, including fine tailings dewatered by belt filter presses, coarse rejects, and mixed plant rejects, are co-disposed within waste dumps built with pre-strip and dragline spoils. Due to high rejects output (35 – 60% of feed) and low spoil to reject ratio (< 5) the large quantities of rejects bring significant geotechnical and operational challenges to CVM, which are exacerbated by increasing annual production rates and additional rejects from washing coal from an adjacent mine. Further in-house geotechnical review commenced in mid-2014 based on the initial geotechnical studies during the project stage of CVM between 2011 and 2013. The outcomes have enabled rejects disposal at CVM by constructing large belt filtered tailings cells, coarse rejects only dumps, and co-disposal of the mixed plant rejects at dump tip-heads. This paper presents the rejects disposal strategies at CVM from both technical and operational aspects. It also discusses future projects for belt filtered tailings moisture reduction including assessment of tailings clay mineralogy, as well as mixed plant reject co-disposal verification and optimisation.CITATION:Li, J, Payne, D and Hooi, H, 2018. Plant rejects disposal strategies applied at Caval Ridge open cut coal mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 50–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

As mining and extraction processes improve and lower grade ores become economic, mining for most ores have extended to depths beneath the zone of weathering oxidation created over geological history. These deeper openings expose sulphidic formations and reduced mineral species as either primary ore or simply as accessory or gangue minerals in the country rock. This is not new, underground mining for primary base metal and gold have long been familiar with these problems, as have coal and uranium miners. The change is simply that the number of mines exposing sulphidic waste rocks, tailings to the atmosphere and/or leaving behind dewatered sulphidic rock surrounding the mine void has increased the number of sites from where acid mine drainage (AMD) may emanate with consequential problems for the hydrological environment including downstream catchments (Miller et al, 1996). The principles of ecologically sustainable development (Brundtland, 1987) have been more or less ratified by all the developed nations of the world and this has led, amongst other things, to an expansion unprecedented in the research and documentation of means for achieving long-term environmentally acceptable stabilisation of solid wastes of all sorts. These have revealed that AMD problems can be minimised and even reversed in many cases by the integration or co-disposal of biodegradable organic wastes with oxidising sulphidic wastes (Elliott et al, 1996). This paper considers how this might be achieved at mine sites in Australia and the results encountered at some relevant sites.

Jan 1, 1997

This paper deals with the evolution of Canadian shaft sinking technology over the last 15 years. Most, if not all, shaft excavation projects in Canada prior to 1990 were sunk using traditional benching methods with labour intensive equipment. In the late-1980s, J S Redpath Limited of North Bay, Ontario, Canada, were contracted to deepen the shaft at Atomic Energy of Canada LimitedÆs Underground Research Laboratory (URL) located in southern Manitoba. The laboratoryÆs role was underground hydrological and geomechanical research, so the project offered both time and opportunity to conduct additional experiments while sinking. The offshoot of the research program was the true birth of the Canadian version of full-face, long round shaft sinking technology. Throughout the 1990s, this sinking method has been further refined over a number of shafts. The results have been faster sinking rates, a safer work environment and an overall improvement in project economics.

Jan 1, 2002

By Barnes E. L S

With the introduction of diesel powered loading and hauling equipment, a number of Australian mines producing less than one million tonnes per year from shallow orebodies have been dev- eloped by decline. This method of entry has the advantage of providing both flexible access and early prod uction. However, as the depth of mining increases so does the operating cost of haulage, due to the need for more trucks. This cost, together with increased capital requirements for both equipment and infrastructure, leads to the point where the alternat- ive of shaft hoisting must be con- sidered. With an established decline it is possible to provide an ore hoisting shaft using a drilled raise with subsequent stripping to a suitable size. Using DCF techniques and known equipment operating and capital costs, an economic comparison of the two systems is made to determine the limit- ing depth to which truck haulage can be used.

Jan 1, 1973

The port of Townsville is situated on the main north/south rail system of the Queens- land Government Railways and is the eastern terminus of the east/west rail link from Towns- ville to Mount Isa. With a stable beef and wool producing area along the east/west rail route, the expanding mineral industry development at its western end and the continuing growth of the Townsville region the administrators of the port are continually'keeping abreast and ahead of port development to ensure an effective and economic growth of port facilities to meet the needs of the area served by Townsville.

Jan 1, 1974