Search Documents

The developments in hydrocyclone classification in the milling circuit at Bougainville Copper Limited are discussed. A major change in cyclone size and improve- ments in operating conditions have been made. Test work has been carried out to assess the classification performance of a modified Linatex cyclone, Wemco cyclones and a two stage cycloning circuit. The use of a scalping cyclone, to remove coarse material from the present overflow product for regrind, has also been investigated.

Jan 1, 1978

By D Thornton, R Hodson, D Sprott

Blast fragmentation size distribution and thus blast design have been found to have a direct impact on the load and haul cycle through excavator dig time and bucket payload. Previous studies have demonstrated that by reducing the excavator dig time and increasing bucket payload, significant improvements can be made in both productivity and unit cost. Simulation work reported in the literature indicates that a 20 per cent improvement in dig time may result in only a three per cent improvement in load and haul productivity and unit cost. At the same time, a ten per cent improvement in bucket payload will directly translate to a ten per cent improvement in load and haul productivity and unit cost. Based upon these findings, extensive laboratory and field work have been undertaken in the past to correlate blast fragmentation distribution to bucket payload. In contrast, the literature reports limited studies quantifying the impact of blast fragmentation on excavator dig time. Field work was conducted at Placer Dome Asia PacificÆs Granny Smith Mine (Wallaby Pit) in Western Australia, concentrating on quantifying the impact of blast fragmentation on the dig time of a Liebherr 994 hydraulic excavator (shovel attachment with 14 m3 bucket). Fragmentation was assessed for each truck load of material using the Split Desktop system, while the excavator cycle analysis was conducted manually. Measured fragmentation P80 (fragment size at which 80 per cent of material passes) values ranged from 200 mm to 1200 mm. The field study investigated the impact of various fragmentation parameters (P20, P50, P80, cumulative per cent passing 250 mm size fraction, and uniformity index) on the average and total dig times. The results indicate that the fragmentation P80 provides the best correlation to average dig time (total dig time divided by the number of bucket passes to load a truck). The total dig time was found to be dependant upon the fragmentation P80 and the number of bucket passes to fill a truck. Monte Carlo simulation results, based upon these relationships, indicate a 26 per cent improvement in average dig time and a 12 per cent to 46 per cent improvement in total dig time (bucket passes ranging from 4 to 8), with a change in fragmentation P80 from 600 mm to 200 mm.

Jan 1, 2003

Copper was first produced in Australia in 1844, at the Kapunda Mine in South Australia, and, by 18i>0, production exceeded 2,000 tons of copper a year. Output increased ,steadily, reaching a peak of 14,00Qo tons a year in 1867 and 1868, when the Burra Burra and Kapunda Mines in South Australia and the Peak Downs Moine at Clermont, Queensland, were at the height of their production. At this period, Australian copper formed a considerable percentage of the world's supply, its output equalling, for a short time, that of the United States. Production declined to between 3,000 and 4,000 tons a year after the closing of' these three mines between 18717 and 1879, and, at this stage, the Australian output came chiefly from the Wallatoo and Moonta mines in South Australia. About 19000, it began to rise again, with the extension of the railway to the copper fields of Chillagoe and Cloncurry, and, between 1905 and 1912, was at its greatest, with a maximum of 47,774 tons of copper in 1912. During this period, Australia contributed 4,7 per cent. of the world's annual production, and ranked among the six major copper-producing countries of the world (Table 1).

Jan 1, 1943

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By Waterhouse J. D, Harris B. M

This paper briefly describes the construction in 1979/80 of a 70m deep trial open pit coal mine near Bowmans S.A. and describes more fully the hydrogeological aspects of the exercise. The primary purpose of the Trial Pit was to provide a large sample (700 tonnes) of coal for combustion tests to be carried out in West Germany and the United States of America. Consideration was given to obtaining the sample of coal by drilling and by shaft sinking as alternatives to open pit methods. It was expected that economic mining of the deposit on an operational scale could only be achieved by open cut methods and it was recognised that major uncertainties existed in planning such a mine in the deep unconsolidated multi-aquifer deposit. It was therefore elected to obtain the bulk sample by constructing a trial open pit, which would be closely monitored to provide as much data as possible for future planning of a full scale mine. The dewatering of the Trial Pit was achieved using 26 deep pumping wells, assisted in the later stages by several hundred well points. This was probably the largest dewatering project currently in operation in Australia.

Jan 1, 1981

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

As the gold price, and consequently ore reserves, improved in the late 1970's, a programme of upgrading the gold recovery circuit at the Phoenix treatment plant at Central Norseman was initiated. The introduction of oxidised ore with a high clay content from the North Royal open cut caused a reduction in thickening and filtering capacities, which in turn restricted plant throughput and increased gold losses in the residue solutions. Test work into alternative washing facilities showed that the installation of a five stage counter current decantation system would restore throughput and reduce soluble gold losses. Installation of the system achieved the objectives of increased plant tonnage, increased proportions of the high grade oxidised ore in the mill feed and decreased gold losses in the residue waters.

Jan 1, 1978

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

In the years prior to the outbreak of war in 1939 Australia's production of copper had declined from a peak of about 80,000 tons in 1911-1915 to approximately 25,000 tons in 1939. This production met the need of the slowly growing national requirement and gave an excess for export. However, with the intensification of the war effort in 1942 due to the imminence of a Japanese invasion of this country, or at least a blockade of the sea lanes, it became necessary to expand production of armaments, and consequently the demand for copper increased beyond the capacity of the industry. Importation of copper to Australia during the period 1940-1944 was 131,000 tons.When exploration of the Mount Isa orebody was first being carried out in 1928, No. ID diamond drill disclosed the presence of some copper ore lying outside the limits of the Black Star orebody2, but it was not until 1941-1942 that the development of No. 7 level in the Black Star orebody enabled the existence of a lode of copper ore of economic grade to be established. At the request of the Commonwealth Government of the day a programme of development for copper production was undertaken whilst lead smelting was continued as before the war.A series of flotation tests on up to 1,500 tons of ore at a time, was undertaken and the concentrate so obtained was stockpiled. These tests were conducted, using one section of the lead mill, and demonstrated that a concentrate grade of 22-23% Cu with a recovery of 80-85% might be expected.These recovery figures were afterwards much improved, and 93-95%was obtained before the close of smelting in 1946.

Jan 1, 1953

By M Brooks, M Nelson

A fundamental study was carried out on super pit sulphidic gold ore to establish the most influential flotation characteristics which were subsequently used in the development of an optimum flowsheet to achieve best economical recovery of gold. In developing the flowsheet, consideration was given to existing operational constraints in the treatment of the Super Pit ore. The fundamental study also included an innovative diagnostic investigation to establish the location and value of gold in the major mineral assembly of the super pit ore from a metallurgical rather than a mineralogical perspective. This study mapped a metallurgical fingerprint of the major types of super pit ore in relation to the location and association of gold.

Jan 1, 2000

By Grace NC, Lightfoot BW

Small scale trials of the smelting of a copper concentrate in the Sirosmelt submerged lance reactor are described. Pellets of concentrate were dropped into the reactor while injecting air-rich mixtures of oil and air through a lance into a bath of matte overlain by slag. This produced a discardable slag and a matte which was converted in sequential stages in the same reactor to white metal and blister copper. Difficulties were encountered in determining the end points of the converting stages but control techniques were developed to allow successful operations producing blister copper. Deportments of minor constituents of the concentrate to slag, matte,metal and fume for the three stages are reported and possible applications are Discussed.

Jan 1, 1980

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

Life inside the mining family was regulated by the mine. The whistle shrieked the change of shift to the Cornish, Welsh and German miners digging the alien soil for copper at Burra in the 1840s and the deep quartz gold mines at Bendigo in the 1880s.During the golden years of alluvial mining in the 1850s, and later out on the frontier fields of Kalgoorlie and Jarrahdale in Western Australia, the lure of the mine dominated family life. How could it do anything else? The canvas tent, bark hut or weatherboard cottage in which the mining family lived close by the mine facilitated prompt access. The working man of the family attended to the demands of the mine first, and those of his family afterward. Who then organized and nurtured the mining family? The role of the mining wife was multi-fold. She played the traditional roles of home-maker and comforter, raising her children, tending her house and vegetable garden and supporting those friends and acquaintances who had lost children to disease, or menfolk to the mine. Epidemics of measles, the whooping cough or influenza carried away children in infancy or at too young an age. The death of a husband through accident or disease (pthisis was a likely killer) forced upon the mining wife another role, that of provider. When Elizabeth Vigus' husband died in a Bendigo mine accident in March 1880 Elizabeth set up a grocery business to support her young children.' But in other cases the mining wife supplemented the family earnings by part time work, not in the mines for the Mines Act legislation of 1842 forbade the working of women underground, but in auxilfiary occupations which were in demand.2 Ann Mitchell, a herbalist ,found plenty of work in the goldfield towns of Daylesford and Maldon in the 1860s and 1870s.3 So too did Susan Rule and her daughter Catherine who conducted a sewing and millinery establishment in Beechworth in the 1870s.4 The making of the family's clothes was another task of the mining wife and mother.Until the wonderful invention of the sewing machine, this was a tedious and time-consuming task. James Slater Edmonson bought his wife a Wertheim for the sum of 12 pounds in June 1886, just before leaving her and his chil- dren in the Adelaide suburb of Goodwood whilst he went alone to the goldfields of the West. In October of that year he wrote to Louise telling her how he missed the childrens' wondering "whether Slater wore my old shirt now. I always think of him as he sat on my knee at breakfast in that old shirt; and how pleasant it would be if I could rock both of them and sing as I used to do".5

Jan 1, 1988

Surface geological observations are predominantly two-dimensional but can be expanded into three dimensions using geophysical techniques. These techniques have proved succ- essful in the past and will be utilised more frequently in future mineral exploration. Geophysical training establishments must recog- nize future requirements and teach geophysics as part of a broad earth science course as well as a specialised geophysical course. Central- isation of teaching skills, the use of high- technology in the classroom, and greater interaction between academic and industry staff are recommended as a means of ensuring a vibrant geophysical training base in Australia, for the geophysicist of the future.

Jan 1, 1986

By S Januszewski and, G Dirom, D Christensen

Four field test plots were constructed in 1998 on a sloped waste rock surface at the Myra Falls Operations of Boliden Westmin (Canada) Limited to evaluate hydraulic performance of alternate cover system designs. The field test plot cover systems were designed to control oxygen ingress and water infiltration to the underlying waste rock while providing a medium for a grass and legume vegetation cover. The test plots consisted of a bare waste rock surface (control plot), and three additional plots consisting of native compacted till placed directly on the waste rock surface, overlain by non-compacted till. Two of the test plots included a compacted till layer ameliorated with flyash and bentonite, respectively, to improve moisture retention and reduce permeability. The third test plot consisted of a compacted layer of native till overlain by non-compacted till. A performance monitoring system was installed in each test plot to evaluate net percolation and oxygen ingress to the underlying waste rock. In addition, each test plot has profiles of matric suction, water content, and temperature sensors installed at up-slope and down slope locations. A review of four years of monitoring data shows that the compacted till/bentonite cover system has been most successful in limiting the infiltration of meteoric waters and oxygen ingress to the underlying waste rock material. The compacted till/flyash and compacted till cover systems have produced similar net percolation results and neither have functioned well in maintaining an oxygen ingress layer throughout the year. The amelioration of bentonite with till to produce a compacted barrier layer shows promise in reducing water and oxygen ingress at the MFO site, while the incorporation of flyash with the till did not result in a significant increase in performance. The field performance data clearly demonstrates the need for developing field trials prior to full-scale construction, as opposed to relying solely on an un-calibrated numerical modelling to design the full-scale cover system.

Jan 1, 2003

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

By Toguri JM

A solid electrolyte technique has been used to measure the activity of cobalt in liquid cobalt-gold alloys containing between 0.085 and 0.50 mole fraction of cobalt, and for temperatures from just above the liquidus to around 1550 K. The system exhibits positive deviation from ideality, both in the activities of cobalt and gold, and in the enthalpy and excess entropy of mixing. The results agree with previous measurements using a Knudsen cell - mass spectrometer technique, but differ from those reported for a gas equilibration method. The data have been used to calculate the activity coefficient of cobalt oxide in silica saturated iron silicate slags and to express the solubility of cobalt in such slags as a function of cobalt activity and oxygen pressure.

Jan 1, 1984

An account of milling "methods and costs at Mount Isa Mines Limited up to the year 1938 has been published. The present paper outlines the methods since adopted in the milling of lead-zinc ores and presents a description of the equipment now being provided for the milling of copper ore.The programme approved for the mining, milling and smelting of both lead-zinc and copper ores involves the milling 9f 50,000 tons of lead-:-zinc ore and 35,000 tons of copper ore per month.The crushed ores will be delivered to the surface from alternate levels through No. 2 Ore shaft and conveyed to their respective crude ore bins at the crushing plant. The ores will be crushed and milled in separate circuits in common buildings and the tailings will be stored on a common tailings dump. The water services to the two circuits will be separate.LEAD ZINC PLANTCrushing PlantThe crushing plant described in the previous paper was located adjacent to the Urquhart shaft. The crushing plant had grown considerably over the years by the addition of a 4ft. BY-mons shorthead crusher and a set of Traylor 72 in. x 20 in. crushing rolls and, whilst operating satisfactorily, was difficult to maintain and cramped in many places. As a satisfactory layout for the new copper crushing plant could not be made in the vicinity of the, existing plant, it was decided to construct a new plant on the western side of theconcentrator building and provide identical equipment in...

Jan 1, 1953

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880's with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978-81 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6% Sn). Spectrum Resources Australia Pty Limited acquired a 98 percent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to lmm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of 6-7 years.

Jan 1, 1990