Search Documents

By Y Gu, W McCallum

Mathematically sophisticated methods are now in common use for metal balancing of complex separation flow sheets at many concentrators. These balances usually entail minimisation of the sum of weighted squares of data adjustments subject to flow sheet constraints. The adjusted data provides numerical consistency across the complete flow sheet to facilitate performance calculations. A mine with multiple ore sources can be considered as a flow sheet with the end node comprising the concentrator and its products concentrate(s) and tailings. If the mass transfer and grade estimates for each ore source are sufficiently reliable, a similar metal balancing approach can be used for combined mine and concentrator data. Comparison of balanced and measured assays and mass movements provides useful guidance to security of marginal grade ore and possible dilution problems. This paper includes a summary of results from a case study based on a mine with multiple ore sources.

Jan 1, 2002

By Wright S

Single pellets of mixed lead-zinc concentrate containing up to 20 % lead were roasted in the temperature range of 800-1100¦C. Variables studied included pellet size (from 9-8 to 3-2 mm diameter), gas flowrate past the pellet (from 0.05 to 5 ms t), composition of the atmosphere and the effect of additives such as zinc oxide and silica. After defined periods of time, the pellets were removed from the furnace, quenched and submitted for chemical, XRD, SEM and microprobe analysis. The oxidation of the zinc sulphide followed a shrinking core model. Temperature measurements showed that very high pellet temperatures were experienced at the start of an experiment but after 5-10 minutes these approached a constant temperature. The lead loss from the pellets was then constant with time. Thermodynamics predicted the presence of two bands of lead material in the reacted layer of the pellet. These were found in practice. The lead loss from the pellet occurred from the outer oxysulphate layer via the vaporization of lead oxide polymers. The vapour pressure of PbO, and the loss of lead, was dependent on temperature and bulk gas concentrations of SO2 and 02. At 1100¦C the addition of silica greatly reduced the loss of lead from the pellet. Physical factors such as pellet diameter and gas flowrate past the pellet affected the particle dynamics. These results were found to vary in accordance with the predictions of the Froessling equation.

Jan 1, 1989

By Richards AB

This paper describes the ENVIB software system, which has been developed in a menu-driven form to aid in the monitoring and assess- ment of vibration caused by routine blasting operations and for research and development projects. The paper gives an outline of the capabilities of the system by means of screen-dumps and a general descriptive commentary. Technical notes have been added where appropriate to further describe the system. The ENVIB system covers: I . Analysis of blast vibration results, and preparation of graphs and tables for control and estimation purposes. 2. Effects of atmospheric conditions and air vibration propagation. 3. Real-time acquisition and analysis of analogue blast vibration sig- nals directly from transducer equipment or from FM tapes. 4. Analysis of digital files on floppy disc or transferred via the serial port from blast monitoring equipment. 5. Transfer function calculation for structure response studies.

Jan 1, 1988

By Gadd D. E

Since October 1972, New Zealand Steel Mining Ltd has loaded around 10 million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110,000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the shiploading system and attempts to answer the question: "If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?".

Jan 1, 1980

By P Andrieux

By 1996 ground control-related problems at Brunswick Mine had raised serious concerns regarding the safe and economical extraction of large portions of the reserves. These difficulties were mainly caused by high stress levels in pillars, instabilities resulting from wide spans supported by ageing support elements, and chronic difficulties supplying rock fill from the surface quarry to the underground workings, which resulted in many large voids remaining open for long periods of time. Significant changes have been implemented at the site since 1996, amongst which were a change of mining method, the introduction of paste backfill, the establishment of stress management measures, and the introduction of shotcrete on a large-scale. This paper focuses on the regional ground conditions associated with both the previously used primary-secondary mining method and the newly implemented pyramidal pillarless technique, as well as on some of the stress management measures implemented at the mine.

Jan 1, 2000

By Ward C. W

Conventional polygonal and block modelling techniques inadequately represent the grade-thickness distribution of some narrow shear and stratabound gold deposits. The polygonal influence of high-grade drill intercepts can result in overestimates of resource tonnages at high-grade cut-offs. Although block modelling methods provide grade smoothing and a better representation of structural continuity, the technique can lack precise definition of ore width. An alternative method known as Spatial Object Modelling (SOM) has been developed on MineMap software to overcome some of these modelling issues. This method does not rely on a uniform cell size and allows grade smoothing between resource intercepts in three-dimensional space. The SOM technique creates grade-thickness bars on regular, user-defined spacings which allow easy visual comparison of raw intercept data to the interpolated model. Model cell values are readily transformed into isopachs, isopleths and resource perimeters for reporting and mine planning purposes.

Jan 1, 1997

By Segnit R. E

Two suites of dusts (waste-heat boiler and electrostatic precipitator) collected in 1976 and 1980 from the Kalgoorlie nickel smelter were subjected to chemical and XRD analysis and were examined by SEM and optical microscopy. The spherical to sub-spherical particles contained oxide and glassy phases with small amounts of sulfide. XRD showed that the major phase was a mixed Ni-Fe oxide spinel with some hematite. These phases compared well with those predicted by thermodynamics. The particle size distributions showed that in the 1976 and 1980 suites 20 per cent by weight was respectively coarser than 60 and 115/lm (boiler dusts) and 40 and 30/lm (precipitator dusts). Maximum particle sizes estimated from sedimentation chamber theory were found to be in reasonable agreement with the maximum sizes found in the dusts.

Jan 1, 1984

Alternative processes for converting coal to liquid products and their stage of development are outlined. The merits of hydrogenationprocesses in general, and the solvent refined coal process in particular, are stressed. Bench scale experimental hydrogenation procedures used by the Australian Coal Industry Research Laboratories Ltd. (ACIRL) to study the liquefaction of Australian coals and correlations between properties of such coals and their conversion to liquid products are described. Factors involved in assessing investment and operating costs for modern hydrogenation based coal refineries of different capacities are described with reference to a recent study undertaken in N.S.W. The significance of coal properties such as yield and yield structure of total liquid products and how they and other factors can influence the economics of the coal refining operations are discussed.

Jan 1, 1977

By Wright G. N

Curragh Queensland Mining Limited, a co-venture of Australian and overseas interests, operates an open cut coal mine 13 km north of the township of Blackwater in Central Queensland, refer attached location map.

Jan 1, 1992

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Boyd G

This paper describes the planning, analysis, design and operational experience of highwall mining based on auger drilling techniques applied to thick coal seams exposed in an opencut highwall. Being the first time such technology has been used in Australia, a large commitment to technical design and logistics planning was given by Callide Coalfields Pty Ltd. This commitment included technical and operations management and supervision, mine services, and the retention of consultants to undertake geotechnical analysis, instrument preparation and instrument installation.

Jan 1, 1991

By Lee Y. K, Walker G. S, Bronswijk V. W

The effect of leaching three samples of Mt Weld ore with a-hydroxysulphonic acid [(CH3)2(COH)SO3H] was assessed. Apatite present in the samples was found to be readily soluble but calcination up to 600¦C was required to increase the solubility of crandallite. Increasing the calcination temperature increased dissolution of both phosphate and alumuuum. The optimum SO2 content in solution for the dissolution of crandallite ores was found to be lower than for apatite.

Jan 1, 1991

By Kerr I. D, Kennedy M

Flash X-radiographs were obtained of commercial electric No 6 and No 8* strength aluminium tube detonators in small-diameter cartridges of emulsion explosive at various times after fusehead operation. The trigger system for the radiography was based on the detection of light following fusehead firing via optical fibres inserted into the fusehead cavity during detonator assembly. These experiments were simulated using a finite element hydrocode with realistic treatment of the non-ideal reaction kinetics. Excellent agreement was demonstrated for the shape and position of the shock waves. In both cases, initiation of the emulsion was predominantly forward from the detonator. For the No 8* strength detonator, this initiation resulted from the shockwave delivered through the sides of the detonator, while for the No 6 strength detonator, initiation was the result of a complex interaction between shockwaves originating both from the sides and from the endcap. In the reverse direction (towards the crimped end of the detonators), initiation was only weakly dependent on detonator strength, being controlled mainly by the competing processes of rarefaction from the cartridge boundaries and comer turning of the detonation wave from the forward initiation. The consequences for field performance of small-diameter emulsions will be discussed.

Jan 1, 1990

Mine evaluation methodologies are well suited to evaluating many projects in capital-intensive industries other than mining. These industries include oil, gas, power generation, transport and infrastructure projects. A case study of an open cu

Jan 1, 1998

By Johnston RRM

There have been many published mathematical models that, to varying degrees of sophistication, attempt to describe dynamic thickener behaviour. CSIRO has undertaken to develop a model under industry sponsorship. Recently developed instruments such as the floc density analyser and natural gamma-ray gauge have enabled new data to be collected from plant thickeners for model validation and development. The principles behind the use of the natural gamma-ray gauge are described and the possibilities for its use as a control instrument in the bed have been examined. A simple nomograph illustrates how the gamma-ray gauge data can be used to predict steady state underflow consistency and bed Position.

Jan 1, 1991

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

Extensive reserves of kaolin of the type suitable for use as a high quality paper coating exist on the Weipa Peninsula. In 1986 a commercial processing plant was constructed to produce 100 000 tonnes per annum of coating quality kaolin targetted principally for export. A number of processing difficulties have limited the production capability of the plant. The prime area being the pressure filtration operation with achieved cycle times being around 50-60% of design. The rate determining steps being press filling, press unloading and filter cloth washing. This paper details and summarises testwork and results from our attempts at decreasing the filtration cycle time.

Jan 1, 1989

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

By Hopkins G. M F

Intensive exploration of the Archaean ultra mafic sequence bordering the Kambalda dome has resulted in the discovery of at least ten dis- tinct areas of nickel sulphide mineralisation subsequent to the initial drill intersection in January, 1966. Sulphide ore reserves to June 30, 1972 were 19.36 million tonnes at 3.3% nickel after mining of 3.0 million tonnes at 3:7%,nickel since production commenced in March, 1967. About 75% of contained nickel metal reserves occur in sulphide concentrations located at the base of the-ultramafic sequence, in contact with underlying meta-tholeiitic basalt. The remaining reserve occurs in concentrations of sulphides within the ultramafic sequence, usually within 100 metres of the underlying contact and typically in proximity to contact mineralisation. These hanging wall orebodies are smaller, contain significantly lower con- centrations of sulphide, and generally exhibit higher Ni:S ratios than underlying contact ore- bodies. The majority of contact sulphides concentr- ations form narrow, elongate, north north-west trending bodies, closely coincident with fault bounded depressions in the contact. Detailed study of the Lunnon Shoot ore environment in- dicates that it was a locus of crustal failure during, and subsequent to, emplacement of ultra- mafic rocks. Resultant structures parallel and

Jan 1, 1973

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991