Search Documents

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Morgans DJ

The aim of this paper is to highlight the social aspects involved in the preparation of environmental impact studies (E.I.S.'s) for mining developments. In particular, the paper will reveal that the social information provided in such E.I.S.'s can achieve much more than simply satisfying government requirements. Such information can form the basis of a strategy to deal with the settlement of a mine workforce in either an existing or newly developed community. A strategy of this type can go a long way towards avoiding many of the social problems and related industrial disputes often created in such circumstances. It will also be of significant benefit to the mining company in negotiating its infrastructure package with the local authority.

Jan 1, 1987

BlIP Minerals is a large, diversified, international mineral producer. This paper describes the company's operating strategy, and identifies the role of mineral processing in this strategy through three examples: the column flotation installation at Escondida in Chile, the leach-SX-electrowinning plant, proposed for Escondida, and the whole-ore roasting process being constructed for the Syama gold operation in Mali. It is concluded that the application of appropriate and sometimes novel mineral processing technologies can achieve significant benefits in reduced operating cost, improved product quality, and in some cases the exploitation of previously uneconomic deposits, thereby providing strategic advantages to the company.

Jan 1, 1993

Changes in prices and costs change the mineable grade and the profitabil- ity of an ore reserve. In a static world the grade required for an ore reserve is measured by the ratio: Cost/tonne of ore x 100 Price received/tonne of product and profitability by the ratio:- Price received/tonne of product Cost/tonne of product If the words cost and price refer to average cost and average price over some suitable period, say 3 to 5 years, the above ratios express the convent- ional wisdom of the mining engineer, and assume there will be no change in technology or politics.

Jan 1, 1979

By Kepplinger W

The COREX process is a technology for production of liquid hot metal on the basis of coal (without the use of a coking plant) developing by VOEST- ALPINE AG, Austria and its subsidiary company Korf Engineering GmbH, Federal Republic of Germany. CORED is a registered trademark of VOEST-ALPINE AG and Korf Engineering GmbH. The COREXW process is based on the idea of separating the process steps realized in the blast furnace (gene- ration of reduction gas, reduction of iron oxide and melting of the reduced iron) and including partial coking of the coal.

Jan 1, 1987

The Horn Island gold and mineral field produced 194 kilograms of gold in the 4 years subsequent to its discovery in 1894, from an area of shallow workings 1.5 kilometres x 0.5 kilometres. Gold deposits in the adjacent Prince of Wales, Hammond and Possession Islands also drew attention at that time.These islands form part of a Carboniferous sequence of ignimbrites (Torres Strait Volcanics) intruded by the Badu Granite and minor volcanics within the Cape York-Oriomo Ridge. Gold is associated with the epithermal stages of igneous activity. Recent exploration has defined sub-horizontal zones of disseminated gold mineralisation in the sub-surface, as well as reserves in the outcropping sub-vertical structures mined in the past. Released estimates of 170,00 tonnes proven ore and 550,000 probable ore at 4 grams per tonne gold, have been established.Gold is mostly contained in quartz vein stockworks and hydrothermal breccias within the intensely propylitised medium grained granites which form the local host rocks within the coarse grained Badu Granite. Associated vein minerals are sulphides (primarily of lead, zinc and iron) and calcite. Various intrusions of porphyry, aplite and granodiorite occur through the prospect area.

Jan 1, 1986

By A Singleton, J Busfield

World coal producers have been under constant pressure in recent years because of falling export prices arising from oversupply and the Asian slowdown. This has resulted in a dynamic market place, a sharpening of focus on bottom line costs and some rationalisation of participants. Productivity has increased dramatically as many inefficiencies, typical of the coal industry, have been eroded through workplace reform. This is true for the both open cut and underground sectors of the industry. At the same time, the technology of underground mining is undergoing dynamic change. Mine operators are implementing better exploration and planning tools and are also starting to make gains against chronically low equipment availability and utilisation. æStep-changeÆ improvements in output are imminent. As the statutory environment shifts to a æduty of careÆ regime, it is hoped that mine safety performance will improve, particularly with regard to fatalities. The focus of the paper is on the Australian coal sector, although references to international benchmarks are made. Despite environmental threats to the future of coal, it is concluded that the next ten years will see impressive performance results from underground coal mines which will assist coal to maintain its position as the preferred fuel of lowest cost.

Jan 1, 2000

The role of automation in the environmental management of the various stages of mining projects is discussed. Remote sensing can be useful in the exploration phase, but tends not to have sufficient resolution for individual operations. Automatic samplers, whether for meteorology, air or water, are widely used, but can have operational problems. The environmental scientist, the electronics engineer and the computer programmer must combine in the future to develop products which are applicable, robust and simple to use.

Jan 1, 1985

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

Polyacrylamide flocculating agent has been used in the Leaching Division of the Risdon Works of the Electrolytic Zinc Co. of Australasia Ltd since October, 1960. Since the introduction, the.: number of thickeners in use in the continu-ous thickening stage has been reduced from eight to three; there has been an increase of 25% in throughput and a reduc-tion of solids in.:thickener overflow from 3-4 gòpòl . solids to 0.5 g.p.l. solids. Reagent addition has been at the rate of 0.25. lb SEPARAN, NP10 per ton solids.Additionally there has been a gain of 3% in current efficiency as the direct result of the addition of SEPARAN NP10 to purified cadmium sulphate solution prior to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strip-pings from 47 to 71 hours. However, there has been a slight increase the lead content of the cadmium-metal produced.

Jan 1, 1963

Utah's Blackwater mine began operations in 1967. The four CQCA mines controlled by Utah followed over the period 1971 to 1979. Project feasibility studies for all these were based on open cut mining to overburden depths of 60 metres, with typical project lives of 12 to 16 years, depending on reserves Further studies, initiated after the mines had started, showed that continuation of open cut mining beyond the 60 metre highwall was viable. In 1973, the Deep Stripping Project (DSP) was launched to define the scope for stripping deeper, to determine what the additional equipment needs might be, and to pu forward proposals for a full scale trial system. The project commenced at grass roots with a literature survey, proceeded through a sequence of equipment evaluation, specification, design and manufacture to the commissioning of the Goonyella BWE system. Studies are continuing to assess the future deep stripping requirements for all Utah's Bowen Basin mines.

Jan 1, 1983

By Alder KF

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials. This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products. This paper presents some predictions of the possible growth of nuclear power installations in Australia. These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50% of new generating plant might be nuclear. Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme. - The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel'; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1970

By Lauha E. A

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike subdistrict, there are seven major deposits; Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the subdistrict are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Bamck Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post, and Deep Star occur both on Barrick and Newmont Property.

Jan 1, 1991

By Roberts I. R

The movement of materials is normally associated with a number of problems, some more easily overcome than others. Orebodies are frequently located in remote areas to which transport lines have to be opened. In the case of Mount Isa Mines Limited, the geographical isolation from the major consumer areas necess- itates long lines of transport and communica- tion. The problems associated with transport of metals and minerals vary from time to time because of the changing industrial environment. The increased size of vessels, changes in handling methods, and the economic pressures brought on by increased costs of transport without any guarantee of aligned increase in metal prices all contribute to difficulties which have to be faced by the mining companies in their effort to reach the markets with their products.

Jan 1, 1974

By Savage E. N

The porphyry copper minerals of Melanesia occur within a host of narrow veinlets in predominantly quartz diorite stocks or as contact metasomatic masses in skarns adjacent to the intrusion. Some 90 per cent of the constituent minerals comprise pyrite or marcasite, chalcopyrite, and magnetite with the remainder mainly bornite and hematite with accessory rutile and chalcocite together with several trace minerals. Gold is found mainly as inclusions in chalcopyrite, and minor molybdenite occurs likewise.Of particular significance is the persistent occurrence of accessory rutile of hydrothermal origin intimately intergrown with chalcopyrite. The rutile occurs relatively late in the hydrothermal sequence and upon weathering of the deposit may be released on a cumulative basis possibly in sufficient amounts to constitute a particulate pathfinder mineral which may aid in prospecting.Rutile is present in all the Melanesian occurrences studied and is also prominent in several American deposits.The porphyry copper mineralogy is characterized by the presence of accessory hydrothermal rutile intergrown with chalcopyrite.

Jan 1, 1975

By DJ McKEE

Process control emerged in the mid-1960s as a new and exciting method of improving the performance of mineral processing operations. The early Australian developments, principally in Broken Hill and Mount Isa, were based on pioneering work in instrumentation, the availability of small digital computers and a particularly effective partnership between companies with technological foresight and University and CSIRO research groups. Initial progress was rapid and within ten years many plants were committed to process control. Process monitoring is now routine and most circuits have some level of control. However, few plants have comprehensive optimising control systems as the difficulty of developing control strategies which can cope with the wide variety of conditions encountered in most mineral plants has been fully appreciated. This paper summarises past experience and assesses the degree of application of different forms of process control in metallurgical plants. Barriers to the effective utilisation of opt rising control are identified and some suggestions for advancing the application of control are made.

Jan 1, 1992

THE science of topography deals with the various natural and physical features of the earth's surface. These features are determined by the manifold constructive and destructive processes of nature, and their many diverse forms and characteristicsare dependent primarily upon geologic structure. Thus it is that a close relationship exists between the rocks of a region and the topographic features of the lJountry wherein they occur. Again, the existence of all sorts of mineral wealth is dependentupon the nature of the rocks, and their extension is directly connected with the topographic features represented upon the enclosing land-area.In studying any district with a view to deciphering its geological structure, to locating any mineral deposits it may contain, and to ascertaining, so far as a surface-examination may show, their probable and economic possibilities, it is therefore ofprimary importance to have at hand a correct topographical map of the area under investigation.GENERAL REMARKSThe actual amount of topographic detail shown will depend upon the money and time available for topographic surveying and upon the scale upon which the final map is to be produced...

Jan 1, 1912

The fast rate of development in the micro technology industry is enabling computer based systems to be used in ways never considered before. Micro technology can be used to great advantage in the mining industry to improve both safety and productivity. The planned use of electronic 'IN/OUT' boards at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) mines will provide a much improved system for checking that the mines are clear before firing. The provision of remote ocaputerised core logging facilities made possible by small remote data entry terminals will greatly improve the productivity of the personnel involved in all stages of core Logging.

Jan 1, 1983

The Jurassic Walloon Coal Measures crop out over much of the Moreton Basin and contain numerous thin, banded coal seams which have been mined at various locations since the 1870s. Historically most mining has been by underground methods. Increased exploration during the 1970s and 1980s has led to the delineation of significant open cut coal resources and to the development of the Oakleigh, Jeebropillly and Ebenezer open cut coal mines in the Rosewood-Walloon area. Over 2 170 million tonnes in-situ of shallow, high volatile bituminous coal with a mean maximum vitrinite reflectance of between 0.5 and 0.6 have been proven in the Basin.

Jan 1, 1991