Search Documents

By Montini A

The dynamic behaviour of the load in a pilot-scale ball mill has been measured as a function of axial position within the mill, end plate lifter design, load volume J (percent of mill volume), percent solids in the slurry S and mill speed N (percent of critical speed). Conductivity probes were inserted through the shell of the mill to provide online measurements of the dynamic orientation of the load in the mill. It was found that 1. the height of the shoulder of the load is increased by increasing J, S or N. 2. Measurements of the effect of S on the location of the shoulder of the load should be very useful in mill control strategies. 3. The axial centre of gravity of the load in the mill is not affected by operating conditions. 4. The presence of lifters on the feed end plate does not affect the torque drawn by the mill. 5. Holdup of slurry in the mill is a strong function of slurry viscosity and a weak function of mill speed.

Jan 1, 1986

By I Zh Bunin, V A. Chanturia, V G. Minenko, M V. Ryazantseva, A L. Samusev

A promising source for the extraction of rare metals and REEs in Russia is the eudialyte ores of the Lovozero deposit, which do not contain active uranium components. The eudialyte ore reserves of the Lovozero Massif are considered virtually unlimited and therefore have the potential to become a primary source of a number of rare and rare earth metals. The goal of this study was to comprehensively examine the effect of the parameters of high-power nanosecond electromagnetic pulses (HPEMP) and dielectric barrier discharge (DBD) on the leaching performance of eudialyte concentrate and the selective separation of zirconium and REEs from productive solutions. Using scanning electron microscopy and infrared spectroscopy, the mechanism behind the intensification of acidic dissolution of eudialyte as a result of pretreatment with energy impacts was described. During the HPEMP treatment, weakening and destruction of the eudialyte surface was observed, which at the substructural level is expressed in the deformation and local destruction of Si10O27, Si9MO30 resulting in formation of microcracks. During the DBD treatment, the formation of characteristic defects was observed in the form of imprints of dielectric breakdown microchannels and individual mineral fragments. Pretreatment of eudialyte concentrate using HPEMP made it possible to increase the recovery of zirconium into the pregnant solution of leaching by 3.4–4.3 per cent (from 86.6 per cent to 90.9 per cent) and by 4.1 per cent (from 86.6 per cent to 90.6 per cent) when using DBD. The increase in the total recovery of REEs was 1.2–1.8 per cent (from 87.7 per cent to 89.2 per cent). The effect of pH values, solution temperature, initial concentrations of valuable components on the successive recovery performance of zirconium and REEs from the pregnant solutions nitric from the acid leaching of eudialyte concentrate by chemical precipitation was examined. The possibility of selective separation of the zirconium product and rare earth elements with a zirconium recovery of 99.95 per cent and a REE recovery of 87.5 per cent was established. REE loss with the zirconium product was 8.0 per cent and 4.5 per cent with the spent pregnant solution.

Aug 24, 2022

By D Moy, T Carter

This paper outlines the feasibility assessment conducted to explore the possibility of constructing two submarine water supply pipelines beneath the Ma Wan Channel in Hong Kong using either horizontal directional drilling or tunnelling. The Ma Wan Channel is a major shipping channel in the Northwest New Territories, which separates Ma Wan Island from the mainland. The challenges faced by the projectÆs designers included space limitations on either side of the channel, marine department restrictions on construction activity within the channel and selection of a suitable crossing alignment and profile given the channelÆs depth, irregular sea floor topography and complex geology. The existing geological information indicated the proposed alignment would cross granitic and volcanic formations, which would likely be faulted. The primary concerns with horizontal directional drilling were:the length, diameter and depth of the crossing were at the limit of precedent experience in rock; the lack of available space at both the entry and exit sites; and whether the technique would be flexible enough to cope with the anticipated range of ground conditions. The primary concerns for tunnelling were: the possibility of encountering large inflows of high pressure groundwater; andthe possibility of encountering disturbed ground within the fault zones which could flow if not properly treated. As a means to evaluate and mitigate these technical risks for both construction options, a directionally drilled pilot hole was used to investigate the ground conditions along the proposed pipeline alignment. The pilot hole results indicated that either directional drilling or a closed face TBM drive were technically feasible crossing options at a crossing depth of 80 m. The results also indicated that either an open face TBM or a drill blast drive would need to be constructed at much greater depth because of the presence of highly permeable, disturbed ground in mid-channel at this crossing elevation.

Jan 1, 1999

The south-east Missouri cobalt-copper-lead-zinc district is the worldÆs largest lead producer and a significant producer of by-product zinc, copper, cobalt, silver and cadmium. Current production in the district comes from six or seven mines in the Viburnum Trend. Most ores in the Viburnum Trend are characterised by a small number of minerals with simple compositions. Portions of some orebodies contain ores that exhibit greater variations in mineralogy, and these include shale-hosted lead- copper ores, bornite ores and nickel-arsenic sulfide ores. Ore textures include both replacement and open space filling textures, and the paragenetic sequence for the ores is characterised by repetitive periods of deposition of all of the ore and gangue minerals. Ore microscopy is an effective tool for not only the identification of the minerals and textures shown by the ores, but also to determine the mineralogy and textures responsible for beneficiation problems. An interesting variety of sedimentary and structural ore controls have determined the locations of individual orebodies in the district. Based upon the positions of orebodies with respect to Precambrian ridges and knobs, together with areal patterns of mineral/metal zoning, it is interpreted that the ore fluids came from diverse directions to form the deposits in the district. It is concluded that the Old Lead Belt subdistrict was mineralised by fluids that flowed from the north-east and north-west, the Fredericktown area by fluids from the north-east, the Indian Creek subdistrict by fluids from the north-west and the Viburnum Trend by fluids from the north-west and west.

Jan 1, 2008

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

By A Goldstone, M Fitzpatrick

Contemporary mine wastewater flows are subject to stringent water quality standards before discharge to local waterways. Strict criteria are often applied as a result of fears of extensive acid mine drainage; a feature of the many abandoned mine adits around the Coromandel, Central Otago, and the West Coast. In most cases the USEPA water quality criteria have been used to set treated wastewater discharge water quality standards. In future it is possible that the recently published ANZECC water quality criteria guidelines will be used for this purpose. The ANZECC guidelines also provide for the establishment of discharge criteria at specific sites, rather than accept the trigger values. The use of site-specific criteria for treated wastewater mine discharges was pioneered at the Golden Cross gold mine, near Waihi, in the late 1980s. The procedure used to derive water quality criteria was based on USEPA guidelines. In developing the Golden Cross criteria, only species that occur, or are similar to those that occur in the Waitekauri River were used. The mine commenced discharge of treated wastewater in 1991, and macroinvertebrate communities in the vicinity of the discharge point have been regularly monitored twice a year for the past 12 years. Despite fluctuations in community composition and abundance over that period, no permanent significant changes in the macroinvertebrate communities occurred between sites above and below the treated wastewater discharge. The success of the site-specific criteria at Golden Cross has shown how the application of this methodology can result in the protection of aquatic life while allowing for the discharge of treated mine wastewater.

Jan 1, 2003

By N J. Welham

This paper reports on an innovative professional development program for school science teachers run collaboratively between the Centre for Sustainable Resource Processing and Murdoch University. Ultimately the initiative aims at increasing the pool of school students with strong science and mathematics backgrounds while highlighting the challenging careers available in the mineral resource sector including the gold industry. The program is unique in that it seeks to develop a network of science teachers who may participate in a series of workshops, short courses and tours over several years. The objective is to raise secondary school studentsÆ awareness of potential careers within the minerals sector by exposing teachers to a real life, hands-on look into the mining and minerals resource industry. Though the program includes the breadth of the resource processing sector, the potential value to gold processing is in developing a greater pool of potential employees. The initiative allows teachers to develop a better insight into the practical applications of the theoretical sciences they are required to teach. The evolution of the program from the first trials with Western Australian teachers to the introduction of the initiative to Queensland teachers are reported on. Additionally, the results of a pilot study involving 40 participating teachers are described. This study used a questionnaire and follow-up interviews to gain quantitative and qualitative feedback from teachers. There is evidence that the professional development program has resulted in teachers acquiring a new found appreciation for the application of the fundamental chemistry and physics they teach within the school curriculum. Also reported are associations between teacher participation in this professional development program and changing attitudes towards the industry in a positive way. Finally, there is some indication that these positive teacher attitudes may result in their students developing a better understanding of the diversity and availability of career paths within this industry.

Jan 1, 2007

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Close spatial relationships between the deposits of the Etheridge Goldfield (23,000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic. Acceptance of this hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so. Consequently there is little scop- for the discovery of extensions of this field. However, the stratigraphic interval between the source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1980

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and*pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anortho- site layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spinel-bearing meta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the Goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, Ni, etc. liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By J Abols, T Hughes

The selective recovery of gold and silver from solutions containing other metals, such as copper, is possible using AuRIX«100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated, opening the possibility of producing high grade gold dorT from high grade silver pregnant leach solutions. This paper reviews the AuRIX«100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX«100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX«100 is being tested.

Jan 1, 2005

By Warner N. A

There is an inherent problem in producing simultaneously lead, zinc and copper as metals in a single polymetallic smelting furnace. It relates to the condensation of lead and zinc from the gas phase under vacuum conditions such that metals in bulk form, either solid or liquid, are obtained as products rather than a fume or dust containing both metallic and non-metallic components. To understand this phenomenon, it has been necessary to establish mathematical models with computer simulation to identify the process requirements for effecting the objective of maximum bulk metal production with minimum fog formation. The theoretical framework of simultaneous heat and mass transfer involved in condensation from gas mixtures containing a non-condensable gas has been extended to the high temperature and reduced pressure conditions. These apply to new technology for polymetallic smelting now being developed in a project currently funded jointly by the Commission of the European Communities and the Mineral Industry Research Organisation. Under the right conditions it is theoretically possible to condense out both lead and zinc with minimal fume formation, but in all practical cases it is anticipated that some circulating load for reversion back to the smelter will be needed.

Jan 1, 1989

By Voermans F. M, Hoyle M. W H

The Archean geological sequence in the West Pilbara region (Fig 1), a deformed greenstone volcano-sedimentary succession regionally intruded by layered mafic/ultramafic lopoliths, batholithic granites, granite stocks and transected by swarms of dolerite dykes, has prompted several companies to search for a variety of base metals and and platinoids (Fig 2). In the first instance, detailed aeromagnetic surveying was completed, producing patterns of marked magnetic anomalism which proved substantially successful in the demarcation of areas warranting geological reconnaissance and detailed follow-up. Revelant to this paper were the obvious magnetic features overlying outcropping and buried mafic/ultramafic bodies which ultimately were proven to be host to Ni-Cu sulphides, pgm, Ti, V, Cr and, more recently, Ag and Au mineralisation. Routine stream sediment, soil sampling and ground geophysical techniques of the day appear, in most cases, to have been adequate in the detection of mineralisation, except in the case of Radio Hill massive sulphides where the Turam E.M. (1972) signal essentially failed to detect the blind conductor (Peters, de Angelis 1987).

Jan 1, 1988

IN any assay office it is of paramount importance to keep the men interested in their work; and in order to do this, men on routine work, such as lead, zinc, and sulphur deterrrrinations, slag analysis, etc, should be changed around monthly. This gives some variety and helps to keep a man's interest on his work, so that better work results. It may be maintained that to keep a man on the same class of work indefinitely makes him more expert at his work. This is certainly true; but in assaying, where accuracy is so essential, it is absolutely necessary for a man to keep his mind on the work, and not 'get' into a mechanical method of working. He is also on the alert to discover means for shortening his analytical methods, and his capacity forwork is increased. Another advantage is that the men get a good all-round training, and one is never at a loss to replace a man on any class of work when he is absent from any cause. This tends to smoother and more efficient running of the assay department. In industrial assaying it is often advantageous to have a result quickly, so that it will be of maximum benefit in the running of some part of the plant, In such a case it pays to sacrifice a little accuracy to speed up a method. The shortest method is less costly, and a quick approximate method is all that is required to give the superintendent the requisite information. Time is thereby saved, and the cost is less. In carrying out assaying for any large industrial plant, such as a smelting works, there is always a tendency for superintendents running the different departments to send in more samples for assay than are absolutely necessary when no system of costing is in operation. Some of these samples may involve a lot of work and heavy expenditure, as, for example, the estimation of only one impurity in a sample of refined lead. If the superintendent knows that the cost of assaying all samples sent in by,him is charged up directly against...

Jan 1, 1922

By Senanayake G

A sample of crude copper powder produced by the CLEAR Process was refined by dissolution and recovery in sulfate media using the Parker Process. The Parker Process offers an alternative method of copper recovery to electrorefining and allows a range of Eh and pH conditions to be used to provide further discrimination of impurities. High purity copper powder was recovered by the Parker Process even in the presence of added impurities when the Eh and pH was maintained near constant throughout the refining step.

Jan 1, 1984

The ore is very 'refractory. It consists essentially of arsenical pyrites, iron pyrites, zinc blende, galena, antimony as sulphide and probably, in combination with galena, as Jamesonite, magnesium, and aluminium silicates with quartz. Some of the oxidized ore, of which there is very little, has a very interesting composition. A specimen shown to me by the ,general.manager, Mr. F. B. Stephens, consisted of hydrated arseniate of iron, orpiment, pyromorphite, lead oxide, with magnesium silicates and quartz. The ore found in the mine with a composition similar to this specimen was valued for gold contents at 60 oz. per ton. This ore is found as a small leader, which runs parallel to the main ore body, at intervals cutting through it.The ore is conveyed from the mine to the reduction works by means of a double road tram line. The mine is situated about rooo feet above the plant on a hill. The grade is so great (about I in 2) that the loaded trucks coming down are able to pullthe empty ones up, thus obviating the necessity of motive power for haulage. All that is necessary is two large grooved pulleys, fixed at the summit of the hilI, and provided with a rope-break for steadying the speed of the trucks down the hilI.

Jan 1, 1903

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981