Search Documents

By M Balamurali

In mining, grade control generally focuses on blasthole sampling and the estimation of ore control block models with little or no attention given to how the materials are being excavated from the ground. In the process of loading trucks, the underlying variability of the individual bucket load will determine the variability of truck payload. Hence, accurate material movement demands a good knowledge of the excavation process and the buckets’ interaction with the environment. However, equipment frequently goes into off-nominal states due to unexpected delays, disturbances or faults. The large amount of such disturbances causes information loss that reduces the statistical power and biases estimates, leading to increased uncertainty in the production. A reliable method that inferences the missing knowledge about the interaction between the machine and the environment from the available data sources, is vital to accurately model the material movement. In this study, a twostep method was implemented that performed unsupervised clustering and then predicted the missing information. The first method is Density-based spatial clustering of applications with noise (DBSCAN) based spatial clustering which divides the diggers’ and buckets’ positional data into connected loading segments. Clear patterns of segmented bucket dig positions were observed. The second model utilised Gaussian process regression which was trained with the clustered data and the model was then used to infer the mean locations of the test clusters. Bucket dig locations were then simulated at the inferred mean locations for different durations and compared against the known bucket dig locations. This method was tested at an open pit mine in the Pilbara region of Western Australia. The experimental results demonstrate the advantage of the proposed method in inferencing the missing information of bucket-environment interactions and therefore enables miners to continuously track the material movement.

Jun 22, 2022

By Y, Li Jianxiong, Hu Hua, Gu Desheng

After having briefed the technical and economical advantages of continuous mass mining in underground metal mines, the authors discuss the four stages of research and development of continuous mass mining in China. The four stages are: vibrating ore drawing in a stope, continuous mass mining in a stope continuous mass mining without rib pillars in an area and continuous mass mining in whole mine. The authors briefly review the research achievements of the first and the second stage; Combining the key national research project of the æNinth Five Year PlanÆ ù æThe experiment and research of continuous mass mining without rib pillarÆ, the authors introduce in detail the technological condition of mining, the design ideas of continuous mass mining, the design scheme of mining, the technology of mining. the equipment of mass mining, the chief research achievements and so on. The success of research of continuous mass mining without rib pillar indicates the arrival of the third stage of research. The introduction of continuous mass mining will promote the technology revolution of mining in China remarkably. The authors also point out that the development direction of continuous mass mining of the 21 century is continuous mass mining in whole mine, which is the fourth stage of research.

Jan 1, 2000

The sampling of a run-of-mine (ROM) ore with the objective of controlling the fundamental variance associated with the sampling step is a poorly understood subject. Finding the effective sampling constant by repetitive sampling to establish the variance between nominally identical subsamples of a given mass of the ore is a laborious, time-consuming and very expensive exercise. In this paper, the run-of-mine ore is modelled using three components: ore, waste, and relatively fine material which shows significant liberation of the mineral phase(s) carrying the target analyte. The expression for the sampling constant of the mixture is developed from first principles. The form of the equation provides insight into the factors that are important in controlling the magnitude of the sampling constant and hence the fundamental uncertainty associated with a given mass of sample. The controlling factors are shown to be the size distribution of the ore/waste mixture, the proportion of waste mixed with the ore and the extent of liberation and the size distribution of the liberated material in the finer fractions.

Jan 1, 2008

By P Hanna

Following the Busang fiasco, more detailed guidelines were appended to the latest revision of the JORC Code released in September 1999 (JORC, 1999). Although the definitions and terminology essentially remained unchanged, the additional information in the guidelines has highlighted a number of issues for consideration by geologists undertaking computer-based resource estimations. The three main issues are:Data Integrity û details such as drilling and logging techniques, sampling procedures, assay tests, site visits, data recording and aggregation methods need to be considered. Geological Interpretation û is the Competent Person applying the appropriate software interpretation to the deposit in accordance with the regional setting. Are the correct computer-based tools being applied and are they producing the desired result (without compromise) to the satisfaction of the Competent Person? Modelling Technique û the importance of the relevant experience of the Competent Person not only in regard to the geology, but also with respect to the modelling algorithms and resource calculation methods of the computer software system involved. At the end of the day, it is essential that the Competent Person undertake a reality check on the resource estimation itself. They should also check that the borehole spacing is in accordance with the level of continuity for each critical parameter (such as structure, grade, impurities, etc) for which the resources are categorised.

Jan 1, 2000

By Yaroshenko YuG, Bokovikov BA, Gordon YaM

Problems of the effect of the number of tuyeres and their parameters on the uni- formity of gas distribution are invest- igated with the use of the authors' devel- oped mathematical model of the movement of gases and materials in the blast furnace. It is shown that the improvement of uni- formity of gas distribution with an increase in the number of tuyeres has a damping character. An analysis of the errors of the specified assumptions of the hypothesis concerning the potentiality of the gas movement in the bed is carried out. It is established that the potential approach model gives good results with the determination of the discharge of gas and its stress field, but is not useful for the calculation of local velocities of gas in the raceway. The results of trials of calculation investigations of the dynamics of form- ation of the raceway and the voidageòfield in beds of burden materials are presented in the concluding part of the paper.

Jan 1, 1981

By Lu S, Jiang Y

The conventional transportation system in open pit, a to u.* itc:,~> truck., to carry the ore along the ramps. Normally, the transportation distance increases greatly as mining progresses deeper. A new approach to overcome the above disadvantage is to adopt a buried roadway by which ores is transported by conveyors from the mining area to the outside dump in the shortest distance so that the production efficiency is greatly increased. Maintenance of the buried roadway in a good working condition is the key factor that determines the success or failure of the proposed approach. This includes the determination of support load, types and structures of support and other related supporting measures. The crucial problem here is to effectively control the load applied on the buried roadway in a certain range that the ordinary support can stand. Based on the theoretical analysis, numerical modelling and physical simulation testing using equivalent material, this paper studies effects on control of the support load by adopting certain measures, for instance reinforcing the surrounding rock and placing the extendable layer between the support and a rock mass. Furthermore, the influence of the dynamic load induced by the movement of heavy vehicles on the stability of the buried roadway is also investigated.

Jan 1, 1995

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

By Davey KJ

Complex sulphide ores are characterised by complex texture of the valuable minerals. Any assessment of the performance of differential flotation circuits treating such ore should include analysis of the effects of poor liberation of the valuable minerals. Selected samples were taken from balanced size by size surveys of the flotation section of a concentrator treating an ore body containing fine grained galena and sphalerite in a matrix of iron sulphides which is mostly pyrite. liberation measurements were made using the QEM*SEM system on four or seven size fractions. The measurements indicated that less than 40 per cent of the galena and less than 60 per cent of the sphalerite in the flotation feed was liberated. The final concentrates were largely composed of composites of valuable minerals and iron sulphide however there was a small but significant fraction of liberated iron sulphide. Using the sized mineral flows obtained from the original balances and the liberation measurements, a satisfactory liberation balance was obtained. This enabled the effect of liberation on the flotation performance to be examined; not only for the entire circuit but also in the rougher, scavenger and cleaning sections. In the zinc circuit the effect of a regrind mill could be assessed. Recovery of galena in the lead circuit was limited by the recovery of composite lead particles. Recovery of liberated galena exceeded 95 per cent in all size fractions while the recovery of composite galena exceeded 85 per cent below 38 ¦m but fell sharply above 38 ¦m. Examination of the behaviour of the liberated and composite galena in the various sections of the lead flotation circuit revealed high recoveries of both liberated and composite galena particles in the roughing and scavenging sections but very low recoveries in the final two cleaning stages. Similar trends to those observed in the lead circuit applied in the zinc circuit although the performance of the liberated sphalerite also fell off at sizes greater than 38 pm in this case. Thus the zinc recovery was limited by the flotation of both the liberated and the composite sphalerite. The effect of regrinding was to increase the recovery of sphalerite mainly by reducing the amounts of sphalerite in less liberated sizes rather than by increasing the liberation of the sphalerite within a given size Fraction.

Jan 1, 1993

By N Van Buc, E Coroiu

The rapid socio-economic growth of Hanoi City coincides with a corresponding growth of the transport demand. Today, the transport in Hanoi is completely dependent on private modes of transport. Because of the lack of an efficient public transport system and the expected rapid increase in traffic volumes, the movement of people and goods in the urban areas of Hanoi will cause congestion in the present city transport network. The solution of the construction of new roads, or the widening of the existing streets, is very expensive in urban areas and usually causes many social problems due to the resettlement of people. From the point of view of the number of inhabitants, Hanoi City is now over one million. Above this number the international experience shows that the public transportation must be a mass transport system with large capacity, commercial speed and also independent as much as possible from the street network. According to the Hanoi Master Plan for 2020, the Hanoi urban population will be over 3.5 million persons. Also, in the next 15 years, the distances between centre-destination points will be doubled by comparison to 1995.

Jan 1, 1999

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

Mining is still a significant economic activity within the Hauraki District. The Martha project is particularly significant. Estimates are that in the order of 850 direct and indirect jobs are derived as a consequence of the Martha project within the Waikato Region. The Resource Management Act 1991 (RMA) is New Zealand's primary piece of environmental legislation. It sets out to provide the framework for the control of the use, development and protection of almost all physical and natural resources. Minerals are excluded from the sustainability requirements of the legislation but as mining invariably involves the use of land, all the other elements of RMA apply. The Council's role in dealing with mining changed with the introduction of RMA. It became responsible for administration of those matters that fell within the functions set out in section 31 of the RMA in respect to existing authorisations. Mineral development needed to be considered in the development of the District Plan that the Council is required to prepare. Implementation of the Act has been a challenge for not only local government but for many industries and resource users since it came into force in 1991. There have been, and are, differing views on both the way it is administered and its intent. The Hauraki District Council has been at the forefront of some of the challenges that are a consequence of the Act. Its reactions to these challenges have been consistent. It treats mining in the same why it treats any other industry. At times this approach has not been understood and without challenge from sections of the community.

Jan 1, 2000

By T Higuchi, K Fukada, K Takehara, Y Iwami, S Fujiwara

Following the Paris Agreement adopted in 2015 and the SDGs, reduction of CO2 emissions has been taken up as an issue worldwide, and the steel industry, which has a particularly large emission, is required to significantly reduce it. Most of the CO2 generated in the steel industry is generated from the ironmaking process, due to the use of coke and its raw material coal in the ironmaking process. JFE Steel Corporation has been considering the use of hydrocarbon-based gaseous fuels and liquid fuels as a partial alternative to coke breeze used in the sintering process since 2006, immediately after the Kyoto Protocol came into effect in 2005. In a laboratory study, a pot test was used to investigate the effect of the type of fuel, its amount and its injection method on the heat pattern in sinter bed. As a result, the authors developed a technology, in which a predetermined amount of gas fuel or liquid fuel was injected from the surface of sintering bed to extend the holding time of 1200°C or higher at which liquid phase sintering occurs in the layer, to improve the sinter strength while reducing the amount of coke breeze. The authors succeeded in putting this technology to practical use using hydrocarbon-based gas fuel in 2009 and achieved a maximum annual reduction of 60 000 tons of CO2 per sintering machine. In this report, the authors introduce the results of laboratory studies on the use of various energy sources, the practical application of the technology for injecting hydrocarbon-based gaseous fuel into the sintering machine, and the operational results.

Nov 8, 2021

By Wu Y, Qu Q

The Central Coal Mining Research Institute has developed the MAE acoustic emission monitoring system, the BD4-1 portable acoustic emission monitor and the MRB rock burst monitoring system. In the MAE system there is an IBM-PLAT, a receiver and 16 channels and the investigating range is 100 m. The main functions are detecting acoustic events from the working faces, periodically making statistics, prints, displays and storing of the results, and performing the off-line process such as drawing the curves of acoustic activity. The BD4-1 instrument has four channels, it works for more than 24 hours continuously, and keeps the data for more than 30 days after power tum-off. The BD4-1 is suited to the monitoring for a long or a short time as a fixed point where the system is invalid, especially to the monitoring of the acoustic activity promoted by the blasting. There is an IBM-PC/AT, a receiver and 16 channels spread 10 km in the system MRB. The system could on-line collect microseismic events throughout the whole mine, calculate the source location and the energy, and off-line draw the seismic activity draft of time-based or distribution in space. In practice, the forecasting is successful by using the acoustic emission and microseismic monitoring system and the portable instrument.

Jan 1, 1991

By Kuzmitch O, Morozov A

The main direction in the mechanisation in the mines of the Donbas and the USSR is long-face technology with complexes on the base of hydraulic supports. On the base of the 30 year old experience of exploitation of the coal clearing systems the serious data about the behaviour of the contained rock, display of underground pressure 'on longwalls and preparatory workings have been accumulated. Exploitation works in mines of the USSR are carried out at different depths: from 1000m to 1200m. There are 26 mines in Donbas, which exceed the depth of 1000m. It is the mines of Donbas, where is a rich experience of the exploitation of coal seams in various conditions. Besides, there are wide variations on the factors of the extraction thickness, depth of seam, angle of dip, occurrence of gas dynamics and others. In many scientific establishments, and in Donetsk Polytechnical Institute also, there are scientific research/results, which can be of interest for the coal mining countries.The volume of coal mining from longwall system-mechanised walls in Donbas became stable at the end of the 70s at level of 70 percent. All the efforts to increase this level have not given any notable results, not saying about the technical-economical data, which gradually deteriorate. It shows that positive progress in using the technology for the long walls is over and it is necessary to find new ways of mechanisation of coal winning.

Jan 1, 1991

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

By A Gustafson, G Shekhar, P Boeg-Jensen

The amount of material extracted from each blasted ring in sublevel caving mines is vital when deciding the overall mine production target. The orientation of the production drifts is normally perpendicular to the strike of the orebody, and rings are blasted from the hanging wall side to the footwall side in a retreating manner. For an inclined orebody, a given ring will contain different amounts of material based on its relative position along the production drift. This layout creates a distinctive problem with respect to the extraction ratio optimisation along the axis of the production drift. This paper describes the current drawpoint control strategy practiced at LKAB and presents the variation of drawpoint performance parameters along the production drifts. It uses automatically generated data from a bucket weighing system that measures tonnage drawn per bucket, and it classifies the blasted rings into four zones based on their relative position along the production drift. It considers the loading procedure for blasted rings at Kiirunavaara mine and analyses the variations in drawpoint performance along the production drift. The paper finds that although the current draw control strategy is sensitive to ring position along the drift, it could be modified to optimise the final extraction ratio.CITATION:Shekhar, G, Gustafson, A, Boeg-Jensen, P and Schunnesson, H, 2016. Draw control optimisation along the production drift in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The specification for tender nominated the requirements for ore hoisting and servicing; this showed that one common duty winder could be selected. Foliowing the design of the shaft layout, the merits of fixed or rope guides were compared and the latter selected.The specification called for the supply and installation of the complete hoisting system. Construction of the winder tower and shaft bottom steel work had to proceed while mine development was in progress using the sinking winder and headframe. Guide ropes, winder ropes, and the sky shaft were installed in the shortest possible time, and as the shaft was not equipped with ladder-ways, a second means of access had to be provided.Very few problems were encountered witll the commissioning of the winder, and in the first 2 years of operation the only significant modification was to the circuitry associated witll the moving access platforms.Hoist rope tension checking and adjustment are simple, and non-destructive testing has shown no deterioration of these ropes. The operation of the balance ropes has been very satisfactory but cleaning presented problems in the early stages. Guide ropes have been trouble free and require minimum attention.Normal wear on the PVC rope groove inserts on the winder drum has been negligible.Since the commissioning on fully automatic ·control, the winder has operated with very few, minor delays.

Jan 1, 1969

By J G Reid

In the period since 1989 the Yabulu Nickel Refinery of Queensland Nickel has undergone a transformation both in terms of the nickel laterite ore feed and the refined nickel product. These two changes were mutually supporting, as will be shown in the following paper. It had been realised since the early-1980s that the Greenvale orebody would be exhausted by 1992. Consequently planning had been in progress throughout the 1980s for the importation of overseas ore as a replacement for the Greenvale ore. The existence of extensive lateritic ore deposits in New Caledonia and Indonesia made these locations the natural focus of attention. With the three Japanese ferronickel smelters sourcing their nickel garnierite ore feed from these locations it was relatively easy for the miners to supply the overlying limonite ore to Yabulu. This limonite ore was previously discarded as waste. The Yabulu refinery now receives about 85 per cent of its ore from these two overseas sources. The transition from Greenvale ore to imported ore occurred gradually between 1989 and 1993. It was during the ore importation planning stage of the mid 1980s that Queensland Nickel commenced the technical investigation which led to the ammoniacal solvent extraction (ASX) plant installation and the product change from nickel oxide to nickel metal.

Jan 1, 1994

Thrusting is well documented in the Finisterre/Sarawaget moun- tains, the Kainantu-Waf district and in the Highlands between the Kubor Anticline and the Ramu Valley, Papua New Guinea. The thrusts trend NW and involve rocks ranging in age from Permo-Triassic to Plio-Pleistocene. Evidence from the Finisterre/ Sarawaget mountains demonstrates that a major phase of thrust- ing commenced in Pliocene times and continues today. Palaeostress analyses is a sensitive technique for assessing the kinematic history of faulting. The picture gained from the Finisterre/Sarawaget mountains, the Kainantu district and be- tween Kundiawa and Keglsugl is simple, involving a north to northeast ol. Local complexities between the upper Chimbu Valley and Brahmin indicate extension on a NW-N trend. The simplicity of this anlaysis, which accords with seismic and geo- detic strain data, shows that the major faulting in Papuan Orogen is no different from that in the Papuan Fold Belt; that the Papuan Orogen and the Papuan Fold Belt together form a young thrust- fold complex; and that such structures as the Kubor Anticline may be fault-bend folds. Recognition of the obduction of the Finisterre/Sarawaget reef/ volcanic complex over the Australian plate, the gas seeps in the Ramu Valley and foothills of the Finisterre/Sarawaget Mountains, oil seeps in the Goroka and Kundiawa regions, and our interpre- tation of the PNG Orogen as part of the Papuan Fold Belt indi- cates unexpected probability that the PNG Highlands are pro- spective for hydrocarbons.

Jan 1, 1997

To follow the development of the central crushing plant it is necessary briefly to outline the history of the Lake View and Star Limited. This Company, when first constituted, took over the properties of the Lake View Consols, Hannan's Star, and Chaffers Gold Mines.The Company then treated the ore won from these leases at two dry crushing, all-roasting plants, situated adjacent to each other on the site of the present Chaffers Treatment Plant that handles all the ore won by the Lake View and Star Ltd.SUbsequent to the initial union of the three companies mentioned, the Ivanhoe Gold Corporation and the Golden Horse Shoe Ltd. were absorbed. Still later, and after the original crushing plant was erected, the Associated Gold Mines of Australia were purchased.A very extensive development policy was adopted by the Company's management in the late 1920's, and as the underground programme progressed, it became eVident that a large treatment plant would be required. Wet milling of the ore, followed by flotation, was considered desirable, and the necessity of a central crushing plant capable of producing a feed that could be handled by the wet ball mills attached to it was obvious.At this time, each of the properties absorbed had its own crushing station, situated adjacent to the respective...

Jan 1, 1948