Search Documents

The title of this paper implies, and the text explicity states, that Sen and Spottiswood (1984) have found a new mineral species related to geocronite and jorganite. I believe that there is inadequate justification for this claim.The X-ray powder diffraction pattern reported by the authors exhibits a close similarity to that of geocronite, as stated by the authors, which suggests a close structural relationship at the very least. It is therefore reasonable to recalculate the results of the microprobe analysis reported by them to atomic proportions on the basis of the geocronite formula. This calculation, whether based on the formula used by Sen and Spottiswood (1984), or on one derived from a crystal-structure analysis (Birnie and Burnham, 1976), namely Pb18 (Sb, AS)11S46, with a total of 86 atoms, gives the results shown in Table 1.

Jan 1, 1985

By G Ma, L Qi, J G. Shellnutt

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Emeishan large igneous province (ELIP) of SW China is host to magmatic Ni–Cu–(PGE) sulfide and Fe–Ti–V oxide deposits which contain economic to subeconomic concentrations of precious and base metals. The formation of a given deposit-type (ie sulfide versus oxide) is thought to be related to the type of parental magma (ie high-Ti versus low-Ti) and the subsequent processes (ie fractional crystallisation and sulfide segregation), which allowed for metal enrichment.We examined the PGE of Baima and Taihe oxide-bearing layered mafic intrusions from the ELIP (Shellnutt, Ma and Qi, in press), and compared them with the nearby Xinjie and Hongge intrusions as well as with the Emeishan flood basalts. The PGE results for the two intrusions are contrasting. The Baima gabbroic rocks are almost PGE-barren (SPGE < 4 ppb) whereas the Taihe gabbroic rocks are variable, but generally much higher in PGE concentrations (SPGE < 2 to ~300 ppb), although the gabbros from both intrusions are enriched in platinum-subgroup PGE (PPGE = Rh, Pt and Pd) relative to iridium-subgroup PGE (IPGE = Os, Ir and Ru). Cu/Zr, Ni/Ir, Y/Pt, Cu/Pd and Ni/Ir systematics suggest that the Baima rocks were derived from a relatively evolved, mafic, S-undersaturated parental magma that was affected by earlier sulfide segregation. In contrast, the Taihe rocks record evidence of both S-saturated and S-undersaturated conditions and that the parental magma was likely emplaced very close to S-saturation. Through comparison of the PGE contents in the Emeishan flood basalts and the Emeishan oxide-bearing intrusions, we provide a self-consistent model for ELIP that the PGE budget in a magma is not strictly controlled by magma series (high-Ti versus low-Ti), but very much by crustal contamination.CITATION:Ma, G, Shellnutt, J G and Qi, L, 2015. Platinum group elements in the Baima and Taihe Fe-Ti oxide-bearing gabbroic intrusions of emeishan large igneous province and problems on propensity of magma series for sulfide- versus oxide-dominated deposit types, in Proceedings PACRIM 2015 Congress, pp 303–310 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

By Y H. Zhu, X X. Tang, Y C. Yin, M L. Xing

Based on the stiffness theory, the stiffness difference and energy supply of surrounding rocks are important inducing factors for strain burst. However, due to the lack of multi-level low stiffness testing machine, there are few experimental studies on rock failure mechanisms under the influence of loading stiffness. This paper introduced a self-developed rock testing system with changeable stiffness. The main testing machine of this system is a combined structure of inner and outer frame. The change in the loading stiffness is achieved by using a stiffness servo control system to control the energy accumulation in the inner frame. The tests of the sandstone specimens under three different loading stiffnesses in the testing system showed that the loading stiffness did not significantly affect either the uniaxial compressive strength or the Young’s modulus of the rock. However, the post-peak stress-strain curve of the rock became smoother and steeper when the loading stiffness was decreased, and the stress drop rate increased. It is shown that the stress drop rate had a power function correlation with the loading stiffness. After the peak load, the inner frame of the testing system rebounded several times at high speeds. The magnitude of the instantaneous rebound speed and the rebound duration increased with the decrease of loading stiffness. Both the mean rebound velocity and the total rebound deformation had power function correlations with the loading stiffness. The loading stiffness has limited effect on the energy storage and energy dissipation characteristics of the specimen, while the released energy of the testing machine increases as the loading stiffness decreases, which is the key factor affecting the failure mode of the specimen. According to the test results, a rock burst mechanical model considering the stiffness is established, and the energy supply mechanism of rock burst is quantitatively explained.

Nov 29, 2022

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By I A. Lamb

The Melbourne City Link Project has two tunnels, the Domain and Burnley Tunnels, which have been constructed by Transfield Obayashi Joint Venture (TOJV) under a design and construct contract. The two tunnels are located essentially under the Kings Domain, the Yarra River and, in the case of the longer Burnley Tunnel, under the inner suburb of Richmond. The Burnley Tunnel is 3.5 km long and reaches a depth of 65 m at the central Swan Street Shaft, the invert being at RL -60 m. The Domain Tunnel is 1.6 km long, with the invert reaching RL -20. The tunnels were driven, for the most part, in the siltstone and sandstone of the Silurian Age Melbourne Formation. Construction aspects of the driven tunnels as related to the engineering geology have been described by Hutchison et al (1998). The Silurian bedrock is a fractured rock aquifer that is connected to overlying alluvial aquifers. Excavation of the tunnels allowed temporary groundwater inflows which substantially de-pressurised portions of the various aquifers. This de-pressurisation provided the potential to accelerate on-going secondary consolidation rates of the Holocene Aged Coode Island Silt (CIS) and the older Quaternary Fishermens Bend Silt (FBS) deposits, in areas where these materials directly overly the aquifers. As a large portion of the urban area of South Melbourne and the old river course of the Yarra River contain extensive CIS deposits, and were within the drawdown influence of the tunnels, the management of the hydrogeological regime was very important. The permanent design of the tunnels comprised drained and undrained sections (a partially tanked design) which, along with some permanent recharge, provide long-term protection against the possibility of accelerated settlement rates. During construction TOJV implemented a comprehensive groundwater management plan to deal with issues related to the temporary drawdown of the aquifers and the temporary acceleration of settlement. This paper describes the hydrogeological regime, the effects of the tunnelling, the monitoring programs, the extensive temporary recharge system, and the consultation program that TOJV utilised to manage the hydrogeological issues.

Jan 1, 1999

This paper examines the impact of the time value of money on the location of mining facilities, as examplified by a central processing plant serving several mines. Three approaches, the Euclidean-Distance Approach, the Gravity Centre Approach, and the Rectilinear-Distance Approach, commonly applied to a single facility location problem were employed in the study. The objective function in all three models was the updated value of the following three costs influenced by the processing plant location and defined within the framework of the continuous model of value representation and the continuous interest rate convention: I. the costs of transporting the useful mineral from the mines to the plant, 2. the costs of constructing the transportation links between the mines and the plant, and 3. the costs of maintaining these links over time. Results of the study show a substantial impact of the time value of money on both the processing plant optimal location and the opportunity cost of neglecting the time value of money in the locational considerations.

Jan 1, 1995

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Hoisting ropes are constructed of wires and strands positioned helically around the axis. This helical positioning causes that, in the rope loaded at the end with the weight Q, the longitudinal displacement u, axial force P, torsional displacement v and constant torsional moment M are generated. More over, the proper weight of the rope q gives the force acting along the axis of the rope. This force changes its value from 0 at the bottom to qL at the top. This force gives, along its length, a variable torsional moment making the rope rotate. During the movement of the conveyance downwards the falling part of the rope rotates, which makes it untwist on the section up to the half-depth of the shaft and twist on the other half-depth. As the result, the twisting lay of the rope changes increasing in the upward direction and decreasing downwards. The angle of twist of the strands changes in an apposite way. When moving upwards, the uplifted rope does not twist and retains its state of deformation up to the moment when it passes over the pulley. Next, the cycle of untwisting and twisting repeats during the movement of the other conveyance downwards. This phenomenon is known from mining practice. It was also analysed, in the works of Glushko (1966) and Popowicz (1963).

Jan 1, 1995

By P Ritchie, E H. Briese, N A. Currey

Kidston Gold Mines, located in semi-arid North Queensland, Australia is currently in its closure phase. Highly innovative and comprehensive rehabilitation strategies were employed at the site, including the direct revegetation of the surface of the tailings storage; the construction of a tailings sediment entrapment pond; the construction of a spillway to drain large rainfall events from the surface of the tailings; the construction of store/release covers over the tops of the waste rock dumps; the sheeting with oxide waste rock of the waste rock dump slopes; the partial back-filling of the initial Wises Hill Pit with waste rock and thickened tailings produced from the subsequent Eldridge Pit; the partial flooding of Eldridge Pit following the end of mining; and the construction of wetland systems to treat contaminated tailings and waste rock dump seepage. These closure strategies involved the careful consideration of water management. Specific water management issues included understanding the water balance of the tailings dam; the operation of the tailings dam sediment entrapment pond and spillway; understanding the water balance of the store/release waste rock dump covers; the importance and sustainability of vegetation on the tailings, store/release waste rock dump covers, and on the sheeted waste rock dump slopes; the level and quality of water in the partially flooded Eldridge Pit; and the treatment of contaminated seepage in the constructed wetlands. The seasonal and highly variable rainfall experienced in this semi-arid climate posed a number of challenges for the management of water on the site post-closure. The paper details these challenges and highlights how they were resolved over the period leading up to and following the end of mining.

Jan 1, 2003

By Bogar D. V

Often dewatering of coal tailings is inhibited by the presence of clays, making it difficult to obtain a high concentration, handleable coal tailings. The net result can be a low concentration, chocolate mousse-like tailings which poses significant sedimentation problems in a tailings dam and represents a significant environmental problem. This paper examines the coal tailings from a Hunter Valley colliery where the tailings properties are influenced significantly by the presence of montmorillonite clay. The influence of the calcium ion on the rheology and sedimentation/compression behaviour of coal tailings . containing montmorillonite already dispersed in water was investigated and revealed that very little improvement in the properties is achieved through the coagulation. The preliminary investigations also indicated that the properties of the tailings were dominated by the presence of the montmorillonite clay. Thus investigations were carried out on the clay alone in water. Investigations into the effect of dispersing samples of the clay alone in water and then coagulating with calcium compared with dispersing the clay directly into calcium ion solutions at the same calcium concentration showed huge improvements in the rheology, compressibility, sedimentation rates and sediment solids concentrations for the second dispersion method, which can be called controlled dispersion. The sediment volume fraction solids improved by more than a factor of two by controlling the dispersion of the clay. The reason for the improved properties lies in the suppression of the initial swelling of the clay, which is initially in the sodium form, thus maintaining the parallel orientation of the platelets that is present before wetting. While swelling is being suppressed, ion exchange occurs with the calcium which results in permanent swelling suppression. In the uncontrolled dispersion case where swelling is uninhibited, the clay is allowed to break up and despite the powerful coagulating nature of the calcium ion, the random orientation of the high aspect ratio clay platelets inhibits effective coagulation. Results indicate that the initial electrolyte concentration of the washwater in a coal washery is the critical factor controlling the dewaterability of clay tailings and the handleability of the dewatered product rather than the actual act of coagulating with the calcium ion. The results presented are of clear practical significance and indicate how coal tailings problems where clay dominates the rheology can be improved considerably by knowledge of the surface chemistry.

Jan 1, 1995

The purpose of this paper is to discuss briefly the problems encountered in designing and sinking No 7 shaft, and to present the methods employed in the operation.The illustrations accompanying the paper show the details of the construction of the equipment used in completing No 7 shaft, consequently the descriptions appearing in the text are brief outlines only. Mineral leases Nos 7 and 8, held by the Broken Hill South Limited, comprise an area of 69.5 acres. The length of the holding is approximately 2500 ft.The western orebodies, which are the main producing masses, enter the property at the northern bonndary. Generally, the dip of the orebody is to the west, and the pitch to the south, but local variations occur and even a reversal of pitch has been noticed. The angle of dip is approximately 70 degrees and the angle of pitch 45 degrees.

Jan 1, 1932

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991

By S Li, Y Lei, X Wu, C Ma, W Q. Zhang

The failure of roof of thin bedrock working face under loose aquifer in a coalmine can lead to water-sand inrush disaster. Based on the accident of water-sand inrush in 30108 working face of a mine in Shaanxi province, China, the mechanism of water-sand inrush is theoretically analysed. The process and critical conditions of water-sand inrush in working face are reproduced by numerical simulation where the bedrock thickness is 20 m, the clay layer thickness is 40 m and the mining height is 6.5 m. The study found that under the condition of thin bedrock and thick clay layer, the characteristics of the clay layer have a significant inhibitory effect on the development of the fractured zone, and the development of the water-conducting fractured zone is incomplete and insufficient. However, in the process of continuous mining of multiple adjacent working faces, the strength of the clay is gradually reduced by the influence of mining and the erosion of water, and the height of the fractured zone is gradually increased. In the subsequent mining process of the working face, the roof is more likely to be cut-off and lead to water-sand inrush. From the initial failure of the clay to the final crack directly through the surface, the shear strength of the clay is reduced by about 52 per cent. Further simulation found that in addition to the characteristics of the clay layer itself, the main factors affecting the water-sand inrush in the working face caused by overburden failure also include the difference in bedrock thickness and strength, and the difference in coal seam mining height. With the increase of bedrock thickness, the development height of the fractured zone increases gradually with increases of bedrock thickness when the cutting failure of overburden rock no longer occurs. With the increase of mining height, the height of water flowing fractured zone also increases, but the cracking ratio gradually decreases. Therefore, it’s of great practical significance to systematically study the mechanism and critical conditions of water and sand inrush in mines and the main influencing factors for preventing similar accidents in mines with similar conditions.

Nov 29, 2022

By Horiszt G

his report is going to point to that the effect of the mining dewatering on the area of Transdanubian Mountain Range has reached a phase when the cost of dewatering and providing damages can seriously jeopardize a profitable mining operation. Up to 60s the interest of mining had been dominant only, but since the begining of 80s the conceptions of industrial development and the value of enviroment protection have been changed. The natural karstwater balance of the TMR can be presented (Figure Land 2.) and the present situation of it points to that the descharge has exceeded the reacharge in 50 %. During the past 10 years the decreasing of the stored karstic water resourches was 1.1 km . The decreasing of the spring yields reached 80-82 % of the natural ones. (Figure 3-4.). Conservation of the present discharge may lead up to the totaly drain of the karstwater regime. A computer aid control system had been to develop by the bauxite mining and using of it the yield of dewatering decreased and a moderate rising of the water table has started since 1986. A recunstruction was made at the biggest thermal-medicinal lake its springs have had their source in 40 meter depth inside a spring cave at the bottom of the lake. Earlier the spring yield decreased due to the dewatering activity of mines. As a result of using of the CAC system and the providing works at the thermal sprino,the karstwater balance has got in the state of equilibrum, the first cost was decreased and spring yield was increased and the enviromental limits were adverted from the way of mining.

Jan 1, 1988

It is a pleasure and a privilege to be with you for the Annual Conference of The Australasian Institute of Mining and Metallurgy.The inaugural meeting of The Institute was held in Adelaide in April, 1893. Through the kindness of your President, who passed on to me several publications concerning The Institutute I have been able to glance back over the eighty years in which The Institute has served both the profession and Australia.In that record, many names of great distinction caught my eyes. When one reads the list of past presidents of the The Institute since 1893 and the list of those to whom The Institute Medal has been awarded, one reads the headings of a biographical dictionary of the Australian mineral industries. Many famous names are there-men from the great mining companies, engineers, scientists, metallurgists and geologists. Simply to read the names is to recall great enterprise and great achievement. Going over those names one hears the echoes of the inspiring story of the establishment of the Australian steel industry, the electrolytic zinc inq.ustry, all the major developments in the mining of coal, gold, copper, silver and lead, the treatment of difficult ores, the geological exploration of a cqntinent, the discovery of uranium, bauxite, petroleum, nickel, the establishment of the alumina industry and finally the mammoth earthmoving operations of today. The list of names is a chronicle of great men who did a mighty work. They stand like milestones in the progress of a nation.When one reads further and runs down the titles of some of the papers published in the Proceedings of The Institute even a layman like myself can appreciate the dramatic developments in mining and metallurgy that have transformed the whole practice of the mineral industries in our land. Australians have made some notable innovations and discoveries both in mining techniques and in the processing of ores. The history of mining is not only a story of the discovery of the mineral resources of this continent but of adventurous steps taken to perfect new ways of mining the ore and extracting the metal.I read with great admiration the presidential address given by Sir Maurice Mawby in 1968 and wa...

Jan 1, 1973