Search Documents

Analysis of Electrostatic Separation for Rutile Cleaning Duty Using a Plate Electrode Assisted High Tension Roll Separator A plate assisted electrostatic high tension roll separator has been used for the removal of impurity mineral grains from a rutile rich product stream. A laboratory study and a subsequent production study explored the effect of machine conditions with a view to the optimisation of the separation performance of the separator. The performance requirement was that the TiO2 grade in the non-conductor stream was to be less than ten per cent whilst at the same time the ZrO2 grade in the conductor stream had to be less than 0.5 per cent at mass recoveries of greater than 90 per cent to the conductor stream and less than 5 per cent to the non-conductor stream. Mineralogy data was utilized to determine the feasibility of achieving the production targets with the feed under study. Since the feed stream mineralogy was dominated by rutile, leucoxene and zircon, it was possible to use an approximation to the actual mineral assemblage as well as the raw X-ray fluorescence data to understand the separation duty of the Carrara machine. Since there were four conflicting criteria used for the performance requirement, an index was devised that incorporated all the requirements simultaneously. This new index was the sum of the squares of the difference between the achieved and desired values, weighted with respect to the variance of each variable. If the desired value for a particular criterion had been met its contribution to the sum was set to zero, no matter how well the criterion had been met. For the production machine the strict requirements were almost achieved. As expected, the achievement of the target performance was dependent of the feed conditions at the time of measurement. This paper reports the results of this study.

Sep 13, 2010

South Africa is the world's largest producer of gold. The survival of its gold mining industry is dependent, to a large extent, on the successful implementation of new mining technology which reduces the operating costs. Gold mines of the country have a record of a high operational cost per tonne of rock excavated. The geology of the gold-bearing rock, in addition to the mining depth and the gold recoverable grade, profoundly affect the profitability of the industry. Among the other mining operations, drilling and blasting take a fair share of the mining cost. It is therefore proper to implement a dynamic approach of technological review aimed at combating the escalation of mining costs. Over the years, the industry has moved away from labour intensive activities. Mechanised operations are introduced where possible. Management techniques are oriented more towards better utilisation of human resources and machinery so as to enhance productivity in the stopes. This paper addresses the issue with particular reference to blasting operations in the stopes of deep gold mines. It reviews the conventional drilling and blasting techniques. It outlines some innovative changes brought about in the course of recent years with the aim of optimising productivity and the stope efficiency in particular. It focusses on the peculiarities of the blasting technology in deep mines. It discusses the issue of interaction between the high stress fields underground and the blasting generated stresses on rock fragmentation, as well as their impact on the remaining excavations. It anticipates the concept of the new technology of selective blasting in stoping. Finally it puts forward the crucial role played by management of the human factor underground.

Jan 1, 1995

Longwall mining originated in the early 18th century in the county of Shropshire in England, where it was known as the longway method. Its name implies the extraction of the seam over a long continuous length or wall of exposed coal. Until the late 19608 and early 1970s the use of the longwall system with a few exceptions was confined to the United Kingdom and Europe. It was not until the early 19708 that the highly productive longwall faces we now know, were developed and the application of the longwall system extended to Australia, South Africa, United states of America and other parts of the world. The modern longwall face has three major components, namely: +         the machine to break and load the coal +         the face conveyor; +         and a system of roof support.   This paper reviews the development of longwall mining technology. The parameters directly influencing the production 'of a modern longwall face are considered, as are the possible constraints to the further development of the longwall system.

Jan 1, 1991

By P Rowe

New Zealand Steel's Taharoa titano-magnetite mine, south of Auckland, set two national load records when it transported around 2000 t of mining equipment three kilometres overland on time, under budget and without safety incident. It was the first time in New Zealand that four platform trailers were assembled end-to-end to transport a load. It was also the first time that a single load of 1000 t was transported on platform trailers. The need for the relocation of all equipment was realized five years ago. It took two years of planning and specialist advice to relocate the mine's 250 t dredge, 500 t surge bin, 1000 t concentrator plant and ancillary equipment from the Southern Mining Region across a specially designed haul road to the Central Mining Region. The project was carried out during a six-week shutdown in early 2001. Two dry docks were constructed, one at each end of the relocation route. The equipment was floated into a dismantling pond that was interconnected with the dry dock in the Southern Region. Through pumping, the water levels were controlled to allow transfer of the separated units from the dismantling pond into the dry dock. Once drained, sets of self-elevating platform trailers were used to transport the main units, one at a time, between the dry docks. Five prime movers were used to pull the loads. At the receiving end, the units were off-loaded in a dry dock interlinked with ,the first mining pond. The equipment was relocated because the reserves in the Southern Mining Region were mined out. A natural watercourse û the Wainui Stream û defines the northern boundary of the Southern Region and the objective became to relocate the mining plant to the other side of the stream and re-establish in the Central Region. The project team selected the trailers as the most effective means of transporting the equipment, particularly given the non-invasive means of crossing the Wainui Stream. Negotiations with prime contractor Tranzcarr Heavy Haulage Ltd commenced in mid-2000. The remainder of 2000 was spent in developing concepts with the contractor, detailed designing, preparing the dry docks, haul road and initial mine plan for the Central Region. These activities occurred with no conflict to the normal site production.

Jan 1, 2001

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

The first part (lH of this work dealt with the process of recrystallization of single crystals of lead after deformation by creep, as revealed by macroscopical examination. It was shown that when recrystallization commenced, a crystal, termed the primary crystal, started to grow at the edge of the specimen and extended into the body of the specimen along the slip planes. At some stage during the growth of this crystal, other crystals appeared at the boundary of this first crystal and fragments of the parent crystal. From thispoint, recrystallization was accelerated with relatively rapid necking down of the specimen until fracture occurred.All those crystals formed after the primary crystal were given the term secondary crystals. In the present paper is given a detailed account of the orientations of the primary and secondary crystals.EXPERIMENTAL METHODThe size of the test pieces and the manner of loading were given in the previous paper (1). X-ray back reflection photographs were taken of the individual primary and secondary crystals and from them were determined the orientations. The path of the X-ray beam was perpendicular to the surface of the creep specimen.In view of the large number of photographs needed, gold...

Jan 1, 1940

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

The Australian bulk explosives industry has matured significantly over the last five years and it would appear that the rest of the world is following suit. This maturity is characterised by the technical sophistication of modem bulk explosives, an increase in the technical competence of the explosives consumer and a greater openness in the debate on the quality and performance of explosives. The principal mechanism by which these advances have been made is undoubtedly commercial competition in the market place although a new element, technical competition between manufacturers and independent professionals, has and will continue to play an important role in the development of the industry. The relationship between the explosives manufacturer and consumer is necessarily both complementary and competitive. This paper identifies the need for the consumer to take a more prominent role in the critical analysis of the performance of explosives and to use his commercial influence to direct explosives manufacturers at least in the direction required for the future technical development of the industry.

Jan 1, 1990

By Kim YC

An alternative development drilling strategy to the one currently in use at an open pit mine was investigated using geostatistics for a portion of the pit. The massive orebody, the 3-D nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy. Rather than using confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from the study showed that a total of 50 diamond drillholes (DDHs) rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. The paper also emphasizes the importance of particular objectives being used in development drilling and how they influence the "optimal" placement of the development drillholes.

Jan 1, 1986

By T Akiyama, J A. de Castro, H Nogami

Blast furnace is a countercurrent moving bed reactor that produces pig iron from iron bearing materials like pellet, sinter or lump ore. The furnace has cylindrical shape and the lump solid materials are alternatively charged onto the top of the furnace. Hot air is introduced through tuyeres that are set on the lower furnace wall. Auxiliary fuels (pulverised coal, oil or natural gas) and raw materials (fine ore or fluxes) are injected into the furnace with blast air from the tuyeres. In front of the tuyeres, coke particles react with oxygen in the blast air and generate carbon monoxide. The hot reacting gas heats up the lump solids and reduces iron oxides in the upper furnace. In the middle height of the furnace, the reduced iron and slag are fused by the combustion heat and form the cohesive zone. The molten iron and slag that are generated in this region trickle down through the packed bed of coke particles and flow into the bottom of the furnace. Therefore, the flows of gas, lump solids and liquids exist at the same time in the lower part of the blast furnace.

Jan 1, 2000

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

By D Asahina, T Endo, H Hosono, T Takemura

Changes in the stress field around faults due to the excavation of underground space or the extraction of underground resources induce fault reactivation. To understand the mechanism of fault reactivation, it is important to observe the deformation and sliding processes of the asperities, which is regionally contacted areas at the fault planes. In the laboratory, triaxial compression tests are commonly conducted to reproduce the stress conditions around faults and study their mechanical behaviours. The conventional measurement devices for triaxial compression testing (eg load cells, local deformation transducers, and piezoelectric sensors) uses sensors to measure changes in the physical properties of rocks, but the direct visual information for the sample condition inside the pressure vessel is limited and can only be estimated from the sample after the experiment. We recently developed a direct visual measurement system to observe the slip behaviour of rocks from the inside of the pressure vessel of a triaxial test apparatus. This paper introduces this visual measurement system and presents some preliminary experimental results. The visual measurement system consists of a steel housing with a built-in commercially available digital camera. The triaxial compression tests were conducted to visually observe the sliding behaviour of the pre-cut specimens and to measure its behaviour through the digital image correlation (DIC) method. The captured images and the DIC results show the displacement field of the specimens for different confining pressure. We verified the sliding behaviour and the failure at/around the triangular asperity under at different confining pressure.

Nov 29, 2022

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By S W. Kingman, D Whit, I S. Lowndes

The use of compressive crushing equipment such as gyratory crushers within minerals processing plants can potentially generate large quantities of dust. Remedies to this problem include the retrofitting of shrouds, enclosures, local exhaust ventilation (LEV) systems and water suppression systems. The single or combined application of these systems must be optimised to ensure they operate efficiently. It is desirable that the future design planning of such facilities include integrated dust suppression and/or removal systems to ensure material delivery rates are maintained and the welfare of the workforce is protected. The characteristic release of dust and the disturbance to the surrounding ventilation airflow is investigated by the construction and solution of computational fluid dynamic (CFD) models validated by data obtained from scale experiments. A 3D computational model was constructed using the FluentTM CFD software to represent the background ventilation regime within an underground crushing installation. The falling ore is represented as a continuum granular fluid falling under gravity from the raised bed of the dump truck. Transient path lines are computed to simulate the updraft airflow generated by the tipping process and indicate the dispersion path of any entrained dust. The relationships between the falling ore material, the displaced air and the shear induced flow are determined by an analysis of the computed volume/mass flow rates predicted across the crusher opening. An analysis of the airflow patterns predicted by the CFD simulation models indicates strong shear flows induced between the tipped material and the surrounding airflow in the vicinity of the crusher during tipping, and a strong influence of the background ventilation regime on the path taken by this shear flow. Scale experimental studies were conducted to characterise the induced shear flow and visualise the potential entrainment and transport of dust. An analysis of these experiments is presented.

Jan 1, 2005

Stilfontein Gold Mine, located approximately 160 km west of Johannesburg, produced both gold and uranium from 1952 through to the early 1990s. On decommissioning the mine infrastructure, treatment plants, rock dumps and three tailings facilities were left to be rehabilitated at considerable cost to the mining company. The community that had grown up with the mine and had settled in the mine village were faced with deteriorating socio- economic conditions.   Mine Waste Solutions (MWS), a company with a socio-economic Vision expressly created by DRD (Pty) Ltd and Fraser Alexander (Ltd) for the purpose, took over the mine surface infrastructure with the objective of closing it down in an economically sustainable manner by recovering materials, converting mine infrastructure to useful purposes and re-mining of the tailings to recover residual gold to finance the project. A business case was prepared and presented successfully to investors and bankers and the project was commenced in 2003.   The paper covers the scope of the project and gives an account of the practical lessons that were learnt as the project developed over a period of five years. Key technical issues that are covered by the paper are the re-mining techniques that were deployed to clean up the old tailings dam footprints and the selection of the deposition site to minimise the incremental impact associated with the tailings and concurrent rehabilitation of the facility. In addition the paper will outline the positive benefits that were generated for the community and the improvement that was achieved in the physical environment.   The paper illustrates clearly how a mine can be closed in a manner that produces benefits for the community, the environment and the investor.

Jun 1, 2010

By S Nie, I Bergqvist, F Ouchterlony

In blasting, a few or many cracks are driven from the borehole into the rock. But what causes the cracks? The most common theory of breakage consists of two stages; first the shock wave causes radial cracks to form around the hole then the gases penetrate into the cracks, and widen them and make them longer. Another theory presented by Brinkmann suggests that the back damage is primarily controlled by shock and that the gas penetration is the mechanism controlling breakout of the burden. He did his experimental work using blasthole liners. Recent research at SveBeFo has examined this matter further. In a quarry a number of benching holes have been blasted simultaneously. In some of these holes tubular Swellex bolts were inflated and decoupled charges put inside the tubes without stemming. Other holes were identically charged but without the lining. Finally some holes were also stemmed. After blasting the cracks in the remaining rock were studied. There was no difference in crack lengths between holes charged normally (no stemming) and holes where the charges were inside the bolts. On the other hand when stemming was used, the crack lengths increased for some explosives but remained the same for an emulsion explosive. In another set up blasted granite blocks were charged in the same way as above. Then we could also measure the bore hole pressure. The pressure gauge consists of a small carbon resistor inside a steel cylinder. It is called LHM (Location-fixed Hydrodynamic Measuring Cup) and is placed at the bottom of the hole. A smaller exit hole from the bottom is drilled for the cables. The paper presents the technique and the results obtained from both the quarry blasting and the blasting of the blocks.

Jan 1, 2001

By J Plinke

The imperative to operate sustainably requires all equipment and processes to operate at their maximum possible efficiency. Achieving this ideal state requires a thorough understanding, not only of the process itself, but also of the tools available to design and assess potential improvements. This paper presents a case where the widely employed Discrete Element Method (DEM) toolset proved insufficient to model problematic material flow during the process of optimising wet screening performance. A Smoothed Particle Hydrodynamics (SPH) model was found to more accurately replicate the flow characteristics of the physical system. Site observations identified biased loading of the screen decks to cause inefficiencies in the wet screening of an iron ore processing circuit. Two numerical modelling approaches were pursued with the aim to select the most suitable one and continue the optimisation process based on that selected model. Selection criteria were established, based on the minimum requirements of being able to replicate the problem, including the main flow dynamics deemed to cause the issue. The DEM model was found to over-simplify the slurry flow dynamics within the scrubber and no laterally biased flow was introduced by the scrubber’s rotation to the otherwise symmetric system. Since DEM was not able to accurately replicate the existing problem, it was deemed an unsuitable method to assess the effect of any changes to the system. The second approach consisted of a SPH model. This model was deemed to map the flow within the scrubber with sufficient accuracy to address the problem, as it produced biased screen loading comparable to that reported from site. Changes to the wet chute, delivering material from the scrubber to the screen, aimed to neutralise the non-centrality introduced via the scrubber, were then successfully designed and assessed using the SPH model.

Nov 8, 2021

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By Guarascio M, Massacci P

In process simulation, more reliable prediction of industrial results and evaluation of data for design purposes and process optimisation may be attained by the combined use of: the modelling and simulation of ore characteristics, and 2. the modelling and simulation of the process. It is well known that geostatistical methods allow the defining of models of orebodies in which the variables considered are the grades of the valuable components. These models are proper for reserve estimation, geostatistical contouring, design and simulation of the exploitation method, and, in addition, for evaluating the variability of the ROM which is expected to be fed to the processing plant. However, no data are normally incorporated in the orebody model in order to evaluate the ore characteristics relevant for a reliable process simulation. The procedure for process simulation aimed at predicting plant results normally used so far consists in collecting samples from different orebody sites and building up a so-called 'representative sample'. On this sample, the ore characteristics (eg liberation, washability, grindability, etc) and the processing tests are referred to as the 'average behaviour in the orebody', assumed constant. A more reliable methodology consists in collecting samples from different orebody sites, in performing tests to characterise the samples from the point of view of the process (ore patterns), and in using synthetic parameters (process features). The values of the parameters are processed using geostatistical methods in order to develop a model for simulating the feed to the process. The estimation may thus be referred to the amount of recoverable minerals instead of to the existing minerals. Furthermore, the selection of the processes, the sizing of equipment and the design of control devices, as well as the prediction of results, become more accurate and reliable.

Jan 1, 1993

By D Lozada, A Salazar

Geometallurgy is a tool that, for more than a century, has been present in the implicit operations of mineral beneficiation. There’s a need to understand the characteristics of the material to be processed. This has led metallurgists to ask geologists what type of rock and mineralogy is entering the Beneficiation Plant and vice versa. The geologist needs to understand the beneficiation process in order to be able to carry out the production programming. The paradigm is whether geometallurgy can be applied to small-scale mining or if it is only aimed at large companies that invest millions of dollars to conduct studies. With this work, we provide an example of how geometallurgy can help improve the processes of a small mining company located in Ecuador (South America). We performed characterizations of geological and mineralogical and metallurgical tests in universities and the National Research Institute of Geological Metallurgical Mining. The origin of the theme is based on the fact that gold has been detected in the final tailings. The flotation concentrates meet the standards in terms of the content of economically profitable metals, but this isn’t the case with regards to the percentage of arsenic, which has hindered sales. The hypothesis is: conducting technical and scientific research will optimize the metallurgical process for the recovery of gold and concentrates. The referential framework is the mining geology of the Bella Rica District, current status of the Beneficiation Plant. In the theoretical framework there are parameters of the veins, comminution operations, gravimetric concentration, flotation, and cyanidation. The methodological framework contemplates the characterization of the gold ore, the chemical, mineralogical, textural, metallurgical analysis and the interpretation of the results. Thus, the design of a geometallurgy model of the deposit, with its main characteristics, is a conclusion that serves as a basis for the proposal of the optimization of the metallurgical process.CITATION:Lozada, D and Salazar, A, 2018. Geometallurgy applied to small-scale mining: a case study, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018