Search Documents

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

In the 1890s, The Goldfields Water Supply Department in Western Australia commissioned the diamond drilling of two deep artesian exploratory water bores near Coolgardie (Blatchford, 1899). At the time, in spite of strongly-worded advice to the contrary from the Government geologists, there was a wide popular belief that you could obtain artesian groundwater virtually anywhere providing you drilled deep enough. The first Coolgardie hole was drilled to over 900 m, despite the fact that the bore penetrated granite from a depth of 5 m below the surface. Drilling proceeded for more than 16 months, between July 1896 and November 1897. A small quantity of salt water was struck at a depth of 36 m. The second bore was mercifully terminated at a depth of 50 m, also in granite, with again only a small inflow of salt water. Such were the desperate lengths that were pursued to obtain a reliable water supply for the influx of people in the Eastern Goldfields gold rush. The WA Goldfields continued to rely on huge condensers for water supply until that great engineering feat, the construction of a water pipeline from Mundaring Weir to Coolgardie, was completed in 1903. An enormous network of rail tracks penetrated outwards from Kalgoorlie and Coolgardie for the collection of timber, principally to feed the condensers. Remnants of the rail network are still visible today. The acute shortage of fresh water led to great deprivation, disease and death among the early miners. Today, the water problems faced by the mining industry are thankfully not as severe, but they are nevertheless no less challenging. The southern part of the WA Goldfields is a notoriously difficult area for finding potable quality groundwater. Even as recently as the 1990s, there were occasional serious efforts to find potable groundwater in that area, some very imaginative and innovative. One mining company, working south of Southern Cross, spent many months experimenting with recovery of potable quality water from a shallow freshwater lens overlying hypersaline water in a low permeability weathered granite aquifer. They used very low capacity pumps manufactured from car windscreen washer pumps powered by solar panels.

Jan 1, 2000

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

Bendigo is AustraliaÆs second-most productive goldfield, having produced some 22 million ounces of gold between 1851 and 1954. Bendigo Mining Limited (BML), the sole lease-holder of the Bendigo Goldfield, is developing a mine that is planned to produce ore from beneath the historical workings for at least the next 25 years. The high-grade Bendigo reefs occur in the proximity of the chevron anticlines, which characterise the goldfield. Typically the reefs display relatively small cross-sectional areas and large (subhorizontal) strike dimensions. They occur in clusters due to interrelated structural controls. Most of the gold occurs as visible grains and laminae, and as such grade estimation is not amenable to ænormalÆ sampling and estimation techniques. The initial phases of exploration and development of the mine focused on understanding and resolving these sampling and estimation issues. In 2005, BML reviewed and updated the March 2004 Feasibility Study, refining the life of mine development strategy. The strategy fundamentally aims to exploit the 11 million ounce Inferred Resource and additional exploration potential by developing the current Kangaroo Flat Mine to produce ore at an initial rate of 450 000 t/yr in 2006/07, expanding to 600 000 t/yr by 2009/10; and developing the Eaglehawk Mine to produce 1 Mt/yr by 2011/12. Ore will be processed initially at the Kangaroo Flat site, and from 2011/12 also at the Eaglehawk Mine 1 Mt/yr processing plant. The two mines will connect underground in 2009. Total ore treatment capacity will be 1.6 Mt/yr, producing 600 000 oz/yr from a head grade of 12.7 g/t gold. The project is planned to operate for 25 years, processing 33.6 Mt of ore producing 13.7 Moz of gold. To achieve this production rate, the exploration and ore delineation programs will require up to 16 diamond drill rigs producing over 200 km of core per year. At the same time, approximately 8 km of on-reef development must be monitored and typically 18 stopes managed concurrently. The processing plants will be located in geographically constrained areas, which will limit the ability for selective stockpiling and campaign treatment.

Jan 1, 2006

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

By R N. Humphries, R J. K Thompson

Large-scale coal mining in South Wales dates back to the late 18th and early 19th centuries with the birth of ironmaking on an industrial scale. This rapidly gave rise to new and large communities with immigration from far and wide across the United Kingdom (UK). These new communities were largely dependent on coal mining and served as the main form of employment and social cohesion until the industry’s demise in the 1990s. With wholesale mine closure and the concomitant loss of employment, the extensive environmental degradation and chronic mine-related illness left a deep scar on the psyche on many still living in the South Wales mining communities. This coupled with memories of strife in the 1980s has resulted in ongoing hostility toward the surface coal mining of the remaining accessible coal reserves in the proximity of these communities.The purpose of this paper is to set out the historical basis of the concerns of these legacy mining communities in South Wales and explain how they are being positively addressed by both the recently evolved planning and regulation system and by today’s surface mining industry. Reference is made to experience gained from two recent applications for surface coal mining adjacent to former mining communities. Ways are suggested in the approval process that surface mining can work in more harmony with the local communities through working partnerships between the mining company, the authorities and regulators and the affected communities. It is concluded that partnership is key to creating a more responsive mine-operating culture and a means to securing approval for future surface coal-mining prospects in South Wales, and probably elsewhere too.CITATION:Humphries, R N and Thompson, R J K, 2014. Surface mining and legacy mining communities in South Wales, UK, in Proceedings Life-of-Mine 2014 , pp 399–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By E Niva

The IsaMillÖ is challenging the way that plants are designed and operated. This paper challenges existing designs of concentrator flow sheets, particularly focusing on magnetite circuits.   From what has started out as a small scale ultra fine grinding mill in the pharmaceutical and pigment industries, it has been redesigned and improved upon for mineral processing, and has been the mainstay of fine grinding applications for over ten years. These applications have required energy efficient grinding to succeed, and have been predominately in the base metals industry.   Further development of the IsaMillÖ has now resulted in the machines being able to treat larger tonnages, with higher capacity motors. This development, along with the introduction of purpose designed ceramic media, has allowed the mill to treat courser feed sizes. At the same time, the mill still offers highly efficient grinding, and has enabled it to be operated in coarser tertiary and secondary grinding applications.   The acceptance of the mill in coarser applications, predominately in base metals and PGM applications, has enabled the IsaMillÖ to be a serious contender for beneficiation in other minerals. One such application is the potential for IsaMillsÖ to be part of magnetite flow sheets, which are being considered in Australia to meet the growing iron demand of China. The high energy efficiency of the IsaMillÖ compared to conventional technologies, as well as the smaller infrastructure requirements, provides a great opportunity to reduce the power intensity of magnetite circuits.   This paper will examine the use of IsaMillÖ technology in conventional grinding applications, including recent testwork in a primary grinding base metal circuit, as well as testwork on magnetite ore comparing a lab scale IsaMillÖ with a lab scale Tower Mill.   The growing demand for minerals over the next decade, coupled with higher energy cost, will result in energy efficient technology, such as the IsaMillÖ, being included in standard circuit design.

Jan 1, 2008

By Grady B. V O, Cavell K. J, Ault A. R, Newman O. M G, Malcolm J. McPhersqn

Cyclic voltammetry (CV) has been evaluated as a technique for monitoring the quality of an industrial zinc sulphate electrolyte. The basis of the method involves measuring a change in the polarisation of the zinc nucleation reaction at an aluminium surface and relating this to the impurity content and/or the overall quality of the electrolyte. Specifically, the technique aims to be able to indicate and quantify detrimental synergism between impurity elements, something which traditional analytical techniques are incapable of providing. The technique has found some success with regard to monitoring glue additions in a range of metal electrolytes. It has been found that investigations by a number of workers over the past 15 years have produced variable and often misleading results due to the inadvertent use of commercial purity aluminium working electrodes. It has been shown that impurity elements in the working electrode can give rise to a range of responses that are not obtained when pure aluminium is used and that the response is variable due to the lack of surface homogeneity of commercial purity aluminium electrodes. Furthermore, it was demonstrated that previous detection limits reported in the literature were based on the presence of additional peaks in the cathodic scan and not polarisation effects. The results of this study have shown that when a pure aluminium working electrode was used, the method was incapable of detecting any change in polarisation for an electrolyte containing three common impurities (Co, Ni and Ge), at concentrations that would significantly reduce optimum electrolytic performance. A range of methods was tried to sensitise the technique, including raising the temperature and acidity, and adding antimony in order to induce some synergism. In all cases the polarisation response was unchanged. Consequently, apart from the commercialised application for monitoring additions of antimony and levelling agents such as glue, CV has very limited application as an electrolyte screening technique.

Jan 1, 1993

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

By M Lynch, B White

The historic city of Charters Towers in North Queensland is underlain by an extensive labyrinth of old mine workings in a large number of flat lying, subparallel, main and cross-cutting cross reefs extending of the order of 5 km along strike and down to a depth of 700 m in parts. These old workings produced over 6.6 million ounces of gold at a grade of over one ounce to the tonne prior to closure in 1920.Citigold is progressing the development of a modern, high productivity, low cost new mine to extract extensions of these reefs as well as other as yet un-mined reefs. To do this it is changing the paradigm for operating in such circumstances. This paper first briefly reviews the setting for the development and then discusses the philosophies and concepts that Citigold is proposing to use, harnessing technology to create a mine that exemplifies more productive and safer mining based on operating in the digital age.The paper addresses how a modern approach is being applied to the planning of a mechanised, deep, narrow vein, hard rock gold mine under a city. It also describes briefly the successful æexperimentationÆ with longhole open stoping methods developed at the companyÆs small underground operation (the Imperial Mine) to the south of the city, which will also be expanded substantially as part of the Charters Towers Gold Project.The paper also addresses the development of new and/or modified technologies in the venture, with the objective of pursuing continuous and autonomous mining methods. The company is adopting a holistic systems approach, addressing people, process and technology in order to efficiently identify and locate the high-grade ore zones and then extract them effectively at a high grade by minimising waste development and haulage, dilution and energy consumption, and with minimal environmental impact.CITATION:Lynch, M and White, B, 2013. Brave new world autonomous mining systems, in Proceedings World Gold 2013 , pp 157-166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J Samosir, L A. Snyman

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.An issue affecting production in 2011 was the stability of the E48 mine. A small portion of the drives on the extraction level began to deteriorate as the ground support system failed. The problem was temporarily fixed by stopping production in three extraction drives and tight filling selected areas within these drives (and drawpoints) with low-strength concrete. This action provided immediate support and stability whilst allowing time to investigate potential ground support remedies. From these investigations it was decided to use resin injection technology and additional ground support to stabilise the rock in the aforementioned extraction drives as the concrete plug was excavated in a controlled advance and sequence. This made the area safe and ensured the ongoing safe operation of the E48 mine. The redevelopment of one of these drives began late in 2011, with the remainder being progressively redeveloped over the next two years in order to maintain the extraction level stability.This paper looks at the strategies employed to safely re-open previously converged drawpoints and associated extraction drives that were subject to high abutment loading that was possibly associated with premature cave breakthrough.CITATION:Samosir, J and Snyman, L A, 2014. Redevelopment at Northparkes following significant drive closure, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By ZáWang, F Hungerford, T Ren

Operations in an underground drill site have to co-exist within the mineÆs ventilation and operational system. The space requirements of a drilling operation have to be adapted to the limitations provided in available site space, which is usually defined by standard mining operations and geotechnical influences. These limitations affect borehole design, equipment positioning in the site layout and possible interactions with mining equipment and services such as water and power supply.The ventilation requirements for drill sites and the means employed vary with depth of the site, space and likely presence of gas. All drilling operations provide a particular service for the mine and in each case, drilling must operate in a manner which controls all gas, water and cuttings returning from the borehole. The various standpiping systems employed have evolved under differing influences and must cater for conditions during and after the drilling operations.The influences that gas content, pressure and flow, rib stability, cleat direction, borehole length, potential water pressure and flow have on a mineÆs operation and ventilation systems have to be considered in the design of standpipe length, diameter and fittings. Past history has a strong influence on common practice while worst case effects of a possible in-hole event should be catered for.This paper describes the early drilling systems and their limitations in ventilation and gas management. The drill site dimensions and set-up are discussed in the context of roadway conditions, equipment layout, ventilation and logistics. The use of standpiping to control all returns from the borehole is illustrated by referring to likely scenarios in a drilling site to achieve the most effective sealed depth to accommodate the worst case possibility of intersecting high pressure gas or water during the drilling operation. Practices to allow gas drainage in the return airway of a panel are described.CITATION:Hungerford, F, Ren, T and Wang, Z, 2013. operational management of underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference , pp 43-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Jankovic, D David, P Payne

Although the majority of current steel production is supported by iron ore sourced from high-grade haematite deposits, the long-term growing demand for steel has led to higher raw material prices and opened the way for many new magnetite deposits to also be developed. There is a rich and long history of magnetite ore processing in Western countries, including large operations such as Cleveland Cliffs in the USA and LKAB in Sweden, as well as smaller operations like Savage River in Tasmania. The challenge for virtually all magnetite operations is to minimise operating costs, which is dominated by the cost of power required to fine grind the ore in order to achieve acceptable concentrate iron grade together with low impurity content. This remains the case today and will be even more important in the future when a carbon tax is expected to become a significant addition to the operating costs for magnetite deposits. Historically, the lowest operating cost was achieved by multistage fully autogenous grinding with integrated magnetic separation steps between the stages. The major benefit of fully autogenous grinding is the elimination of steel grinding media costs and the need to discriminate between steel and magnetite in coarse magnetic separation. The separation step between grinding stages progressively reduces the amount of material to be ground. Application of more efficient grinding technologies developed in the last 20 years, including high pressure grinding rolls (HPGR) for fine crushing and stirred milling for fine grinding, has provided opportunities to further reduce the operating costs associated with comminution. Both technologies are already implemented in some magnetite processing operations, although in limited capacity. The results of a theoretical option study for high capacity processing of a hard, fine-grained silica-rich magnetite ore is presented in this paper, with the emphasis on comminution circuit options. Several circuit options are ranked based on a net present value analysis incorporating an estimate of carbon tax added in the operating cost. The study demonstrates the significant advantages of applying more efficient autogenous grinding technologies.

Jan 1, 2009

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Computation is believed to be a powerful tool in scaling-up chemical processes and in designing materials, however, is being challenged by low predictability and limited scalability. This presentation will discuss the promising future of multi-scale computation in solving these two problems to realise the real-time simulation of industrial processes. Multi-scale structures are a common nature of most chemical systems and the meso-scale phenomena are believed to be the road blocks not only in improving the predictability of physical modeling but also in extending the scalability of computation. Focusing on the meso-scale phenomena, a series of research has been carried out at the Institute of Process Engineering, Chinese Academy of Sciences, for the past three decades. Starting with a simple idea of modeling the meso-scale clusters in gas-solid two phase flows, the so-called EMMS (Energy-Minimisation Multi-Scale) model was established. In verifying the stability condition of the model, the pseudo-particle approach was proposed to explore the micro-mechanisms in particle-fluid systems, and the strategy of the EMMS model was extended to other six different multi-phase systems, resulting in a unified conceptual formulation of multi-phase complex systems expressed by a multi-objective variational problem. In applying this model to different multi-phase systems and to industrial problems, it was recognised that the EMMS model defined a new paradigm of multi-scale computation by realising the structural similarity between software, hardware and the problems to be computed. This paradigm of computation was implemented on a multi-scale supercomputer with a capacity of 1.0 petaflops by integrating CPUs and GPUs (Graphic Processing Units), showing high efficiency and low cost. Running the EMMS model on this computer, the simulation of hydrodynamics of multi-phase systems can be speeded up very much, indicating a promising future of virtual reality of process engineering. The presentation will review this series of work, introduce successful applications in industries, and will be concluded by emphasising the critical importance of the meso-scale phenomena as the bridge between macro-dominants and micro-mechanisms. This is an ABSTRACT ONLY. No full paper was prepared for this presentation.

Sep 13, 2010

By A Bouazza, J Kodikara

In this study, 23 samples of leached ash (LA) were collected from an ash pond at Loy Yang Power Station and geotechnically characterised. The samples were collected at various depths and locations within the ash pond on two separate occasions in order to account for the full variability. The LA within the ash pond at Loy Yang Power Station (LYPS) was found to vary in texture from silt to sand, depending on the location from where the sample was collected. Samples collected near the ash pond inlet discharge point, for instance, contained more than 50 per cent sand sized particles and were subsequently classified under the Unified Soil Classification System (USCS) as silty sand (SM). Further downstream of the inlet discharge, the LA became progressively finer and was classified accordingly as elastic silt (MH) when the sand content became less than 50 per cent. Basic geotechnical testing revealed that the LA from Loy Yang Power Station was generally acceptable as a landfill cover material. The permeability of LA, however, was generally too high for prescriptive covers, (ie resistive covers that generally rely on the impervious nature of the material to control percolation). Alternative covers, generally rely on the store/release function of a capillary or monolithic barrier to prevent percolation into the landfill. Subsequently, a material that can maintain a high water storage capacity while at the same time, readily allow infiltration and evapotranspiration is required for an alternative cover. Sandy silt and silty sand are optimal soils for alternative covers, as they do not yield water to gravity forces, but do give up most of the water in their pores when subjected to high-matric suction (Kavazanjian, 2001). The effectiveness of alternative covers is ultimately assessed using computer models, such as UNSAT-H and HYDRUS-2D, to rigorously perform water balance calculations. Prior to using a computer model to determine the highest possible percolation in the worst climatic conditions, it is necessary to select the most appropriate materials. This paper suggests a method to screen available materials for use as an alternative cover material on the basis of the soil water characteristic curve (SWCC).

Jan 1, 2003

By S La Brooy, C Fountain

Throughout its history the mining industry has focused on the highest-grade deposits sited in the most convenient locations. The burgeoning global population and higher standards of living not only increase the demand for mineral products but also make it harder to mine and process them. The future will include the development of lower-grade, more complex orebodies, and orebodies in difficult locations. The industry will be expected to provide for humanityÆs needs while reducing its environmental footprint and maintaining profitability. This paper reviews some of the likely adaptations in mineral processing that will occur over the next 20 years. The challenges inherent in adapting to lower grade and more complex materials might be exacerbated by such factors as the availability of water and low-cost energy. In underground mining, higher energy costs are likely to foster further developments in underground preconcentration, especially for ores that can be upgraded at relatively coarse sizes. The adoption of underground crushing could also render material amenable to semi-dry preconcentration options such as might be achieved by the rotary classifier developed by CSIRO and being commercialised by RCR Tomlinson, or more modern versions of the hand-sorting of ore that use sensors based on colour or other suitable rock properties. The cement industry and some gold roasters have used the alternative of dry grinding and classification, which might also have a part to play in dry processing. There is also likely to be increased interest in options such as in situ leaching that further minimise the surface disturbance. Underground operations will have to balance the energy savings from reducing the amount of material brought to the surface and reduced surface disturbance against the practical limitations of installing and maintaining processing equipment underground. On the other hand, surface disturbance and energy issues in open cut operations will be balanced by potentially lower mining costs and higher overall recovery from the deposit.

Jan 1, 2008

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003