Search Documents

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By D Capstick, M B. Ebell

This paper describes the test work, process design, commissioning and operation of a processing system at the Ergo gold operation that improves the extraction efficiency from gold tailings material. The improvement in recovery is derived from the separation of the gold contained within the sulfides of the tailings material and a dedicated process stream to recover that gold.The sulfides are separated by means of a flotation circuit and that resulting concentrate is subjected to a regrind of below 20 ¦m to enable a greater liberation of the gold. The ultra-fine material is then subjected to a dedicated leach circuit to recover the now exposed gold particles.The case study is an example of the challenges of introducing new technology and methodologies to a well-established operation and thereby attaining improved efficiencies and tangible business benefits.CITATION:Ebell, M B and Capstick, D, 2013. Improving extraction efficiency from Witwatersrand gold tailings using flotation and ultra-fine grinding of concentrates, in Proceedings World Gold 2013 , pp 301-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By H Han, d S. Hapugoda, L Lu

With the recent rapid development of Chinese steel industry, the world iron ore resources of good quality are depleting rapidly. As a result, iron ore deposits of lower quality have been or are being developed to meet the market demand and are becoming increasingly important to iron and steel companies. As concentrates have advantages of high Fe grade and less harmful impurities, they are ideal sweeteners to maintain sinter grade and quality when high proportions of low-grade ores are used in the sinter blends. However, due to their fine nature, addition of concentrates will inevitably increase the proportion of adhering fines and reduced the proportion of nucleus particles of the sinter blends, which can adversely affect the green bed permeability and sintering productivity. In the present study, lab scale sintering tests were carried out under the conditions similar to the sintering process to examine the effect of concentrates on the high temperature sintering characteristics of sinter blends and the structure and strength of the resultant sinter analogues.

Sep 18, 2023

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By P Trotta

The paper provides a structured methodology to investigate metallurgical problems within the operating concentrators. The strategy uses classical metallurgical data analysis as well as pulp, solution and surface analysis to determine the reasons for particular behaviours. The approach applies equally to all mineral-processing operations. To demonstrate its effectiveness a case study, based on work conducted at Pasminco Rosebery Mine, is described. In this work, the classical metallurgical analysis indicated that a significant amount of sphalerite reporting to the lead concentrate occurred as liberated particles. A combination of pulp, solution and surface analysis supported the hypothesis that the liberated sphalerite was recovered by inadvertent activation by lead ions. Laboratory studies have indicated that the use of sodium carbonate, by itself and in combination with zinc sulphate and sodium cyanide, when added to the lead regrinding mill can depress sphalerite flotation, resulting in an improvement in the lead grade/recovery curve. When this approach was tested in the plant other more dominant issues masked any positive effect the addition of sodium carbonate may have had. The plant trial highlighted the real need for additional regrinding capacity.

Jan 1, 2002

The classic description of Project Finance as "the reliance by lenders on the cashflow of a project, supported by the assets of the project with no recourse to the project sponsor's corporate balance sheet" has, like most other terms in the finance industry, evolved through recent usage. The area now under most scrutiny is the sharing of risks between parties either most able to take them or prepared to accept payment for them. Creativity in, and flexibility of financing structures have enabled project lending to continue under a dramatically different economic outlook. The diminishing competitiveness of the Australian producers in a global market place of uncertain commodity prices has discouraged the advancement of many large scale resource projects. The majority of new project financings has been designed to assist the relatively small company promote and develop its first projects. New trends- are emerging in four areas: sources of capital; borrowing structure; financing instruments (securitisation); and risk underpinning. As project financing becomes more widely used, the range of interested financiers grows. New initiatives contribute to its development and evolution with a view to increase effectiveness to the sponsor of any new venture.

Jan 1, 1987

By K Schiefelbein, P OÆGrady, R Balusu, T Ren, T Harvey

"An extensive research program has been undertaken over recent years to reduce the risk of fires and explosions in underground coal mines. The research projects have integrated extensive field studies and computational fluid dynamics (CFD) models of goaf gas flow behaviour to develop optimum proactive strategies to prevent and control spontaneous combustion and fires ingoaf areas. The research has developed a fundamental understanding of the air and gas flowbehaviour in goaf areas and provided a detailed understanding of the eff ects of various geological,ventilation, operational and inertisation design parameters on goaf gas distribution. The researchinvestigations have also provided a better understanding of the flow behaviour of gases from the heating in the goaf areas and the effect of various gas and spontaneous combustion controltechnologies and strategies. Field studies conducted at a number of underground coal mines have shown that the proactive strategies were successful in reducing oxygen ingress into the goaf areas and in reducing the risk of fires and explosions in the underground coal mines. The results of various research investigations and guidelines for reducing the risk of fires and explosions in underground coal mines are presented in this paper."

Jun 1, 2012

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

By Smith J. W, Wilkins R. W T

This paper is a preliminary report of research on the Mount Morgan gold-copper deposit being done at the Division of Mineralogy, CSIRO. Fluid inclusion and sulphur isotope measurements were made on a suite of 11 samples collected by the staff of Geopeko Ltd. This suite contained representatives of the main ore and rock types of the deposit. Homogenization temperatures of fluid inclusions measured on quartz from 8 of the 11 samples, ranged from 172¦C to 276¦C and to this must be added a pressure correction (in this case, up to 50¦C) to obtain the formation temperature of the mineral. Sulphur isotope measurements were made on 34 sulphides from 8 of the 11 samples. The 6S values form a well defined group ranging from -0.5%oto +3.6%owith a mean of +2.4%c. Although the preliminary data do not indicate unequivocally the origin of the deposit they do impose restraints on the wide ranging suggestions that have been put forward. This work is complementary to the paper of Dr G. Gibbons who has described other mineralogical aspects of the Mount Morgan deposit, based on a more extensive suite of Samples.

Jan 1, 1974

By Toop G. W, Martin M. T

At the Cominco Ltd plant in Trail, British Columbia, the Betts lead electrorefining operation requires that antimony and arsenic be present in the lead bullion for anode slimes stability control. Until 1986 the antimony and arsenic inputs from concentrates to the Lead Smelter needed to be supplemented with high antimony and arsenic content recycles from the Silver Refinery operation to maintain a satisfactory composition. Subsequently the antimony and arsenic inputs have increased as a result of increasing levels of antimony in Sullivan lead concentrate and the purchase of larger quantities of silver/gold bearing concentrates that inherently have higher antimony and arsenic levels. The increase has exceeded the limits required by the Betts process. It therefore became necessary to install a partial softening process downstream of the Continuous Drossing Furnace to satisfactorily control the bullion composition. Process control and oxygen injection techniques used in the partial softening process are reviewed. Approximately 8 tonnes/day of softening slag are produced having a combined antimony and arsenic content of 25 percent. This slag is reduced in a recently commissioned short rotary furnace followed by vacuum distillation of the metal for recovery of the antimony and arsenic values.

Jan 1, 1989

The cost of production from truck and loader fleets is influenced by management development of the culture of the organisation, work practices, systems and procedures of the production and maintenance teams. Establishing if the cost of production is the best that can be achieved then requires the measurement of results against established standards of performance. This paper provides a series of discussion points of the factors that influence the cost of production from men and machines for large scale open pit mining operation and provides some suggested performance standards in the form of Benchmarks. Most of the references have been drawn from established large scale deep pit mines in USA, Canada and Australia which have had to implement and constantly fine tune cost efficiencies in order to survive. The discussion provides:ò a review of priorities or the relative importance of the various cost elements for a mining system;ò suggestions of systems and procedures for the operation and maintenance of machines which are considered to yield the best overall results;ò examples of operations that have developed and implemented management systems and controls that are achieving good results in specific functions; andò suggested benchmarks of performance.

Jan 1, 1992

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

An improved method of sample recovery for use with rotary percussion drilling has been developed. Cuttings can be recovered continuously from either dry or wet drilling, and the recovery under dry conditions is seldom below 99% of the cuttings brought to the surface by the rig. The system is designed for use with top drive drilling rigs using flush-jointed drill rods. The key feature of the system is a self-aligning mechanical seal around the drill rods. The sealing unit is removably fixed to a collar section of cas ing. the cuttings are recovered in a plastic bag attached to the bottom outlet of a cyclone. A valve at the bottom of the cyclone permits the cuttings representing various depths to I,e recovered separately for examination eind 0(iclysis. [u the Iron Monarch quarry, two percussion holes were drilled to depths if 30 metres and 28 metres using the unproved sample recovery system, and diamond drill holes bored 1 metre from each percussion hole. Samples from each hole were sectionalized over metre intervals and analysed for iron, silica, alumina and loss on

Jan 1, 1976

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

By J A. Meadows, M G. Annandale, G Castelain

Bauxite mining on Cape York Peninsula (CYP) commenced in the early 1960s in the region surrounding the town of Weipa. Rio Tinto Alcan (RTA) operates its bauxite mines on the homelands of 11 Indigenous Traditional Owner groups. The mining activity currently operates under three Aboriginal Agreements including an Indigenous Land Use Agreement – the Western Cape Communities Coexistence Agreement (WCCCA) – which provides RTA with access to the land in return for a range of benefits to the Traditional Owners, including employment, training, royalty payments and future relinquishment of the land (Klimenko and Evans, 2009). Despite reports of some ‘good progress’ in meeting the terms of the WCCCA (Klimenko and Evans, 2009, p 5), many of the region’s Traditional Owners remain dissatisfied. Two key areas of Indigenous community concern are the current premining management practices and the outcomes of post-mining landscape rehabilitation efforts.CITATION:Annandale, M G, Castelain, G and Meadows, J A, 2016. Sustainable mining – indigenous community benefit, in Proceedings Life-of-Mine 2016 Conference, pp 173–175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomogr`aphic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First- arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

Today the application of computer programs for planning of mine-ventilation and for safety- analysis of ventilation systems is widespread practice in German mining. The computer program for network calculat- ion, developed at the "Mine Ventilation Testing Centre of the Westfalische Berggewerkschaft- skasse" allows the distribution of airflow and pressure in mines to be calculated. In a physically well founded manner it takes into account the natural ventilation as well as changes of volume-flow in the mine, which both are dependent on pressure and temperature. Compared to an incompressible treatment of the mine air these circumstances are of increasing importance with the increase of depth, air temperatures and fan-pressures'. This especial- ly holds for the calculation of airflows during failures of fans or for assessing the influence of open mine-fires on ventilation. The application of the program is very easy and its structure is made to fit the requirements of practice. For instance it takes into account the fan characteristics of all fans. For each planning calculated air- flows in all mine workings are compared to those of an eligible basic calculation or to measured airflows. In addition for the

Jan 1, 1983