Search Documents

Gold occurs at Mt. Charlotte associated with a stockwork of pyritised quartz veins in Unit 8 of the Golden Mile Dolerite. The ore- body is massive, 200m long and 40m wide and has been proved to over 600m below surface. Mining is by sublevel ring drill stoping with the ore recovered by diesel powered equipment. Ore reserves are based on traverses of diamond drill holes oriented to produce an equal intersection width on the two principal sets of quartz veins. Assay and geological boundaries are marked on each drill section and this boundary is transferred to mine plans and cross sections. Ring-drilling patterns are based on the cross sections and the resulting mining outline is transferred back to the drilling sections. The mine ore reserve is calculated from the mining outline.

Jan 1, 1979

By Chend J

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled scopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench scope fill mass is described and a technique for reducing the potential for bulkhead failures in hench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also descrihed.

Jan 1, 1998

By Mitchell D. S

BackgroundIn March 1990 Pasminco resolved to replace and increase the capacity of the underground pumping system at the Southern Operations, Broken Hill. The existing pump station was built 23 years ago while the rising main had been in service for 38 years and was subject to frequent failure.The old system was a conventional slurry/clear water separation and multi-stage pumping system. It was inadequate in the following areas:ò insufficient capacity to handle current and expected future flows;ò unable to consistently dewater lower production areas; ò pumping capacity restricted sandfilling rates;ò dirty water dams had insufficient settling capacity and were difficult to de-sludge;ò the operating costs of dewatering were high; ò it was labour intensive; andò it did not offer enough protection to the 25 level loading station.

Jan 1, 1993

By Brown N. R

This paper attempts to highlight some of the problems encountered in the economic exploitation of the deeper coal seams by opencast mining methods. The major cost elements of three methods of overburden removal are examined in relation to the overall cost of winning coal from deeper-lying coal seams. The three overburden removal methods examined are dragline stripping and two systems combining dragline stripping with shovels and trucks at varying depths of overburden. A dragline is, undoubtedly, the most cost effective system of overburden removal for depths of up to 30 metres but it is suggested that, when dealing with incremental overburden depths in excess of 30 metres, engineers should consider carefully the possibility of using a shovel and truck operation, or other system, to augment the use of a dragline.

Jan 1, 1986

By Weber P, Sneyd S

The total world steel production in 1998 amounted to approximately 780 000 000 t. The share of electric steelmaking was in the range of 35 per cent and is expected to increase further to over 40 per cent of the world's production within the next ten years. As electric steelmaking is primarily based on the use of scrap and as it is progressing more and more into higher steel grades the need for low-residual metallics will become increasingly important. Consequently, the demand for scrap substitute material will increase, reflected in the world wide spate of interest for DRI (Direct Reduced Iron) and HBI (Hot Briquetted Iron). The increased significance of DRI/HBI as a substitute for steel scrap has obviously emanated also from its comparatively lower and more predictable costs per ton and definable chemistry. In 1998 already 37 million tons of DRI/HBI were globally produced.

Jan 1, 1999

Geochemical data on Australian granites and pegmatites, and the mineral components of these rocks, are compared with that obtained in similar studies in the U.S.S.R. and elsewhere.The geochemical character of tin granites and the trace chemistry of their component minerals, particularly biotites, have some significance as ore guides in prospecting for tin.The primary geochemical dispersion of tin can be readily tested both in the laboratory and field by colourimetric methods, after volatilization with ammonium iodide, using modifications of the method described by Wood (1958).Secondary dispersions of tin in residual soils or alluvia can likewise be readly tested by rapid colourimetric methods in the field, but simple hydraulic methods, handling larger sample volumes, give reliable outlines of dispersion patterns.INTRODUCTIONThe search for tin ores, whether lode or placer in type, is usually directed on genetic grounds to country within or adjoining acid intrusives.A long established means of prospecting is to test samples for cassiterite by panning or other hydraulic separation.These methods can be used on crushed lode material or the natural materials from placers.With the advent of new techniques for extraction and for colourimetric analysis for tin (Wood, 1958 and Ross and White, 1961) a means is available for rapid analysis of materials not susceptible to quantitative testing by hydraulic methods because of the fine sizings of cassiterite or the occurrence of tin structurally held in minerals. The new methods thus opened up the field of tin prospecting by extending the search for ore guides to genetically associated rocks and minerals, wall ror-ks of veins and a wider range of superficial deposits.

Jan 1, 1963

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

Enhancement of Energy Efficiency in Fine Grinding of Copper Sulfide Minerals Using a Pilot-Scale Stirred Media Mill - IsaMill The mineral liberation size of run of mine ores has dramatically reduced over recent years. As a result, the demand for fine grinding which is the most energy-intensive form of grinding has markedly increased in the minerals industry. Furthermore, the fine grinding costs increase exponentially with decreasing product particle size. As a result of the increased energy requirement for fine grinding, it is desirable to optimise fine grinding processes such as stirred media milling (ie IsaMill) to enhance energy efficiency, throughput and the product fineness. In the present study, the influence of slurry rheology, grinding media type and grinding media-to-feed size ratio on energy efficiency in a pilot-scale IsaMill was investigated under certain industrially relevant pulp processing conditions. It was shown that a critical rheological state existed, below which the energy required to achieve an 80 per cent passing (ie P80) 20 ¦m product size was unaffected by shear rheology (ie apparent viscosity and shear yield stress) whilst above which the grinding energy required increased dramatically with increasing shear rheology. Colorado River sand (3.35 mm) showed higher energy efficiency than MT1 ceramic media (2.5 mm) for a target P80 of 20 ¦m in the solids concentration range of 38 to 55 per cent by weight, but the former experienced more than four times the wear rate of the later. The high wear rate of the Colorado River sand may be due to its much lower hardness. For feeds with an 80 per cent passing (ie F80) 70 to 110 ¦m, 2.0 or 2.5 mm MT1 media appeared to be more energy efficient than 3.5 mm MT1 media whilst a media-to-feed size ratio of 41 to 53 is applicable for ~50 ¦m (ie F80) feeds for efficient grinding.

Sep 13, 2010

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a 'possibility, and that it was unlikely that a small bore...

Jan 1, 1950

By Griffin P

The project is the result of a European Commission supported collaboration between Surpac Software International, the Technical University of Berlin, and the industrial partners Exploration and Bergbau GmbH (E+B) and Taylor Woodrow. The object

Jan 1, 1998

By Hongzhen Yu, Xiaoping Ma, Jiansheng Qian

The paper introduces the design of an Intelligent Managerial Attendance Machine (IMAM) for coal mines. In the system, data communication is carried by Optical fiber communication, including industrial control computer on the ground and the car

Jan 1, 1998

By Bhattacharyya A. K

A strata parameter is introduced to include the deformation characteristics of the undermined strata in the prediction of subsidence movement. By using the strata parameter and mining factors as parameters, a nomogram for predicting the maximu

Jan 1, 1994

Classification within the Inferred Resource category is based on geological judgement and the balance of extrapolation versus interpolation that the Competent Person is prepared to accept. These resources are typically drilled at spacings well in excess of the geostatistical range and at a density that is non-uniform. In many cases, a substantial proportion of the available data will be historical, and should be considered with more recent data sources. The provision of a robust geological model will increase the confidence in any resource estimate, and should be viewed as a critical component. The definition of Inferred Resources is of great importance to vein gold projects, since Indicated and Measured Resources generally require costly underground development for delineation. Indeed, many gold vein operations possess substantial quantities of Inferred Resources (>75 per cent) in their resource inventory both at project start-up and during production. This contribution explores a number of the key issues when using the Inferred Resource category and presents four recent case studies.

Jan 1, 2006

By B Upton, J Mitchell

The use of hydro scaling and in-cycle shotcrete to replace conventional jumbo scaling, mesh and bolting as the primary method of ground control for run of mine development has been investigated through extensive trials at the Waroonga mine, Agnew Gold Mining Company.These trials have progressed from investigating the productivity aspects of the method through to a three month mine-wide trial, which may yet lead to the adoption of this potentially best practice ground control technique at Agnew.Ov erseas trials and research have shown that hydro scaling results in a significant improvement in the shotcrete-rock bond strength. Good adhesive bond strength ensures that the shear strength of the shotcrete layer rather than itÆs flexural or tensile strength is fully mobilised as rock mass reinforcement.This maximises shotcretes ground reinforcement capability and it is suggested that a bolt-less fibrecrete support design is feasible using the hydro scaling technique.

Jan 1, 2005

By S Dorrington, J Olsen, N Kinkaid

Several studies have been conducted on the economic analysis of mining near-Earth asteroids for resources for use in Earth orbit. While these studies use detailed economic figures of merit, they often use many invalid assumptions in the trajectory design. Factors such as the energy and propellant requirements are estimated with analytic methods, however, the stay-time at the asteroid and the spacing of repeated launch opportunities are not taken into account. The work outlined in this paper attempts to combine detailed trajectory design methods with newly defined economic figures of merit to improve the economic assessment of asteroid mining missions. The study focuses on asteroid 2014 EK24, a near-Earth asteroid with very Earth-similar orbital properties.CITATION:Dorrington, S, Kinkaid, N and Olsen, J, 2015. Trajectory design and economic analysis of asteroid mining missions to asteroid 2014 EK24, in Proceedings Third International Future Mining Conference, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Armony, J F. C L Costa, J C. Koppe

Linear kriging methods fail to estimate local grades and local reserves for highly skewed variables due to three reasons: it uses only part of the available data information, it has no physical principles associated with the mathematical proceedings to minimise the problems, and it works with continuous variables while data are discrete because of the limited precision of any equipment. The techniques commonly used up to now to solve the highly skewed variables estimation problems were unsuccessful, unless mathematical rigor is abandoned. Even the method of multiple indicator kriging is not satisfactory. This paper presents a new framework, the field parametric geostatistics (FPG) that transforms noisy variograms into well-behaved variograms and justifies mathematically empirical procedures commonly used, as trimming or capping arbitrarily very high values. The method, when applied to non-skewed variables, yields similar results to classic kriging. The methodology is illustrated in a case study at a gold deposit in Brazil, and compared to results obtained by usual techniques.

Sep 26, 2011

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

By G J. Lyman

Sampling of grain for mycotoxins is challenging in that some mycotoxins, such as Ochratoxin A (OTA), have very low permitted levels and the kernels carrying the mycotoxin may be highly localised within the bulk of the grain as ‘hot spots’. Sampling for genetically modified organisms (GMOs) can be fraught with similar problems, especially if the contamination is adventitious and random. Incremental sampling under these circumstances can be shown to lead to a high variance in the sampling result.A new design of sampler for grain and other free-flowing particulates has been developed that is effective in practically eliminating the sampling variance due to distributional heterogeneity (DH).This paper introduces the design and argues that the sampler should be free of sampling variance due to DH.CITATION:Lyman, G J, 2017. A new sampler for grain and other free-flowing particulates, in Proceedings Eighth World Conference on Sampling and Blending , pp 277–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017