Search Documents

By M A. Wells

The various mechanisms by which phosphorus (P) occurs and is distributed within banded iron formations (BIF)-derived iron ore are examined. In unenriched, precursor BIF P occurs predominantly as discrete grains of primary apatite. In high-grade ores hosted mainly by the Brockman Iron Formation, P occurs in three main forms:1. as secondary apatite;2. other submicron, P-rich phases (eg Rare earth containing minerals (REE), vivianite, strengite,wavellite) present in pore networks; and3. as P occurring with iron oxides, in particular, goethite.However, the presence of secondary P-bearing phases does not contribute signifi cantly to the total P level in iron ore, and it is P associated mainly with goethite, which represents the most common occurrence of P in these ores.No direct evidence for the replacement of Fe by P within the structure of synthetic goethite has been demonstrated. Therefore, it is most likely that in iron ores P associates with goethite in occluded form as adsorbed PO4 3- species or as discrete P-bearing minerals, such as strengite, wavellite or vivianite, in ultra-fine, micro-pores or within intra-domain regions of multi-domainic goethite. Such occluded P is not easily extracted with commonly used lixiviants, such as weakly alkaline leachates. Recent development of a low temperature-alkalie/water leach extraction method has been successful in reducing not only the P content, but also amounts of Si and Al inthe initial ore. Refi nement of such a method to commercial application will have enormous benefit in realising the economic potential of large tonnages of high-P (ie >0.07 wt per cent P) bearing iron ore.

Jul 11, 2011

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022

By F Burns, G Peachey

The Hidden Valley process plant has recently undertaken a program to relieve process flow bottlenecks and improve process automation. An environment of cost reduction and restrained capital necessitated solutions that primarily utilised existing equipment and internal resources. Removing bottlenecks relieved pressure from a strained circuit that was unable to maintain consistent performance. Improved process automation firstly stabilised the process, then allowed the circuit to sustainably operate at the expanded capacity limits. These allowed implementation of an operating approach that focused process operators towards identifying and resolving process disturbances in advance. Plant recovery and throughput have markedly improved as a result.CITATION:Burns, F and Peachey, G, 2014. Recent process improvements at Hidden Valley gold mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 43–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Gigmai W

Ok Tedi Mine is a high production open pit porphyry copper mine located high in the Star mountains of Papua New Guinea. The mine produces an average of 160 000 tonnes of ore and waste daily at a 1:1 strip ratio. Full scale drilling and blasting began in 1988, prior to which time all material was ripped and dozed.Drilling and blasting procedures at Ok Tedi underwent a major review commencing mid-1989. As a result of a mutual commitment by management at Ok Tedi and the mines explosives supplier ICI, significant reductions in overall blasting costs have been realised. These cost savings are primarily the result of the introduction of air bags, expanded patterns and better field execution.

Jan 1, 1992

By M I. Pownceby, S Hapugoda, H Han, E Donskoi, L Lu

Iron ore sinter mineralogy and its associated macro-/micro – structure has a strong impact on sinter quality. At a macroscopic scale, sinter ideally consists of a strong, porous matrix which bonds relict ore nuclei together. Microscopically, the sinter matrix (solidified from the melt part of the initial sinter mix) generally consists of complex calcium ferrites known as SFCA, secondary magnetite and hematite grains (precipitated from the primary sinter melt), glass and silicates. Depending on the conditions under which the sinter structure is formed, two major forms of SFCA with different morphologies are generally recognised, ie fine micro-platy SFCA (usually termed SFCA-I) and coarse columnar/prismatic SFCA. Detailed optical microscope observations of several pot grate and compact sinter samples revealed the presence of a variety of fine, coarse and dense forms of both types of SFCA. The controlled cooling tests revealed that cooling rate has an impact on the form and size of SFCA crystals. In this work, EPMA analysis of SFCA compositions from a variety of pot grate and compact sinter samples are presented. Results show that the SFCA types exhibit a broad range of complex compositions within the system Fe2O3/CaO/SiO2/Al2O3/MgO/TiO2/MnO2. Although SFCA-I and SFCA are known to be crystallographically distinct and with different, well-defined ranges in composition, there was considerable overlap in compositions of the experimental sinter samples. The development of SFCA textures depend on several parameters including the local chemistry and conditions including the maximum temperature attained and the cooling rate, within the sinter bed, thereby suggesting that SFCA identification based on morphology alone may be erroneous.

Nov 8, 2021

By D E. Thorp

The mining and concentration operations of New Zealand Steel have been carried out initially from the Waikato North Head (WNH) deposit since 1969 and subsequently from the Taharoa deposit since 1972. Over the years the WNH operation has produced about 1.2 million tonnes of concentrate which has been converted into steel, while total exports to the Japanese Steel Industry from Taharoa reached five million tonnes in February of this year. Recent expansion plans both in domestic steel production and in the ironsand concentrate export market have made it necessary for the company to look closely at, among other areas, the mineral processing of the titaniferous ironsands in both deposits. This paper deals with the recent test work carried out at WNH and Taharoa on the use of the cone concentrator unit as a primary gravity concentrating unit ahead of the magnetic separation stages and as a cleaner concentrator following the primary magnetic separation.

Jan 1, 1977

By E Gabriel, J C. Koppe, A Gomes and P Crispim, R Schaarsdmit, I Pablos

Drill and blast (D&B) is one of the most important production operations in open pit mining. The resulting fragmentation of the D&B reflects in the downstream unit operation. Good fragmentation of the ore will minimise the cost of loading, hauling and crushing. The understanding of the geological model integrated with a software system for bench face surveying and planning of blast layouts based on three-dimensional images can help to achieve the fragmentation goals of the mine operation. A case study integrating these tools was carried out in a large iron mine in Brazil. The iron ore in the study area consists of hard and friable itabirites. More than three different ore types may occur on the same bench. Under these conditions, data integration becomes necessary to improve the results of blasting. A blasting plan was based on the generated geological model. The methodology helps understanding the factors that can interfere in the fragmentation process, allowing defining actions that can improve the blast design in those places that fragmentation wasn’t achieved. This condition is important for a continuous improvement of the drilling and blasting operation. In comparison with the previous blasting carried out at Itabira mine, which did not take into account the geological model, substantial improvements in fragmentation were observed, eliminating the need for secondary blasting.CITATION:Schaarsdmit, R, Pablos, I, Koppe, J C, Gabriel, E, Gomes, A and Crispim, P, 2015. Geological modelling and bench face survey to improve blasting fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 401–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Barritt

Remedial options for a waste rock dump (WRD) were considered as part of closure planning studies at an active mine in Western Australia. To minimise the impact of any seepage from the landform it was determined that placement cover system utilising the moisture ‘store-and-release’ concept was appropriate. The purpose of the cover system was to:•Reduce net infiltration of meteoric water to attenuate peak concentrations for contaminants of concern in natural receptors to levels that can be assimilated without adverse impact to the surrounding ecosystem; •Provide a growth medium for establishment of a sustainable vegetation canopy; and •Improve current quality of surface water runoff from waste storage areas.The project comprised several phases of work: materials characterisation, numerical soil-plant-atmosphere (SPA) modelling and finally cover system construction and monitoring equipment installation.CITATION:Barritt, R, 2018. Conclusions from long-term cover system performance monitoring – a case study, in Proceedings Life-of-Mine 2018, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J J. Eksteen

"In the platinum group metals (PGM) industry, smelters are often perceived as ‘black boxes’ that have to process concentrates of variable mineralogy and originating from multiple mines operating along strike or downdip from each other in the same geographical region, as is the case in the Western Bushveld of South Africa. However, PGM smelter complexes are much more sensitive to concentrate blend variation than most metallurgists or geologists would anticipate.This paper will review the impact of concentrate blends deriving from a number of concentrators processing ores from the Bushveld Igneous Complex (BIC) on smelting and converting behaviour and the constraints they impose upon smelter operation. Significant variation in behaviour is not only noted between the main mineralisation types, namely the Merensky and Upper Group 2 (UG2) reefs, but also within a given reef type. Due to the way PGMs are mineralised and finely disseminated, concentrators have to grind concentrates ultra-fine to liberate the PGMs and provide a sufficiently high-grade concentrate for smelting.The chemistry and mineralogy of the concentrates vary with the type of mine (open pit versus underground), the reef type and varies along strike; this variation impacts numerous key smelter parameters such as the base metals content, the matte fall, the converter aisle capacity, sulfur dioxide gas production, furnace matte and slag temperatures, and the accumulation of high smelting chromite-spinel minerals that has led to significant smelter upset conditions such as catastrophic furnace hearth and sidewall failures.Due to the production intensity of smelting, ie its high rate of processing per unit volume, smelters have been found to be far more sensitive to rapid variation in concentrate properties, highlighting the need for adequate blend control.CITATION:Eksteen, J J, 2016. Impact of Mineralogical Variation on the Smelting of Cu-Ni-PGM Concentrates, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By G D. McDonald

Flinders Mines is an ASX300 iron ore explorer and developer with a tenement package located in the Hamersley Ranges region of Western Australia, approximately 70 km north of Tom Price. Exploration over the past three years has identified a Global Resource in excess of 740 Mt at a grade of 55.4 per cent Fe (+50 per cent Fe cut-off). This resource is spread across multiple deposits and has been divided into a number of mineralisation type domains based on geometallurgical and geochemical boundaries. These domains are comprised of transported haematite rich detrital iron deposits (DID) and goethite dominant Channel iron deposits (CID) as well as in situ bedded Brockman iron deposits (BID). On the basis of differences in physical and chemical characteristics, the DID have been divided into four discrete units. The four DID units form a stratigraphic sequence with the iron grade increasing and the contaminant concentrations decreasing with depth. The upper DID unit is lower grade and currently unlikely to provide a marketable product, without signifi cant beneficiation. The lower three DID units, together with the CID and BID, are of a higher quality and have the potential to yield marketable ore. The ability to define and recognise these different units has resulted in a more reliable and robust geological interpretation and hence greater confidence in the resulting resource model. This has been evident in the excellent conversion of inferred to indicated resources.

Jul 11, 2011

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

By C M. MacRae

The characterisation of high-P iron ores by field emission gun electron probe microanalyser (FEGEPMA) was carried out to determine elemental associations in iron oxides sensus lato and, using this knowledge, to speculate on possible P incorporation mechanisms in goethite. Quantitative data was collected from two goethite-rich bulk ores and results showed that in both samples goethite was the main repository for phosphorus. The P-rich goethite also contained elevated levels of both aluminium and silicon.To understand the mechanism of P incorporation in goethite, high-P grains were located by coarse mapping of polished blocks with the FEG-EPMA. Analysis of element distribution maps collected on the P-rich grains showed that low-P regions within grains were typically associated with low-Al and high-Si, whereas high-P regions were associated with high-Al and low-Si. Based on follow-up quantitative analyses, a coupled substitution mechanism for phosphorus incorporation within goethite was proposed: 2Si4+ = 1P5+ + 1Al3+. Additional quantitative analyses on further examples indicated the mechanism was only valid for Si contents in goethite of <1 wt per cent.Preliminary transmission electron microscope (TEM) studies confirmed the presence of P, Al and Si in goethite.

Jul 11, 2011

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By S Amor, A Beasley

This paper provides an example of how industry can respond to the implementation of new regulatory approaches to mining risk, health and safety by adopting a robust, practical, software-based approach to the management of risk accountabilities in terms of competence, experience and suitability for obligations and responsibilities, as required in Queensland Coal Mining operations due to the introduction of Recognised Standard 22 (‘RS22’; Resources Safety and Health Queensland, 2021). Based on the authors’ experience from working with several Qld mine operations, it offers a snapshot of the experiences, approaches and reservations faced collectively by industry as a result of the introduction of RS22. Several challenges exist within the detail of RS22, leading to varied interpretations, implementation strategies and overall compliance between mine sites. Arguably the single biggest challenge identified has been how to find a balance between compliance and practicality – considering cost, operational interruption, available pathways for delivery of competence, ongoing compliance and value adding to the business operations and people. Software-based solutions are increasingly being relied upon to address the introduction of new regulatory approaches and the significant administrative load placed on mining operation Site Senior Executives (‘SSE’) due to RS22 means this case is no different. This is further complicated given the continuous, ongoing changes with the site management structure witnessed by the authors across each of the mining operations as a result of continuous changes to personnel, the site risk profile and an overall mining industry uncertainty of how to respond to RS22. The stringent reporting/notification requirements under legislation compounds this further. The approach put forward by the authors is a well-considered rationale and approach to the application of training and skilling; and equally how to ‘future proof’ the coordination of site training needs around changes to the Management Structure, the Risk Register, skilling processes and succession planning. A brief investigation of other legislative frameworks concluded this approach would likely meet or exceed expectations of jurisdictions across Australia and overseas, making this a highly flexible approach for establishing a competent Management Structure to provide safe systems of work.

Apr 16, 2024

By A Gray

Physical separation features in almost every mineral processing circuit. The category encompasses a broad range of techniques and technologies including hydrocyclones, gravity concentration methods (including jigs, spirals, centrifugal concentrators, tables, heavy media separators) and thickeners, all of which make use of the inherent density differences between two mediums. It is also possible to include flotation, magnetic separation, and ore sorting in the physical separation category.However, opportunities for enhanced physical separation performance can now go beyond the common practice of optimising unit operations. Improved options exist for feed preparation ahead of the physical separation stage, enabling higher performance and lower cost outcomes for physical separation flow sheets and technologies.The use of new applications in breakage technologies combined with mineral liberation analysis to optimise liberation prior to the physical separation stage provides options for preconcentration and gangue rejection as well as better separation efficiency. The use of low cost gangue rejection and preconcentration can be an intermediate step between mining and processing that allows processing of lower cut-off grades from the mine whilst delivering higher grades to the mill.Optimising flow sheets and technology performance requires detailed understanding of particle size and shape distributions as well as liberation characteristics to suit the particular separation unit, combined with knowledge of the available technologies, their capabilities and the economic impact across the whole mine cycle.CITATION:Gray, A, 2017. The role of liberation in physical separation techniques, in Proceedings MetPlant 2017, pp 147–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By I R. Souza

At the mining industry, there are several uncertainties that may affect the mobile mining equipment fleet sizing and usage, such as commodity supply and demand, which impacts the mineral price, environmental licenses to allow operations and strategic decisions made by the own mining company. Due to that, it may happen to acquire a mobile mining equipment for a specific site and before it finishes the entire forecasted life cycle, the machine gets idle on that operation and a decision must be made regarding this matter. On large mining companies with several sites, equipment transfer provides a good solution to solve this issue and at the same time it provides operational flexibility and allows to use the equipment until the initially planned working hours. This article presents a method to compare technically and financially whether it’s more feasible to transfer a used equipment or to buy a new one. In other words, we will compare a brand-new machine versus a used one in terms of safety, net present value (NPV) considering both capital expenditures (CAPEX) and operational expenditures (OPEX), technological obsolescence, risks, equipment maintenance reliability and lead times. Although it’s not the main purpose of the paper, it will also be briefly discussed the importance of having a considerable amount of backup equipment to handle low likelihood and high consequence risks that may materialise. This backup equipment portfolio is particularly important to avoid loss of sales and profits in case the production plan changes and it demands further equipment than initially planned to cope with the forecasted production.

Nov 8, 2021