Search Documents

Traditionally, surface coal mines in the Western United States have been limited by economics to depths between 150 to 200 feet. Utah International Inc., however, is now planning to strip coal its San Juan Mine in Northwestern New Mexico to depths ranging up to 400 feet while uncovering 20 feet of steam coal. This method is cost-competitive with nearby shallower coal deposits and underground mining of the same property. How trucks and shovels can pre-strip for a dragline, along with results of the planning process, comparison with alternate systems, capital requirements, operating costs and comparisons with other coal sources are all detailed. Also discussed are the major problems anticipated, how they might be corrected, and potential improvements to the concept. Introduction The San Juan Deep Stripping Project will be situated at Utah International's San Jean Mine. The mine is in the Four Corners region, so-called because four states enjoy a common border point about 30 miles to the northwest.(see Figure 1). The area is a semi-arid plateau region with an average elevation of 5,200 feet, receiving an average of 6 inches of precipitation annually

Jan 1, 1981

By S Hapugoda, A Edenton, L Lu

The blast furnace cohesive zone has a profound impact on hot metal productivity and quality, fuel consumption, operational stability and the lining life of the blast furnace. The high temperature properties of ferrous burden materials determine the configuration and location of the cohesive zone and have therefore attracted particular attention. While numerous standard testing methods are in use to assess the quality of ferrous burden materials for the blast furnace, these simple tests are generally conducted under fixed conditions, which often represent the extreme situations encountered by the burden materials in the blast furnace. Furthermore, none of these simple tests provides information on the high temperature properties of the burden materials, such as their softening and melting properties. CSIRO is equipped with a fully computerised testing facility to characterise the high temperature properties of ferrous burden materials under realistic conditions similar to those encountered in the blast furnace. This paper will first review the CSIRO softening and melting test method and then discuss the softening and melting properties of a variety of blast furnace burden materials, including sinter, pellets and lump ore, and their implications for blast furnace operation.

Nov 8, 2021

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By C J. Moran

All mines face water management challenges. Adopting leading practice water management strategies can help reduce both operational and strategic risks. While many of the water issues faced by underground mines are the same as other operations, underground mining presents some unique water management challenges. In this paper we review trends in underground mining, water use and associated water issues. We then compile a structured set of strategic and operational risks that are pertinent to underground operations. The causes, threats, opportunities and measures for controlling or mitigating the risks are summarised. The risk compilation could provide an addendum for underground operations to the Australian governments leading practice water management handbook.

Mar 21, 2011

By R D. Morri, D J. Alexander

The design and optimisation of mineral flotation circuits is currently performed using a combination of laboratory, pilot plant and full scale testing. Owing to the variable nature of flotation circuits and the complex nature of the flotation process, it is difficult to interpret the data collected from flotation testwork. JKSimFloat is a computer modelling package which is being developed to interpret flotation testwork data collected at the various stages of the mining cycle. The parameters derived from the program can be used to assess potential circuit configurations in both the design of new flotation circuits and in the refinement of existing operations. The aim of this paper is to outline the modelling methodology used in JKSimFloat and to outline how it can be used effectively to model data collected from either the laboratory, the pilot plant or the existing flotation circuit. The use of flotation model parameters in circuit evaluation will be demonstrated via the use of a case study based on data collected from ComincoÆs Red Dog lead flotation circuit.

Jan 1, 1998

In the general planning of this area, provision was made for the distribution over the whole area as required of the following services:(a) Power and lighting from the substation distribution boards 'located in the winder house.(b) Miscellaneous electrical indicating, control and signalling systems.(c) Telephone lines from the main internal automatic exchange located in the changehouse, the town exchange to the automatic exchange and also direct lines from the town exchange to selected offices.(d) Compressed air from the incoming 16-in. air main. (e) Water, both unfiltered and filtered; and the disposal of the following effluents:(f) Sewage from the area to the town sewage system.(g) Changehouse shower water to the regeneration area.(h) Storm water to the general mine surface drainage system leading out to the naturally drained area north of the No. 8 Shaft.

Jan 1, 1957

By B Levasseur, C Olsen, E Ghasemian Langeroudi, F Larachi, F Safizadeh, C Gagnon

Gold recovery by the cyanidation process is often accompanied by the leaching of other species. This leads to the depletion of the level of free cyanide and oxygen available for gold cyanidation. The largest proportion of the consumed cyanide is diverted by the cyanicides (eg S, Cu, Zn, Fe, etc) into non-valuable complexes.COREMÆs Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during preoxidation and cyanidation. Flotation tailings and single mineral samples such as pyrite, sphalerite and chalcopyrite, along with their different combinations, were analysed to highlight the influence of ore mineralogy on the operating conditions. The effects of different kinds of oxidants (oxygen, hydrogen peroxide, ferricyanide and ozone) and chemical additives (ammonium sulfate) were investigated.Experiments conducted in alkaline solutions reveal that mineralogy is a key parameter since pyrite, chalcopyrite and sphalerite react quite differently during preoxidation and cyanidation. A significant increase in sulfur dissolution, especially on pyrite, was observed by applying preoxidation. H2O2 preoxidation showed a positive effect on increasing sulfate formation, a desirable by-product from the cyanide consumption point of view. Preoxidation of synthetic ores with ferricyanide resulted in boosting thiosulfate formation. Tests conducted on flotation tailings from a polymetallic mine revealed that a short preoxidation increases the dissolution of the ore leading to higher gold recovery and lower cyanide consumption. Regarding the formation of thiocyanate, the most undesirable by-product of the cyanidation, ferricyanide and ozone were found particularly efficient to hinder their formation. Finally, the addition of ammonium sulfate during the cyanidation process showed some promising results in terms of both gold dissolution and cyanide consumption.CITATION:Ghasemian Langeroudi, E, Levasseur, B, Safizadeh, F, Olsen, C, Larachi, F and Gagnon, C, 2013. Optimisation of operating parameters for cyanidation of sulfide-bearing gold flotation tailings in order to prevent the impact of cyanicides, in Proceedings World Gold 2013 , pp 111-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

In a previous paper the author showed that silver considerably delayed the recrystallisation of lead after cold work. The effect of antimony on the rate of recrystallisation of distorted lead was studied next, and the experiments performed, and the results obtained, are described in this paper. Electrolytic lead was used as a standard of comparison.It was also used to make the lead antimony alloys.This electrolytic lead contained 0.0005% total impurities.It was prepared from commercial lead by fire refining, followed by electrolysis and finally by vacuum casting. The process was described in the previous paper and the description need not be repeated here. PREPARATION OF LEAD - ANTIMONY ALLOYS.The steps taken to procure pure antimony are outlined in the appendix. To make the lead antimony alloys a mother alloy was prepared thus:-A quantity of the antimony (it was received in the powdered form) was placed in a pyrex glass tube, which was closed at one end. The antimony was washed with hot hydrochloric acid (1: 1), then with more dilute acid, then with distilled water, and finally with absolute alcohol; it was dried by warming and evacu,ating the tube. This should leave the antimony more nearly free from surface oxides.The amount of antimony was determined by weighing quickly; the appropriate amount of vacuum-cast electrolytic *Research Fellow, Dept. of Metallurgy, University of Melbourne.

Jan 1, 1936

By D Smith

The Broken Hill deposit is located in Australia in the far western region of New South Wales. The deposit was found in 1883 and has been mined continuously since its discovery. It is considered the largest lead, zinc, silver deposit that has been discovered in the world and originally contained around 340 Mt of ore at a grade of around 12 per cent lead, ten per cent zinc and 150 g/t silver. The material remaining in the deposit represents only a fraction (perhaps ten per cent) of the original resource. Several of the world’s largest mining companies can trace their origins to the Broken Hill Field. The remaining resources on the CML7 consist of two large lower grade resource lodes that have not been subject to mining, some scattered areas of zinc lode material and the pillars and remnants of the main lead lodes.The deposit occurs in metamorphic rocks of the Broken Hill Group a division of the Willyama Super Group contained within the Curnamona Craton. The Broken Hill Group rocks have undergone multiple phases of deformation. Metamorphism is granulite grade with major shears cutting through the deposit having been retrogressed to mica schists. The deposit lies in an antiform associated with the second phase of deformation.The resultant proposed mine is situated on Consolidated Mining Lease 7 (CML 7) which occupies a strike length of 3.6 km in the central part of the 7.8 km long footprint of the orebody. Underground mining on CML7 ceased in 1975 with surface mining of silver chlorides in the weathered zone continuing until 1991. CBH Resources has been continually working to define and evaluate the remaining resource since 2002. This work has included four surface drilling programs, two underground drilling programs, an exploration decline, enormous amounts of compilation of historical data and detailed three- dimensional (3D) modelling of historical mining and the resource lodes. It is currently planned to commence production at the Rasp Mine in late 2011. The operations will produce from previously unmined lodes and from remnants and pillars.This paper primarily aims to encapsulate the processes involved from information acquisition through to resource estimation and also to highlight some of the challenges encountered and the specific techniques and practices used to overcome them. Many of the experiences at Broken Hill are applicable to all brown field sites.

Aug 22, 2011

By M Breen

In 2009, George Fisher mine began to seriously consider the transition from pyrotechnic detonators to electronic detonators. Initially, the electronic detonators were used for complex crown shots or areas where ground conditions had the potential for excessive overbreak. After critically evaluating the potential safety benefits, production increases and ability to redesign stopes to better manage a thinly bedded hanging wall, the mine decided to embrace the technology.

Nov 8, 2011

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By C Zhang, R Liang, I Canbulat, S Saydam, B Li

The integration of digital twins in mining represents a significant advancement towards enhancing operational efficiency and decision-making. Central to this development is the role of visualisation, a crucial element in mining digitalisation. This paper aims to develop a data-driven visualisation solution for the construction of mining digital twins, highlighting how this innovation revolutionises the representation of physical mining environments. It spotlights the shortcomings of conventional visualisation methods, particularly their inability to accurately depict complex underground environments and their predominantly historical orientation. To address these challenges, this paper proposes a novel, data-driven approach. This approach extensively utilises CAD files, encompassing data from geological surveys to intricate mine plans, thereby significantly elevating the precision of digital twins. It supports real-time updates and enables flexible interaction with a variety of data types. Moreover, it introduces a comprehensive data diagram alongside the adaptation of a 3D tile index. This strategy ensures the efficient rendering of extensive mining environments, allowing for a more dynamic and interactive digital twin model. In conclusion, the implementation of data-driven visualisation in the construction of mining digital twins marks a pivotal advancement in the industry’s digital transformation. It promises a more detailed, accurate, and dynamic depiction of mining operations.

Sep 1, 2024

By Zichenko ZA, Volkov SV, Shaluhina LM, Emelyanov AF

A method of selective gold recovery from black sands has been elaborated which is based on the liquid phase low temperature chlorination of materials. A liquid agent mixture of sulphur monochloride S2C12 and sulphur dichloride SC12 is used. This method ensures the gold extraction either in the state of AuC13.SC14 complex salt solution or as metal. The kinetics and main physico-chemical parameters of the process (eg density, solid: liquid ratio, temperature) have been investigated. The materials investigated were quartz-insipid ride samples with low sulphur and high iron (up to 70 per cent Fe2O3) contents. Gold recovery is 96 - 99 per cent at temperatures not exceeding 100¦C. Most of the associated minerals remain in the cake. To obtain metallic gold, the resulting solution of the AuC13.SC14 salt after leaching is reduced by hydrazine with subsequent annealing. The elaborated method is remarkable for small energy expenditures owing to low process temperature and a high gold dissolution rate. The solution of sulphur chlorides and other reagents are used in closed cycle.

Jan 1, 1993

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By C Wels

Current best management practice requires the placement of a cover onto most types of mine waste including tailings, waste rock and/or spent heap leach rock at closure of the mine. The objectives of a cover system may vary from site to site but generally include dust and erosion control; chemical stabilisation of acid-forming mine waste (through control of oxygen ingress) contaminant release control (through control of infiltration); and/or provision of a growth medium for establishment of sustainable vegetation. In our experience, there has been a general tendency by stakeholders to develop performance criteria for cover systems, which are tied directly to these specific design objectives. In many cases, this practice has led to the development of single, often very conservative, numerical values of cover performance criteria such as ænet percolationÆ, ærate of oxygen ingressÆ and/or æplant density/mixtureÆ. In our opinion, there is a need to develop cover performance criteria on a case-by-case basis and with due consideration of the short-term and long-term impacts on the receiving environment at a particular site. This paper puts forward a methodology for developing site-specific performance criteria for a cover system designed to isolate acid-forming mine waste and to control acid rock drainage. The proposed methodology links the predicted performance of a cover system to groundwater and surface water impacts. This way, the appropriate level of control (of oxygen ingress and/or net percolation) required by the cover system can be determined. A case study is presented that illustrates the application of the methodology proposed in this paper.

Jan 1, 2003

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Robinson

Modem occupational health practice can be described as the fitting of work to the individual and each individual to his job; perhaps a non-traditional way to view occupational health. This two-component description is achieved through the development of programs to implement and monitor specific job procedures, from the monitoring of unwanted exposures to contaminants to the auditing of mine sites. This paper is about such programs. Some attempt must be made to evaluate the effectiveness of the program and several performance indicators which are intended to measure the effectiveness of such a program are offered.

Jan 1, 1994

By G Cao, Y R. Cui, J X. Zhao, H P. Gui, G H. Wang, Z M. Wang, M M. Ren, B Li

Pyro-metallurgy is still the main process for lead production and a lot of lead direct smelting processes have been developed in recent years. All the processes will experience two steps in common. The first is the oxidisation of PbS to PbO and then reduction from PbO to Pb, furthermore, from ZnO to Zn. So, the composition of melts, especially the slag composition at reduction step change continuously. Up to now, there are few systematic results on the slag physical-chemical properties with its composition change. In this work, the typical lead direct smelting processes were analysed from theoretical and practical standpoints. The full-period slag composition and slag melting point change were compared. Especially, to the PbO and ZnO reduction steps, based on the full-period slag composition change, the slag properties were predicted. Based on dust composition and test results, the mechanism of Pb compound evaporation and its effect on practice and measurement of high PbO bearing slag physical-chemical property is discussed. It is suggested that to restrain the evaporation in practice and to obtain more accurate measurement results of physicochemical properties of smelting slag are the key problem not only to set high efficiency, energy saving process, but also to environmental pollution control.

Aug 21, 2024

In the early 1950's, it was forecast that there would be, worldwide, a need for approximately sixty computers! Included in that estimate was provision for a considerable amount of geoscience modelling. Since 1950, the role and concept of the computer has changed. With that change has come alteration and adaptation within industry in order to better utilise the services and tools that computers can provide. For example the science of statistics prior to the computer was regarded as an intractible speciality. Computers have allowed the exploitation and further generation of statistical theory. In turn, as the science of statistics has become practical and relevant, the mineral geologist has moved from being essentially "a-numeric" to "non-numeric" to highly skilled in the application and use of very sophisticated statistical concepts. The modern computer provides the opportunity to perform many of the old practices more conveniently and/or economically and, perhaps more importantly, for exploration it provides- an enormous range of activities which previously would have been impossible. Such new activities allow for imaginative and creative application and extension of basic theory into practical situations, which when used by well trained, able people can open up new avenues of exploration. However, the use of such tools by poorly trained or incompetent people can lead to errors potentially as great as any success derived from the same tools. This paper reviews some applications of the computer to exploration, and attempts to discuss likely future developments.

Jan 1, 1987