Search Documents

By J Player, R de Vries, E Villaescusa, H Saw, R Hassell

The use of cemented rock fill (CRF) for support of open stope walls has increased in the Australian underground mines operations over the last five years due in part to its low capital cost. In open stoping the exposed CRF masses require adequate strength and stiffness, in order to resist the forces and to limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or from development mining waste sometimes up to 1 m in diameter. However, the use of waste rock, which has a poorly graded particle size distribution may not achieve the required minimum target strength due to segregation and large air voids within the fill mass. This paper describes the optimisation of CRF strength by either crushing the waste rock or the addition of sand to the mix. Both methods increase the level of fines in the mix design. Cylindrical samples having 400 mm diameter and 800 mm heights were prepared for uniaxial compressive strength (UCS) testing. The UCS test was determined using the Western Australian School of Mines (WASM) large-scale static test frame. The laboratory results were compared with a database of large-scale CRF strength mixed without sand from a number of mine sites around Australia. The comparison shows a significant strength development in the CRF mixing with addition of sand for a given cement percentage. Due to the higher strengths achieved by the addition of sand and the crushing of the waste material these CRF types require less cement to achieve the same strength. This has the potential to improve the overall economics of open stope mining due to less dilution of the exposed fill mass.CITATION:Saw, H, de Vries, R, Player, J, Hassell, R and Villaescusa, E, 2017. Optimisation of cemented rock fill strength for open stope support, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Z Zhao

Coal dust is hazardous to underground coal workers and water spray is the most common and economic method for controlling coal dust. Previous studies proved that the addition of surfactants can improve the performance of water spray on coal dust suppression. The evaluation methods for surfactants vary from different studies. The zeta potential test is a common method for evaluating surfactants with ionicity. Generally, the suspension of coal dust with pure water usually showed a negative value of zeta potential. The addition of cationic surfactants can increase the zeta potential to a positive value with a small dosage, while the addition of anionic surfactants can only lower the zeta potential. However, there is a lack of comprehensive study to investigate the relationship between the zeta potential and the suppression performance for coal dust. The aim of this study is to reveal the consistency and discrepancy between the zeta potential and the suppression efficiency of a surfactant. Firstly, the mixture of cationic surfactant solutions and coal dust would be evaluated by the zeta potential test. The wind tunnel tests would then be conducted for the same surfactant solutions to measure and calculate the suppression efficiency. It was found that the addition of surfactant can increase the zeta potential and the suppression efficiency and it reached the greatest efficiency when the zeta potential approached to zero. The equilibrium of zeta potential can benefit the suppression performance of surfactants in the wind tunnel test. The result of this study can achieve a better understanding of the mechanism for coal dust suppression. The selection of surfactants will also be suggested for researchers or industries in terms of coal dust control. It would be more economic if a similar performance could be achieved by less consumption of surfactants.

Oct 12, 2022

By I Lipton

The existence of metalliferous mineral deposits on the deep-sea floor has been known since manganese nodules were discovered in the Arctic Kara Sea in 1868. Modern exploration to define commercially viable base and precious metal deposits began in the 1970s and gained further momentum in the last decade. High grade deposits have been delineated but investors remain cautious, many considering deep sea mining projects to be riskier than terrestrial projects. This paper compares opportunities and risks presented by terrestrial mining projects with those presented by deep sea mineral deposits (Table 1). The Solwara 1 volcanic-hosted massive Cu-Au-Ag sulphide deposit, the Atlantis II Deeps sedimentary base metal sulphide deposit, and the Mn-Ni-Cu-Co nodule deposits of the north-eastern Pacific Ocean are used as examples. These are advanced deep-sea projects with published Mineral Resource estimates, on the cusp of development. Off-shore diamond mines in Namibia are also considered. These examples provide a basis for comparing exploration and geological uncertainty, the technical risks of proposed mining systems, and the potential environmental and social impacts. CITATION: Lipton, I, 2018. A comparison of opportunity and risk in deep-sea and terrestrial mining projects, in Proceedings Complex Orebodies Conference 2018, pp 102–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

The paper examines the difficulties encountered by objectors to mining privilege applications. It describes the various involvements of the environmental defence society in the mining controversy and makes some comment on the proposed amendments to the Mining Act 1971.

Jan 1, 1981

This brief overview of the history of Brown Coal mining in Victoria is a luncheon presentation -I do not intend to make it indigestible with extensive listings of resources or production. There is a vast pantry of collated historical records and of vari- ous predictive studies available for the enquired with a hearty digestion. A gourmet collation is provided in The Aus IMM Monograph No 11 published in 1984 entitled "Victoria's Brown Coal-A HUGE FORTUNE IN CHANCERY", currently still on offer by the Institute and available at a bargain price in the foyer at this conference. Monograph No 11 also provides a feast of excellent references on the theme of Victorian Brown Coal assembled by the several contributors. In contrast, my presentation paper is a fast-food service, extracts from the printed paper only-you have no choice-you "get what you get" and in small quantity. I hope it will tantalise your appetite -like Oliver Twist you will ask for more. -Buy the Monograph!

Jan 1, 1989

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method's capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. Since 1980, Australia's share of the world's output of these minerals has fallen. Exhaustion of known resources, together with the changing composition of new deposits, is expected to result in Australia's share of the rutile and zircon output continuing to decline. Its role as a major supplier of upgraded ilmenite, that is synthetic rutile, is expected to increase. In 1994, the Bureau of Resource Sciences assessed Australia's demonstrated resources of mineral sands as follows: rutile 14.4 Mt, ilmenite 132.5 Mt, and zircon 21.0 Mt. These resources are located along the coast of Queensland and New South Wales, in the Murray Basin of New South Wales and Victoria, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth. However, some 45 per cent of rutile and zircon resources along the coast of Queensland and New South Wales are not available for mining because of environmental concerns. World demonstrated resources are estimated at 40 Mt (contained TiO2) for rutile, 50 Mt for zircon and approximately 312 Mt (contained T1O2) for ilmenite. Outside of Australia, the most important resources of rutile, ilmenite and zircon are in South Africa (rutile, zircon , and ilmenite in the form of titania slag), Sierra Leone (rutile), India (ilmenite, zircon and rutile), and Canada (hard rock ilmenite). Significant resources of ilmenite occur in Madagascar and Mozambique.

Jan 1, 1996

By S Gossmann, J Barlow, S Denner

"Unconventional gas resources, including coal seam gas (CSG) reservoirs, can be located above and below aquifers that provide groundwater for agricultural, industrial, urban and other uses. Development of these resources may, therefore, lead to potential impacts on groundwater supply.Management of reservoir/aquifer interconnections necessitates a program of focused data acquisition. For example, groundwater transfer from shallow aquifers to underlying CSG reservoirs may occur where CSG-containing units subcrop beneath shallow aquifers, possibly at significant distances from operating wells.Arrow Energy is undertaking studies of connectivity between aquifers including an investigation in collaboration with the Queensland Office of Groundwater Impact Assessment to evaluate connectivity between the Condamine Alluvium (CA) and CSG-containing Walloon Coal Measures (WCM).The Condamine Valley hosts highly productive agricultural land with groundwater resources heavily utilised for irrigation. Water demand outstrips available supply and groundwater has been subject to restrictions on further development since the early 1970s. Developments that could have an additional impact on groundwater resources in the CA are of major concern to local landholders. This paper describes: planned field investigations at two sites: 1. Stratheden, where pumping from the WCM will be undertaken 2. Daleglade, where pumping from the CA will occur how the data to be collected from field investigations will be used to refine predictions of flux between the CA and the WCM.CITATION:Denner, S, Gossmann, S and Barlow, J, 2013. Planned field investigation of connectivity between the Condamine Alluvium and Walloon Coal Measures, in Proceedings Water in Mining 2013, pp 91-98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

Rheological Behaviour of Clay-Rich Gangue Mineral Dispersions During Hydrometallurgical Treatment Alumino-silicate minerals invariable may present an intractable challenge in hydrometallurgical operations employed in low grade nickel, copper and gold ore leaching or high level nuclear waste (HLNW) processing. The interactions and reactivity of alumino-silicate clay gangue minerals such as muscovite/sericite, chlorite, kaolinite and smectite under acidic (eg pH <3) or alkaline (pH >13) conditions can have a striking impact on the particle interactions. These may manifest in undesirable pulp rheology, poor extraction rates and challenges in the subsequent "handleability" and solid-liquid separation processes (eg dewatering). In the present work, a review of investigations involving the interfacial chemistry, interactions and rheological behaviour of aqueous dispersions of mica-group, layered alumino-silicate clay (muscovite / sericite) and chalcocite minerals as a function of pH in the range 2 - 9 and time at 25¦C, is presented. Particle zeta potential, reflecting interfacial chemistry, indicated a strong pH-history and particle volume fraction dependency. Pristine particles' zeta potentials measured from high to low pH indicated mineral-specific isoelectric point (iep) at pH range 2 - 5. Subsequent measurements from low to high pH showed pH-history dependency with iep shift to higher pH values, the extent of which also depended upon particle volume fraction and aging time. Pulp pH-mediated particle interactions revealed by shear yield stress analysis displayed a bifurcation behaviour and good compliance with DLVO theory. The maximum pulp yield values occurred at the iep whilst weak rheology was observed where the magnitude of the particle zeta potential was greatest. The pivotal role played by both pulp chemistry and suspension conditions in regulating the particle interactions and concomitant rheological behaviour is highlighted. The implications of the findings with regards to clay-base pulps' handleability and its control during aqueous processing are discussed.  

Sep 13, 2010

Over the longer term, the adoption of new technology is an essential component in the endless tasks of reducing mining costs, improving safety and improving environmental standards. However the choice of which of the many available new technologies to adopt and which not to adopt is not easy and the price of mistakes can be very high. The most important issue for mine developers faced with making such choices is knowing whether or not a new technology has been developed to the stage where the timing is right for its adoption. A system for categorising new mining technologies is provided. It provides a basis for more easily reaching common understandings about various new technologies and the background information supplied provides an understanding of what it takes to get new technologies to the proven stage and the risks of never getting there. Wherever possible, new full-scale mine developments should not rely on unproven technologies. Approaches to handling situations where a proposed new mine development is not feasible on the basis of proven technologies are also provided. If any commitment to the use of unproven technologies is made, a guarantee of high quality development support from the supplier of that technology is essential. Several case studies of successful and unsuccessful new technology development programs at BHP are Provided.

Jan 1, 1997

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.Recent increases in prices for iron ore, together with the potential to produce high iron and low contaminant concentrates, have resulted in a renewed interest in recovering magnetite from banded iron formation and other deposits.Geometallurgical evaluation of magnetite involves approaches to sample preparation, sample analysis and resource estimation that are different from the methods commonly used for haematite iron ore. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.The sampling protocol will typically include the use of Davis Tube analysis. The Davis Tube is a bench-scale test that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery.During resource modelling, the mass magnetic recoveries and concentrate grades may be assigned to a block model using regressions with other chemical constituents, or may be estimated directly. For estimation of the concentrate grades, a weighting can be applied to account for the different mass magnetic recoveries from each sample and the impact of these differences on the concentrate estimates.This paper presents an overview of the use of metallurgical test data in resource evaluation for magnetite deposits.

Jul 11, 2011

It is a very great pleasure indeed to participate in this interesting and important seminar. My two visits to Australia in the past have been extremely pleasant and this one is equally so. My task is to tell you what has been happening in the United States, in these past few years especially, in regard to the management of our air resources and to present in some detail the difficulties we in the copper, lead and zinc smelting industries have been experiencing. The sudden upsurge in interest in air pollution in the United States is a strange phenomenon indeed - strange because we've had air pollution a long time, just as long as there have been large cities using fossil fuels for heating purposes. And the problem has been studied for quite a long time. As early as 1919 studies by the U. S. Bureau of Mines were done in Salt Lake City, where I .live. In the winter of that year extensive measurements were made of airborne particles - dust and smoke. The average concentration of particles found was 870 micrograms per cubic meter of air. A very large number compared to levels we find today. A microgram of course is a very small unit, one twenty-eight millionth of an ounce. A fine human hair two inches long weighs about 100 Micrograms.

Jan 1, 1971

By J A. Cowburn

The high intensity zone within the Jameson Cell is the downcomer. It is largely external and separated from the flotation tank. This, together with operation of the downcomer under vacuum, rather than at elevated pressure and the absence of moving parts, allows ready access to the high intensity zone for measurement and analysis. Experimentation was conducted allowing measurements of recovery for residence times of between 20 milliseconds and ten seconds within the downcomer of a Jameson Cell. The affect of aeration rate on the recovery of different particle sizes was also studied.

Jan 1, 2005

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

By M E. Karmis

Traditional coal mining planning seldom considers key æsustainability factorsÆ such as: societal impacts in the area; jobs (both created and lost); dislocation of towns and residences; impact on neighbouring communities and individuals; infrastructure concerns; post-mining land use (except when limited by law or other factors); habitat disruption and reconstruction; long-term economic impacts in the community; and net long-term community benefit. This paper presents a systems engineering approach based on the premise that systems can only be optimised if all factors are considered at one time. In theory, coal mine designs can be optimised for return on investment, environmental protection and sustainability. Using this approach, the permitting process may be quicker and less costly, relationships with neighbours, communities, environmental groups may be improved, the mining industry may be seen as a positive for the short-term and long-term and the mining industry may increase profits. This paper discusses geographic information system (GIS) tools that may be used to incorporate ecological and other sustainable development concerns into models of coal mine sustainability performance. Along with coal production cost and value information obtained from past and present coal mining operations, GIS data are used to develop mathematical cost and equation models. By analysis of on-the-ground data, the parameters to be included in these models are identified, the relationships between these parameters quantified and the models developed. The paper also discusses the next phases of the work to be completed once the data is obtained and the models are adjusted and validated. At that time, site-specific information will be input into the models and the approach to mining a particular property evaluated and optimised for financial rate-of-return and other desired outcomes, such as preservation or enhancement of sustainability values. Finally, the paper will examine how this approach can be combined with traditional mining engineering considerations in order to develop an optimised mine plan for a specific mining property.

Jan 1, 2009

Safe, efficient production is a common objective for all large open pit mines. Despite comprehensive policies, procedures and regulations aimed at protecting workers, several people die each year in mining equipment-related collisions. The limited sightlines of heavy equipment operators coupled with difficult operating conditions are major contributing factors to the majority of mining equipment collisions. Off road haul trucks are the most common type of machinery involved in surface accidents. These vehicles represent the primary target for improving safety performance by mine operators. Although several commercial products have been introduced to address these issues, none have achieved significant market acceptance. The current collision avoidance solutions lack integration with onboard fleet management and equipment health systems. To achieve acceptance in industry, any collision avoidance system must offer high reliability, minimal false alarms, and value for money. With these criteria in mind, this paper will examine the pros and cons of the various technological approaches to collision avoidance in an open pit mining environment. The unique global positioning systems (GPS) and camera-based proximity detection solution on offer from Modular Mining Systems will be described. This solution uses intelligent filters to minimise false alarms. Tight integration with fleet management provides context information to enhance warnings and enable back-office near-miss analysis. Available today, this combination creates a practical solution to improve the situational awareness of heavy equipment operators, at a compelling price point. Future directions for maximising heavy equipment operator situational awareness will also be examined.

May 1, 2010